• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.1196-1201
• /
• 1993

Test of Caterpillar Challenger 65 tractor which has rubber tracks, and articulated four wheel drive tractor with dual wheels and a mechanical front wheel drive tractor were conducted on an unplowed and plouwed wheat stubble field. The following parameters were analyzed : tractive efficiency (ηv), net tractive coefficient ($\phi$n), slip ($\sigma$) , drawbar pull(Fv), drawbar power (Pv) and forward velocity(v). The maximum net tractive coefficient was established at the tractive efficiency of 0.60 on the unplowed wheat stubble field : for the Challenger 65 tractor 0.855 ; 4WD 0.624 and MFWD 0.534 and on the plowed wheat stubble field with the tractive efficiency of 0.40 for the Challenger 65 tractor 0.82 : 4WD 0.57 and for tractor MFWD 0.48.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.506-512
• /
• 2000

Performance of a four- wheel tractor fabricated by Tongyang Moolsan Co., Ltd, Korea was tested in Thailand during May-June 2000. Wheel slip and field capacity were measured in three fields using different traction devices and implements. The tractor worked satisfactorily in the test conditions. Wheel slip of 26.05-33.63 % and the field capacity of 0.17 - 0.20 ha/hr were observed during plowing operation. Further tractive performance tests using a three-point linkage configuration are recommended in Thailand field conditions. Different designs of cage wheels are recommended to be tested to optimize the tractive performance.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.1055-1062
• /
• 1996

A method for automatically driving paddy vehicles, such as rice transplanters, etc., straight ahead in a paddy field was investigated . The direction of such vehicles must be precisely controlled to do the operations as straight. However, the alignment of the from wheels becomes distorted due to the unevenness of the ground, preventing the vehicle form going straight. If the proper alignment of the front wheels is maintained , the vehicle can be driven straight ahead greater precision. To investigate the influence of the ground uneveness, the behavior of a paddy vehicle running over an obstacle was quantified. The left wheel ran over an obstacle on a flat concrete road surfaced. When the steering wheel was free, the front wheels were forced toward the left when vehicle went up the obstacle and toward the right when the vehicle went down it. The torsion of the wheel when the vehicle went down the obstacle was larger than that when it went up ,so it turned right 5 degrees. Sinc hydraulic control steering decreased the steering angle , it turned right 3 degrees. These results suggest that a vehicle can be driven straight ahead with high precision when the steering angle is changed in response to the direction and inclination of the vehicle . Such results were obtained in a paddy field tests.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.3
• /
• pp.81-86
• /
• 2005

The agricultural working tractor of this study is equipped with 4 wheel driving system developed in study 1 and 4-type wheel steering system. The wheel steering system has four type of steering methods that are front wheel steering, rear wheel steering, 4 wheel steering with opposite phase, and 4 wheel steering with corresponding phase. This study introduces the hydraulic circuit of the 4-type wheel steering system and the construction of working tractor. Judging from the field test results of the developed working tractor, it is apparent that 4-type wheel steering system has many advantages when driving in a narrow corral.

• Journal of Biosystems Engineering
• /
• v.25 no.2
• /
• pp.79-88
• /
• 2000

Effects on tractive performance of design parameters of cage wheel as a traction aid to driving tires of tractor in wet paddy field were investigated experimentally. an experimental cage wheel was designed so that the design parameters such as wheel diameter, wheel width, lug pitch and lug angle could be varied during traction test, The traction test was conducted in two different types of wet paddy field ; shallow and deep harpan fields . Experimental results showed that tractive performance is affected by both soil conditions and the design parameters. A considerable improvement on the tractive performance was obtained by using a cage wheel with 45$^{\circ}$ lug angle in shallow hardpan and smaller lug pitch in deep hardpan. The diameter of cage wheel was mostly influential to the tractive performance both in shallow and deep hardpans.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.1013-1025
• /
• 1993

Agriculture in Swaziland is the most important sector of the economy from the stand point of export earning, rural employment and dependency for family food. But, inspite of 65.5 percent of the household being busy in food production for family consumption in Swaziland, the import bill of food and live animals is rising from E119.7268 million in 1987/90 (An.St.Bul.1988) . A typical farm size, based on holding's growing crops, is only 1.93 ha which may prohibit owning a four wheel tractor for farm operations. The traditional hand tools are just not efficient and comfortable to operate in order to exploit full potential of the land. There are over 120.000 draught animals which have potential to be utilized in farming. The two wheel-tractor is another energy source which can be used for many farm-operations.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.285-295
• /
• 2018

Purpose: The aim of this study is to develop a three-wheel riding cultivator for improving the performance of the current four-wheel riding cultivators in the market. Methods: A prototype three-wheel riding cultivator with the rated power of 15.5-kW, a primary hydrostatic and a two-speed selective gear transmission shifts, front/rear three-wheel drive, a hydraulic wheel tread adjustment, and the mid-section attachment of the major implements was designed and constructed. Its specifications and basic performance are investigated. Results: The maximum speeds of the prototype at the low and high stages were measured to be approximately 7.31, and 11.29 km/h in forward travel, respectively, and approximately 3.60, and 6.37 km/h in rearward travel, respectively. The minimum ground clearance is shown to be 670 mm. The rotating speeds of the power takeoff (PTO) shaft at the low and high stages are shown to be approximately 795 and 1,140 rpm, respectively. The tread of the rear wheels, the minimum radius of turning, and the maximum lifting height of the parallel link device are measured to be within 1,320-1,720 mm, 2.80 m, and 390 mm, respectively. Approximately 25.3% and 74.7% of the total weight of the prototype are distributed in the front and rear wheels on flat ground, respectively. When the tread of rear wheels increased from 1,320 to 1,720 mm, the left and right static lateral overturning angles increased from $33.4^{\circ}$ to $39.1^{\circ}$ and from $29.0^{\circ}$ to $36.1^{\circ}$, respectively. Conclusions: The prototype three-wheel riding cultivator showed a wide range of travel and PTO speeds, high minimum ground clearance, small minimum radius of turning, and easy control of the rear wheel tread. Further, the easy observation of cultivating operations by mid-mounting the implements can improve quality of work. Therefore, the prototype is expected to contribute to the riding mechanization of cultivating operations for various upland crops in Korea.

• Journal of Biosystems Engineering
• /
• v.41 no.4
• /
• pp.288-293
• /
• 2016

Purpose: The purpose of this study was to investigate the key factors in designing a three-wheeled two-row soybean reaper (riding type) that is suitable for soybean production, and ensure worker safety by proposing optimal work conditions for the prototype of the designed machine in relation to the slope of the road. Methods: A three-wheeled two-row soybean reaper (riding type) was designed and its prototype was fabricated based on the local soybean-production approach. This approach was considered to be closely related to the prototype-designing of the cutter and the wheel driving system of the reaper. Load distribution on the wheels of the prototype, its minimum turning radius, static lateral overturning angle, tilt angle during driving, and The working and rear overturning (back flip) angle were measured. Based on the gathered information, investigations were conducted regarding optimal work conditions for the prototype. The investigations took into account driving stability and worker safety. Results: The minimum ground clearance of the prototype was 0.5 m. The blade height of the prototype was adjusted such that the cutter was operated in line with the height of the ridges. The load distribution on the prototype's wheels was found to be 1 (front wheel: F): 1.35 (rear-left wheel: RL): 1.43 (rear-right wheel: RR). With the ratio of load distribution between the RL and RR wheels being 1: 1.05, the left-to-right lateral loads were found to be well-balanced. The minimum turning radius of the prototype was 2.0 m. Such a small turning radius was considered to be beneficial for cutting work on small-scale fields. The sliding of the prototype started at $25^{\circ}$, and its lateral overturning started at $39.3^{\circ}$. Further, the critical slope angle for the worker to drive the prototype in the direction of the contour line on an incline was found to be $12.8^{\circ}$, and the safe angle of slope for the cutting was measured to be less than $6^{\circ}$. The critical angle of slope that allowed for work was found to be $10^{\circ}$, at which point the prototype would overturn backward when given impact forces of 1,060 N on its front wheel. Conclusions: It was determined that farmers using the prototype would be able to work safely in most soybean production areas, provided that they complied with safe working conditions during driving and cutting.

• Journal of Biosystems Engineering
• /
• v.8 no.2
• /
• pp.11-17
• /
• 1983

Stress distribution under a driving lugged wheel was obtained by photoelastic method. The distribution showed two distinct parts, one part is due to sinkage and other due to compression. Results of the study are summarized as follows. 1. The tangential reactions of sinkage as well as compressing parts were directly proportional to tangential load to the driving wheel, that's appeared to be thrust of the driving wheel. The normal reactions of both sinkage and compressing parts were directly proportional to the vertical load to the driving wheel, that's appeared to be resistance against wheel motion. 2. When the tangential load was constant, changing the vertical load did not show any significant thrust variation of the driving wheel. 3. Under the condition of this experiment, the ratio of vertical load to tangential load (T.L/V.L) must be greater than 1.0 in order for the wheel to roll.

• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.205-210
• /
• 2009

It has been known from Willoughby's empirical equation that rating cone index can be determined if wheel sinkage and slip of a vehicle can be measured on soil surface. A field data of wheel sinkage and slip was collected from two tractors of different sizes on gravelly sand and gravelly loamy sand. Using the data, rating cone index of the soil was estimated. The estimated rating cone index demonstrated that it could be determined in real time by measuring wheel sinkage and slip. It was also demonstrated statistically that the same soil strength could be obtained under the same soil conditions regardless of the vehicle platforms used for the wheel sinkage and slip measurements.