• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.4
• /
• pp.381-388
• /
• 2015

In this paper, a wireless video streaming system is designed and implemented for TV white space applications. It consists of a RF transceiver module, a digital modem, a camera, and a LCD screen. A VGA resolution video is captured by a camera, modulated by modem, and transmitted by RF transceiver module, and finally displayed at a destination 2.6-inch LCD screen. The RF transceiver is based on direct-conversion architecture. Image leakage is improved by low pass filtering LO, which successfully covers the TVWS. Also, DC offset problem is solved by current steering techniques which control common mode level at DAC output node. The output power of the transmitter and the minimum sensitivity of the receiver is +10 dBm and -82 dBm, respectively. The channel bandwidth is tunable among 6, 7 and 8 MHz according to regulations and standards. Digital modem is realized in Kintex-7 FPGA. Data rate is 9 Mbps based on QPSK and 512ch OFDM. A VGA video is successfully streamed through the air by using the developed TV white-space RF communication module.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.5
• /
• pp.29-38
• /
• 2013

The G-class cement is commonly used in practice for geothermal well cementing in order to protect a steel casing that is designed to transport hot water/steam from deep subsurface to ground surface during operating a geothermal power plant. In order to maintain optimal performance of geothermal wells, physical properties of the cementing material should be satisfactory. In this paper, relevant factors (i.e., groutability, uniaxial compression strength, thermal conductivity and free fluid content) of the G-class cement were experimentally examined with consideration of various water-cement (w/c) ratios. Important findings through the experiments herein are as follows. (1) Groutability of the G-class cement increases by adding a small dose of retarder. (2) There would be a structural defect caused when the w/c ratio is kept higher in order to secure groutability. (3) Thermal conductivity of the G-class cement is small enough to prevent heat loss from hot steam or water to the outer ground formation during generating electricity. (4) The G-class cement does not form free water channel in cementing a geothermal well. (5) The Phenolphthalein indicator is applicable to the distinction of the G-class cement from the drilling mud.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.6
• /
• pp.457-465
• /
• 2014

This paper introduces a test bed for communication protocol schemes of underwater acoustic sensor network, and also shows experimental results obtained from the test bed. As a testing protocol, carrier sense multiple access/collision avoidance (CSMA/CA) is evaluated on underwater acoustic channel. A sensor node is equipped with a DSP control board of ATmega2560 and a commercial underwater modem produced by Benthos. The control board not only manipulates a GPS signal to acquire the information of location and time, but also controls the underwater modem to operate according to the procedure designed for a given testing protocol. Whenever any event takes place such as exchanging control/data packets between underwater modems and acquiring location and timing information, each sensor node reports them through radio frequency (RF) air interface to a central station located on the ground. The four kinds of packets for CSMA/CA, RTS(Request To Send), CTS(Clear to Send), DATA, ACK(Acknowledgement) are designed according to the underwater communication environment and are analyzed through the lake experiment from the point of feasibility of CSMA/CA in underwater acoustic communications.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.2
• /
• pp.92-108
• /
• 2017

Present work shows a numerical method to analysis of interaction analysis between solitary wave and onshore bridge. Numerical simulation is carried out by TWOPM-3D (three-dimensional one-field model for immiscible two-phase flows), which is based on Navier-Stokes solver. To do this, the solitary wave is generated numerically in numerical wave channel, and numerical results and experimental results were compared and analyzed in order to verify the applicability of force acting on an onshore bridge. From this, we discussed precisely the characteristics of horizontal and vertical forces (uplift and downward forces) changes including water level and velocity changes due to the variation of solitary wave height, water depth, onshore bridge's location and type, and number of girder. Furthermore, It is revealed that the maximum horizontal and vertical forces acting on the girder bridge show different varying properties according to the number of girder, although each maximum force acting on the girder bridge is proportional to the increasement of incident solitary wave height, and the entrained air in the fluid flow affects the vertical force highly.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.12 no.1
• /
• pp.179-214
• /
• 1999

The result were as follows: 1. Yu Wan So(劉完素) regarded the cause of surgical disease as the heat(熱). He used the three method to drain(疏通), promoting pus drainage(托裏) and the balance between ying-energy(營氣) and wei-energy(衛氣). 2. Jang Jong Jeung(張從正) only refered to medicines without entire theory. 3. Lee Dong Won(李東垣) regarded the cause of surgical disease as the greasy diet(膏梁厚味), damp air(濕氣), wetness heat(濕熱). For each treatment he used the method of Yu Wan So's treatment and emphasized the balance between ying-energy(營氣) and wei-energy(衛氣), stomach energy(胃氣). 4. Ju Jin Heung(朱震亨) distinguished the cause of surgical disease from enternal(內), external(外) and channel(經). For each treatment he used the method to drain(疏通), promoting pus drainage(托裏) and the balance between ying-energy(營氣) and wei-energy(衛氣). The first stage used the clearing away heat and toxic materials(淸熱解毒) and the last stage used the invigoration and dispersion(補托). 5. Yu Wan So(劉完素) used to be very busy of Moschus(麝香), Alumen(白礬), Olibanum(乳香), Coptidis Rhizoma(黃連), Minium(黃丹) and Scutel1ariae Radix(黃芩) In classification of the medical action, great part of the medicine are activating blood circulation to dissipate blood stasis(活血祛瘀), clearing away heat and toxic materials( 淸熱解毒) and external application(外用). 6. Jang Jong Jeung(張從正) used to be very busy of Olibanum(乳香), Angelicae Gigantis Radix(當歸), Minium(黃丹), Myrrha(沒藥), Calomelas(輕粉), Rhei Radix Et Rhizoma(大黃) and Phellodendri Cortex(黃柏). In classification of the medical action, great part of the medicine arc activating blood circulation to dissipate blood stasis(活血祛瘀), clearing away heat and toxic materials(淸熱解毒) and diverged wind-cold evil(發散風寒). 7. Lee Dong Won(李東垣) used to be very busy of Forsythiae Fructus(連翹), Scuteliariae Radix(黃芩), Angelicae Gigantis Radix(當歸). Astragali Radix(황기), Glycyrrhizae Radix(炙甘草), Bupleuri Radix(紫胡), Phellodendri Cortcx(黃柏), and Coptidis Rhizoma(黃連). In classification of the medical action, great part of the medicine are activating blood circulation to dissipate blood stasis(活血祛瘀), regulating vital energy(理氣) and clearing away heat and toxic materials(淸熱解毒). 8. Ju Jin Heung(朱震亨) used to be very busy of Glycyrrhizae Radix(甘草), Astragali Radix(황기), Angelicae Gigantis Radix(當歸), Phellodendri Cortex(黃柏), Scutellariae Radix(黃芩), Ginseng Radix(人蔘), Qlibanum(乳香). In classification of the medical action, great part of the medicine are clearing away heat and toxic materiaIs(淸熱解毒), activating blood circulation to dissipate blood stasis(活血祛瘀) and diverged wind-cold evil(發散風寒).

• Tunnel and Underground Space
• /
• v.20 no.2
• /
• pp.82-91
• /
• 2010

Grouting technology is one of the ground improvement methods used in water controlling and reinforcement of rock mass in underground structure construction. It is necessarily required to find out the characteristics of grout flow through discontinuities in a rock mass for an adequate grout design and performance assessment. Laminar flow is not always applicable in simulating a grout flow in a rock mass, since the rock joints usually have apertures at a micro-scale and the flow through these joints is affected by the joint roughness and the velocity profile of the flow changes partially near the roughness. Thus, the influence of joint roughness and aperture on the grout flow in rough rock joint was numerically investigated in this study. The commercial computational fluid dynamics code, FLUENT, was applied for this purpose. The computed results by embedded Herschel-Bulkley model and VOF (volume of fluid) model, which are applicable to simulate grout flow in a narrow rock joint that is filled with air and water, were well compared with that of analytical results and previously published laboratory test for the verification. The injection pressure required to keep constant injection rate of grout was calculated in a variety of Joint Roughness Coefficient (JRC) and aperture conditions, and the effect of joint roughness and aperture on grout flow were quantified.

• Particle and aerosol research
• /
• v.14 no.4
• /
• pp.171-180
• /
• 2018

To optimize the shape of the electrostatic precipitator for the removal of particulate matter in subway environments, the wind-tunnel experiments were carried out to characterize collection efficiency and ozone emission rate. As a standardized parameter, power consumption divided by the square of flow velocity, was increased, the $PM_{10}$ collection efficiency increased. If the standardized parameter is higher than 1.0 due to high power consumption or low flow velocity, increase in thickness of electrodes from 1 to 2 mm, or increase in distance of collection plates from 5 to 10 cm did not change the $PM_{10}$ collection efficiency much. Increase in thickness of high-voltage electrodes, however, can cause decrease in $PM_{10}$ collection efficiency by 28% for low power consumption and high flow velocity. The ozone emission rate decreased as distance of collection plates became wider, because the ozone emission rate per unit channel was constant, and the number of collection channels decreased as the distance of collection plates increased. When the distance of collection plates was narrow, the ozone emission rate increased with the increase of the thickness of electrodes, but the difference was negligible when the distance of collection plates was wide. It was found that the electrostatic precipitator having a thin high-voltage electrodes and a narrow distance of collection plates is advantageous. However, to increase the thickness of high-voltage electrodes, or to increase the distance of collection plates is needed, it is necessary to increase the applied voltage or reduce the flow rate to compensate reduction of the collection efficiency.

• Journal of Aerospace System Engineering
• /
• v.16 no.1
• /
• pp.86-96
• /
• 2022

The development trend of jet fighter's avionics system architecture is the digitization of subsystem component functions, increased RF sensor sharing, fiber optic channel networks, and modularized integrated structures. The avionics system architecture of the fifth generation jet fighters (F-22, F-35) has evolved into an integrated modular avionics system based on computing function integration and RF integrated sensor systems. The integrated modular avionics system of jet fighters should provide improved combat power, fault tolerance, and ease of jet fighter control. To this aim, this paper presents the direction and requirements of the next-generation jet fighter's avionics system architecture through analysis of the fifth generation jet fighter's avionics system architecture. The core challenge of the integrated modularized avionic system architecture requirements for next-generation fighters is to build a platform that integrates major components and sensors into aircraft. In other words, the architecture of the next-generation fighters is standardization of systems, sensor integration of each subsystem through open interfaces, integration of functional elements, network integration, and integration of pilots and fighters to improve their ability to respond and control.

• Korean Journal of Radiology
• /
• v.23 no.5
• /
• pp.539-547
• /
• 2022

Objective: To investigate the association between functional tumor burden of peritoneal carcinomatosis (PC) derived from diffusion-weighted imaging (DWI) and overall survival in patients with advanced ovarian carcinoma (OC). Materials and Methods: This prospective study was approved by the local research ethics committee, and informed consent was obtained. Fifty patients (mean age ± standard deviation, 57 ± 12 years) with stage III-IV OC scheduled for primary or interval debulking surgery (IDS) were recruited between June 2016 and December 2021. DWI (b values: 0, 400, and 800 s/mm²) was acquired with a 16-channel phased-array torso coil. The functional PC burden on DWI was derived based on K-means clustering to discard fat, air, and normal tissue. A score similar to the surgical peritoneal cancer index was assigned to each abdominopelvic region, with additional scores assigned to the involvement of critical sites, denoted as the functional peritoneal cancer index (fPCI). The apparent diffusion coefficient (ADC) of the largest lesion was calculated. Patients were dichotomized by immediate surgical outcome into high- and low-risk groups (with and without residual disease, respectively) with subsequent survival analysis using the Kaplan-Meier curve and log-rank test. Multivariable Cox proportional hazards regression was used to evaluate the association between DWI-derived results and overall survival. Results: Fifteen (30.0%) patients underwent primary debulking surgery, and 35 (70.0%) patients received neoadjuvant chemotherapy followed by IDS. Complete tumor debulking was achieved in 32 patients. Patients with residual disease after debulking surgery had reduced overall survival (p = 0.043). The fPCI/ADC was negatively associated with overall survival when accounted for clinicopathological information with a hazard ratio of 1.254 for high fPCI/ADC (95% confidence interval, 1.007-1.560; p = 0.043). Conclusion: A high DWI-derived functional tumor burden was associated with decreased overall survival in patients with advanced OC.

• Ecology and Resilient Infrastructure
• /
• v.4 no.2
• /
• pp.75-82
• /
• 2017

This study was executed to know the effect of the habitat size on huanren brown frog (Rana huanrensis) larvae's growth. We've conducted the study on Mt. Surak in Sanggye-dong, Nowon-gu, Seoul. Our study site was discriminated the huanren brown frog larvae's habitat into the three different areas, such as small area (S1, $3.91m^2$), middle area (S2, $4.42m^2$), and large area (S3, $38.37m^2$) in the same water channel. We measured two times per a week the 15 huanren brown frog larvae's body length, and developmental stages (foreleg, hind leg, tail length) including the environmental factors (humidity, air temperature and water temperature) of the study site from March 30 to June 28 in 2016. The only hatching rate was measured for the three egg sacs at the S2 study site. We found that the average hatching rate was $76.84{\pm}18.23(%)$ at S2. Generally, because of less precipitation during our study periods, all habitat areas for our study site were gradually decreased. The middle area, S2, was not reduced, the small area, S1, was reduced more than a fourth, and the largest area, S3, was drastically reduced more than half from initial area. There was no statistically difference among the three study sites for the three environmental factors (average humidity, average air temperature, and average water temperature) by F-test, but there were significant difference among the three site for the larvae's body length (F-test p< 0.05). Therefore, the larger of habitat areas, the larger of the larvae length as well as the faster of the larvae's developmental stages. When we measured the body lengths of immature huanren brown frogs, the immature frog of S1 was smallest, the immature frog of S3 was middle lenght, and the immature frog of S2 was largest. There were statistically different among the three study sites for the immature huanren brown frogs (F-test, p< 0.05). Because the S2 study site was relatively stable without rarely changing the study area, it meant that huanren brown frog was sensitive to habitat areas. Based on the results of this study, if we study on the effect of the altitude on the growth rate of huanren brown frog, it must be helpful in understanding the habitat environment of the population of huanren brown frog.