• Journal of Hydrogen and New Energy
• /
• v.25 no.5
• /
• pp.509-515
• /
• 2014

At the fuel processing system (FPS) of fuel cell vehicle, hydrogen recirculation blower (HRB) is used for the recirculation of remained hydrogen after reaction. In this paper, noise and vibration improvement of HRB is studied by changing design and control. It is checked the campbell diagram and critical speed for stability of rotor, and housing stiffness is improved using simulation of frequency response function (FRF). A method is suggested that can decrease the unbalance amount of the rotor and impeller which main source of noise and vibration. In order to reduce the noise during deceleration of blower, electrical braking is applied and tested the risk impact of durability. Founded the optimum switching frequency of the motor control, and reduced the idle rpm by increasing of aerodynamic performance. The superiority of paper is proved by measurement of the improved product's noise and vibration.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1914-1922
• /
• 2004

This paper provides a comprehensive study of optimum design of a helicopter tailrotor driveshaft made of the flexible matrix composites (FMCs). Since the driveshaft transmits power while subjected to large bending deformation due to aerodynamic loadings, the FMCs can be ideal for enhancing the drivetrain performance by absorbing the lateral deformation without shaft segmentation. However, the increased lateral flexibility and high internal damping of the FMCs may induce whirling instability at supercritical operating conditions. Thus, the purpose of optimization in this paper is to find a set of tailored FMC parameters that compromise between the lateral flexibility and the whirling stability while satisfying several criteria such as torsional buckling safety and the maximum shaft temperature at steadystate conditions. At first, the drivetrain was modeled based on the finite element method and the classical laminate theory with complex modulus approach. Then, an objective function was defined as a combination of an allowable bending deformation and external damping and a genetic algorithm was applied to search for an optimum set with respect to ply angles and stack sequences. Results show that an optimum laminate consists of two groups of layers: (i) one has ply angles well below 45$^{\circ}$ and the other far above 45$^{\circ}$ and (ii) the number of layers with low ply angles is much bigger than that with high ply angles. It is also found that a thick FMC shaft is desirable for both lateral flexibility and whirling stability. The genetic algorithm was effective in converging to several local optimums, whose laminates exhibit similar patterns as mentioned above.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.547-556
• /
• 2010

For the safety of aircraft and accuracy of bombs, many companies have researched the new concept of adaptive kit to flying-bombs. For the long distance flying, it's normally used deployed high-aspect ratio wing because of limited volume. The probabilities of large elastic deformation and flutter are increased due to decreased stiffness of high-aspect ratio wing. In this paper, computational fluid dynamics and computational structure dynamics interaction methodology are applied for prediction of aerodynamic characteristics. FLUENT and ABAQUS are used to calculate fluid and structural dynamics. Code-bridge was made base on the compactly supported radial basis function to execute interpolation and mapping. There are some differences between rigid body and fluid-structure interaction analysis which are results of aerodynamics characteristics due to structural deformation. Small successive vibration was observed by interaction.

• Journal of Biosystems Engineering
• /
• v.33 no.3
• /
• pp.173-178
• /
• 2008

Some physical properties of rapeseed were measured at five moisture levels of 10.03, 14.91, 20.07, 25.06 and 30.12% (w.b.), which include frictional properties (coefficient of static friction, emptying and filling angle of repose) and aerodynamic properties (terminal velocity and drag coefficient). The physical properties of rapeseed were evaluated as a function of seed moisture content. In the moisture content range, the coefficients of static friction, emptying and filling angle of repose increased linearly with increase of moisture content. The maximum values of coefficients of static friction were on the acrylic surface, varied from 0.34 to 0.43; the next is on the galvanized steel, varied from 0.30 to 0.38; and the minimum were on stainless steel surface, varied from 0.27 to 0.35. Emptying and filling angle of repose varied from 26.12 to 29.62 and 23.83 to 27.05 degrees, respectively. Terminal velocity increased linearly from 3.47 to 3.91 m/s with increase of moisture content. Drag coefficient varied from 1.84 to 1.64 as the moisture content increased. The relationship between drag coefficient and moisture content were expressed by non-linear equation.

• Wind and Structures
• /
• v.26 no.4
• /
• pp.191-204
• /
• 2018

This article presents a study of the largest-ever (height = 220 m) cooling tower using the large eddy simulation (LES) method. Information about fluid fields around the tower and 3D aerodynamic time history in full construction process were obtained, and the wind pressure distribution along the entire tower predicted by the developed model was compared with standard curves and measured curves to validate the effectiveness of the simulating method. Based on that, average wind pressure distribution and characteristics of fluid fields in the construction process of ultra-large cooling tower were investigated. The characteristics of fluid fields in full construction process and their working principles were investigated based on wind speeds and vorticities under different construction conditions. Then, time domain characteristics of ultra-large cooling towers in full construction process, including fluctuating wind loads, extreme wind loads, lift and drag coefficients, and relationship of measuring points, were studied and fitting formula of extreme wind load as a function of height was developed based on the nonlinear least square method. Additionally, the frequency domain characteristics of wind loads on the constructing tower, including wind pressure power spectrum at typical measuring points, lift and drag power spectrum, circumferential correlations between typical measuring points, and vertical correlations of lift coefficient and drag coefficient, were analyzed. The results revealed that the random characteristics of fluctuating wind loads, as well as corresponding extreme wind pressure and power spectra curves, varied significantly and in real time with the height of the constructing tower. This study provides references for design of wind loads during construction period of ultra-large cooling towers.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.3
• /
• pp.199-212
• /
• 2014

This paper describes an autonomous air combat guidance law using a Virtual Pursuit Point (VPP) in one-on-one close engagement for Unmanned Combat Aerial Vehicle (UCAV). The VPPs that consist of virtual lag and lead points are introduced to carry out tactical combat maneuvers. The VPPs are generated based on fighter's aerodynamic performance and Basic Fighter Maneuver (BFM)'s turn circle, total energy and weapon characteristics. The UCAV determines a single VPP and executes pursuit maneuvers based on a smoothing function which evaluates probabilities of the pursuit types for switching maneuvers with given combat states. The proposed law is demonstrated by high-fidelity real-time combat simulation using commercial fighter model and X-Plane simulator.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.11
• /
• pp.903-910
• /
• 2014

Electric fans, which consist of axial blades, are operated by the induction motor. In this paper, the objective of this study is the performance improvement of the base model fan using the design optimization. In order to aerodynamic analysis, computational simulations are performed using commercial tool ANSYS-CFX ver. 14.5. And k-${\omega}$ SST turbulence model is used for the CFD analysis. The design variables are set up as sweep and lean angles. Volumetric flow rate and torque of the fan blades are fixed to objective function. The optimized model is shown the increment of the volumetric flow rate and the reduction of the torque compared with the base model. The experimental procedure is followed KS C 9301. CFD results and experimental results are fairly well matched.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.15 no.1
• /
• pp.21-26
• /
• 2004

Vocal Register Transition(Passaggio) is one of the most important vocal technique for classically trined male singers(tenor). Passaggio is that it bridges the chest register to head register without a noticeable voice break. Vocalist gest the feeling that voice is not locked a particular register. The purpose of this study was to clarify the difference between easy($B_3$) tone and non passaggio(F#_4$) & passaggio(F#_4$). We selected 6 trained singers(tenor), who had more than 12.6 years of experience and were well trained in passaggio technique. Simulataneous measurement was performed frequency(F0), mean flow rate(MFR), intensity(I), and subglottal pressure(Psub) using a phonatory function analyzer(Nagashima) and Closed Quotient(CQ), Jitter, Shimmer, NHR a Electro-glottography(EGG) of Lx. Speech Studio(Laryngogrph Lt, London, UK) and vocal efficiency was calculated by Carroll's method. For the tenor, target tone/a/was measured in three conditions : 1) easy phonation : $B_3$, 2) high tone without passaggio : F#_4$, 3) high tone with passaggio : F#_4$). The results revealed that F0 of the target tones between non-passaggio group and passaggio group were not significantly different though higher is F0, higher is subglottal pressure. And also CQ, MFR, Psub were increased in passagio than nonpssagio but these values were not statistically different. This study concluded that passaggio is the vocal technique to make the same quality of tone between chest register and head register in tenor.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.5
• /
• pp.476-483
• /
• 2007

One of the main function of Ieodo Ocean Research Station is to service the information about the weather and fishing grounds condition which are collected through calibrating convection flow and ocean current around the station. However, due to the influence of the station's structure below sea level, it is difficult to obtain the exact flow data. Therefore, it is required to research on the effect of the structure and the method to evaluate and revise the observed data. In this paper, as a basic study, it deals with the algorithm that simulate the interaction between ocean current and the station structure, followed by discussions about the way to applicate the algorithm. Through 3-dimensional computational fluid dynamics analyses (using Navier-Stokes equations with K-turbulence model), the influence of the station and submerged rocks are quantitatively evaluated, and we would suggest methods how to obtain accurate flow information from the measured rough data.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.751-759
• /
• 2008

In this study, the effect of an unsteady flow field around a body of aerostatic/aerodynamic forces were investigated using rectangular cylinders (B/D = 2, 3, 4, 5). Proper orthogonal decomposition (POD) was introduced to the analysis of the fluctuating pressure field that was measured on the stationary/oscillatory B/D=4 rectangular cylinder, and the characteristics of the proper functions with flow patterns were identified. In addition, the physical decoupling and interactions in the different co-existing flow patterns were investigated through POD. The comparison with the identified proper function associated with a particular flow pattern revealed that the Karman vortex is almost not affected by the separation bubble, but that the Karman vortex considerably interferes in the development of the separation bubble around the trailing edge. It can be considered that the Karman vortex induces the increment of the curvature of the substantial separated flow.