• Korean Journal of Materials Research
• /
• v.25 no.12
• /
• pp.683-689
• /
• 2015

In this study, the properties of Ag-coated $TiO_2$ nanoparticles were observed, while varying the molar ratio of water and $Ag^+$ for the surfactant and $TiO_2$. According to the XRD results, each nanoparticle showed a distinctive diffraction pattern. The intensity of the respective peaks and the sizes of the nanoparticles increased in the order of AT1($R_1=5$)(33.3 nm), AT2($R_1=10$)(38.1 nm), AT3($R_1=20$)(45.7 nm), AT4($R_1=40$)(48.6 nm) as well as AT5($R_2=0.2$, $R_3=0.5$)(41.4 nm), AT6($R_2=0.3$, $R_3=1$)(45.1 nm), AT7($R_2=0.5$, $R_3=1.5$)(49.3 nm), AT8($R_2=0.7$, $R_3=2$)(57.2 nm), which values were consistent with the results of the UV-Vis. spectrum. The surface resistance of the conductive pastes fabricated using the prepared Ag-coated $TiO_2$ nanoparticles exhibited a range 7.0~9.0($274{\sim}328{\mu}{\Omega}/cm^2$) times that of pure silver paste(ATP)($52{\mu}{\Omega}/cm^2$).

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.76-76
• /
• 2009

눈부신 전자산업의 발달로 대부분의 전자제품이 다기능/경박단소화 되고 있어, 고밀도 실장 기술인 양면 표면실장과 고집적 패키징 기술인 패키지 적층 공정의 적용이 점차 확대되고 있다. 따라서 양면 표면실장 및 패키지 적층 공정에 사용되는 저온 접합용 무연 솔더 즉, $183^{\circ}C$(Sn-37Pb 공정 솔더 융점) 이하의 융점을 가지는 저온 무연 솔더에 대한 관심이 높아지고 있다. 한편, 미세피치 적용 분야에 있어 ACF/P를 이용한 COG 접속 분야 외에도 최근 저온 접합용 무연 솔더를 이용한 접속 분야가 각광을 받고 있다. 따라서, 접속피치 미세화에 대응하기 위해 스크린 인쇄성을 향상시킬 수 있는 저온 무연 솔더 paste 제조 및 공정 기술의 개발이 필요한 실정이다. 현재 대표적인 저온 무연 솔더 조성은 Sn-Bi계($138^{\circ}C$ 융점)와 Sn-In계($120^{\circ}C$ 융점)이다. 하지만, 이들 조성의 신뢰성 등에 있어 개선의 여지가 있으므로 이를 해결하기 위한 무연솔더 조성의 개발이 필요하다. 이와 같은 관점에서, 본 연구는 $137^{\circ}C$의 융점을 갖는 Sn-57.6Ag-0.4Ag 저온 무연 솔더 paste를 $217^{\circ}C$의 융점을 갖는 Sn-3.0Ag-0.5Cu 솔더 paste와 비교하여 인쇄성, reflow 특성, void inspection, 미세조직 관찰 및 underfill 적용 등의 실험을 실시하였다.

• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.663-667
• /
• 2003

The effects of paste materials on field emission properties in a carbon nanotube(CNT) cathode were investigated for high-efficient field emission displays. The major components in CNT paste for screen printing were a metallic Ag-paste, a dielectric glass-frit and CNT ink. The emission current from the cathode by an electron tunneling effect increased with an increase in the dielectric material fraction in the CNT paste, which is related to an increase of field enhancement factor in Fowler-Nordheim equation. The surface treatment used, after soft baking of the screen-printed CNT films, greatly affected the decrease in the turn-on field in CNT cathode and the uniformity of emission sites over the entire CNT film area.

• Korean Journal of Materials Research
• /
• v.13 no.1
• /
• pp.18-23
• /
• 2003

Properties of Ag thick films fabricated by using low temperature curable silver pastes were investigated. Ag pastes were consisted of polymer resins and silver powders. Ag pastes were used for conductive or fixing materials between board and various electrical and electronic devices. Low temperature curable Ag pastes have some advantages over high temperature curable types. In cases of chip mounting, soldering properties were required for screen printed Ag thick films. In this study, four types of Ag pastes were fabricated with different compositions. Screen printed Ag thick films on alumina substrates were fabricated at various curing temperatures and times. Thickness, resistivity, adhesive strength and solderability of fabricated Ag thick films were characterized. Finally, Ag thick films produced using Ag pastes, sample A and B, cured at $150^{\circ}C$ for longer than 6 h and $180^{\circ}C$ for longer than 2 h, and $150^{\circ}C$ for longer than 1 h and $180^{\circ}C$ for 1 h, respectively, showed low resistivities of $10^{-4}$ $∼10^{-5}$ Ωcm and good adhesive strength of 1∼5 Mpa. Soldering properties of those Ag thick films with curing temperatures at solder of 62Sn/36Pb/3Ag were also investigated.

• Proceedings of the Korean Reliability Society Conference
• /
• 2001.06a
• /
• pp.489-496
• /
• 2001

컴퓨터 키보드의 시장 불량품을 분석한 결과 여러 키가 동시에 입력되는 현상이 다수 발생되는 것을 알 수 있었다. 정밀분석결과 이의 원인이 키보드 membrane의 패턴을 구성하는 은(Ag) paste의 ion migration발생에 의한 것임을 알 수 있었다. 재현실험을 통해 고온 고습한 환경에서 장시간 사용하다보면 membrane내부로 수분이 침투하여 패턴간에 Ag ion migration이 발생되어 키 동작 오류를 유발시킴을 알 수 있었다. 이에 대한 대책안으로 제조 원가에 크게 영향을 주지 않으면서 migration을 크게 억제할 수 있는 준방수 방식의 membrane을 채택하여 4$0^{\circ}C$, 90%RH 환경에서 최소 5년을 보증할 수 있는 키보드를 제작하였다. 또한, 키보드 membrane의 ion migration 시험시 정상사용 조건을 가속시킬 수 있는 재현 및 검증시험법(85$^{\circ}C$, 85%RH, 가속계수 17배)을 개발하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.524-529
• /
• 2008

In this paper, in order to develop low loss multilayer actuator, piezoelectric properties of PZW-PMN-PZT multilayer actuator sintered at $900^{\circ}C$ low temperature were investigated according to the number of multilayer. The multilayer actuator was fabricated using tape casting method and used pure Ag internal electrode. The density above $8.0\;g/cm^3$ was obtained at all specimens. With increasing number of multilayer, effective electromechanical coupling factor($k_{eff}$) was increased. $k_{eff}$ of multilayer actuator shows the maximum value of 0.283 at 11 layers actuator. However, effective mechanical quality factor(Qm') was decreased according to the increase of number of multilayer. The Qm' of multilayer actuator showed the maximum value of 920 at 5 layers actuator.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.331-338
• /
• 2005

The rapid advances in high power light sources and arrays as encountered in incandescent lamps have induced dramatic increases in die heat flux and power consumption at all levels of high power LED packaging. The lifetime of such devices and device arrays is determined by their temperature and thermal transients controlled by the powering and cooling, because they are usually operated under rough environmental conditions. The reliability of packaged electronics strongly depends on the die attach quality, because any void or a small delamination may cause instant temperature increase in the die, leading sooner or later to failure in the operation. Die attach materials have a key role in the thermal management of high power LED packages by providing the low thermal resistance between the heat generating LED chips and the heat dissipating heat slug. In this paper, thermal transient characteristics of die attach in high power LED package have been studied based on the thermal transient analysis using the evaluation of the structure function of the heat flow path. With high power LED packages fabricated by die attach materials such as Ag paste, solder paste and Au/Sn eutectic bonding, we have demonstrated characteristics such as cross-section analysis, shear test and visual inspection after shear test of die attach and how to detect die attach failures and to measure thermal resistance values of die attach in high power LED package. From the structure function oi the thermal transient characteristics, we could know the result that die attach quality of Au/Sn eutectic bonding presented the thermal resistance of about 3.5K/W. It was much better than those of Ag paste and solder paste presented the thermal resistance of about 11.5${\~}$14.2K/W and 4.4${\~}$4.6K/W, respectively.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.74-74
• /
• 2009

카본나노튜브(CNT) 복합체는 우수한 기계적 성질을 가지고 있어 다양한 분야에서 연구되고 있다. 본 연구에서는 카본나노튜브(CNT)를 간단한 볼밀공정을 사용하여 Sn3.5Ag solder ball과 SAC305 powder 표면에 혼합하고 이를 통해 접합부 특성을 관찰하였다. 볼밀을 실시하기 전 카본나노튜브(CNT)는 초음파을 이용하여 분산을 실시하였다. Sn3.5Ag solder ball의 직경은 450um이고 SAC305 powder의 직경은 약 30um이었으며 이때 사용한 볼밀볼의 직경은 각각 3mm, 1mm이다. 볼밀 회전속도는 약 300rpm이고 6, 12, 18, 24시간동안 볼밀을 실시하였다. 24시간 볼밀 후에도 solder ball과 solder powder의 모양은 크게 변하지 않았다. SEM을 통해 표면을 관찰한 결과 분산된 카본나노튜브(CNT)는 solder ball과 solder powder의 표면에서 관찰되었다. 카본나노튜브(CNT)가 삽입된 solder ball은 BGA coupon 위에 놓고 Reflow를 실시하여 접합하였고 solder powder은 flux를 첨가하여 paste로 제조하여 2012 chip에 대한 접합특성을 관찰하였다. 카본나노튜브(CNT)는 solder ball 내부의 표면근처에서 관찰되었으며 카본나노튜브(CNT)가 혼합된 solder ball은 Aging 실시 후에 IMC 두께가 카본나노튜브(CNT)가 혼합되지 않은 solder ball에 비해 두께가 작고 접합강도는 약 10% 증가하였다. 또한 카본나노튜브(CNT)가 혼합된 solder paste와 카본나노튜브(CNT)가 혼합되지 않은 solder paste를 비교한 결과 인쇄성은 모두 양호하였으며 카본나노튜브(CNT)가 혼합된 paste를 사용한 chip의 전단강도가 높게 나타났다.

• Journal of the Korean Applied Science and Technology
• /
• v.40 no.1
• /
• pp.71-80
• /
• 2023

Silver paste is a valuable electrode material for electronic device applications because it is easy to handle with relatively low heat treatment. This study treated the electrode surface using an atmospheric-pressure plasma jet on the silver-paste electrode. This plasma jet was generated in an argon atmosphere using a high voltage of 5.5 to 6.5 kV with an operating frequency of 11.5 kHz. Plasma-jet may be more beneficial to the printing process by performing it at atmospheric pressure. The electrode surface becomes hydrophilic quickly and contact angle variation is observed on the electrode surface as a function of plasma treatment time, applied voltage, and gas flow rate. Also, there was no deviation in the contact angle after the plasma treatment in the large-area sample, that means a uniform result could be obtained regardless of the substrate size. The outcomes of this study are expected to be very useful in forming a stacked structure in the manufacture of large-area electronic devices and future applications.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.4
• /
• pp.219-224
• /
• 2006

Silver paste with low sintered temperature has been developed in order to apply electronic parts, such as bus electrode, address electrode in PDP (Plasma Display Panel) with large screen area. In this study, nano-sized silver particles with 10-30 nm were synthesized from silver nitrate ($AgNO_3$) solution by chemical reduction method and silver paste with low sintered temperature was prepared by mixing silver nanoparticles, conventional silver powder with the particle size 1.6 um and Pb-free frit. Conductive thick film from silver paste was fabricated by screen printing on alumina substrate. After firing at $540^{\circ}C$, the cross section and surface morphology of the thick films were analyzed by FE-SEM. Also, the sheet resistivity of the fired thick films was measured using the four-point technique.