• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.861-864
• /
• 2006

In general, 4-pole parameter and three-point method are used for predicting transmission loss which is one of characteristics of Muffler using CAE tools. However, these mehtods show different results from experiment when the flow effects are presented in practical model. In this parer, to overcome these problems, both Fluent and.Sysnoise are used to analyze the performance of extended inlet/outlet muffler including flow effects with varying flow velocity at inlet of duct. Flow fields and quadrupole source is calculated by Fluent. And Sysnoise is used to analyze acoustic performances of muffler with quadrupole source data extracted from Fluent. Finally, the variation of transmission loss is estimated according to various inlet flow velocity.

• 한국소음진동공학회논문집
• /
• 제18권6호
• /
• pp.612-618
• /
• 2008

Microphone array beamforming method has been recognized as an important aeroacoustic research field and become a standard technique in localizing sound sources. This method also used in flight acoustic measurement, and especially, it is very useful when measure sounds inside the wind tunnel. In measuring sound which is inside the wind tunnel by traditional beamforming method, there are some errors caused by airstream. The speed and the propagation path of the sound changes as it travel through the airstream. This makes the error which the position of sound is changed a little bit to the down stream direction. In this paper, validation test has made about the correction equation for this wind effects of previous researches. And beamforming including shear layer correction was performed about a sound source in the anechoic open-jet wind tunnel.

• 한국소음진동공학회논문집
• /
• 제25권3호
• /
• pp.150-159
• /
• 2015

An experimental study on frequency characteristics of the microphone array covered with Kevlar sheet was conducted in the closed test section. Microphones that were flush-mounted in the wall of wind tunnel were subjected to very high flow noise resulting from the turbulence in the wall boundary layer. This noise interference by the boundary layer was referred as 'a microphone self-noise' and various approaches were studied to reduce this interference. Recessed microphone array with high tensioned cover was one of the good approaches to reduce this self-noise. But, the array cover could cause an unexpected interference to the measuring results. In this paper the frequency characteristics of the microphone array with Kevlar cover was experimentally studied. The white noise was used as a reference noise source. Three kinds of tensions for the Kevlar cover were tested and those results were compared with the test results without the Kevlar cover. The gap effect between the cover and microphone head was also tested to find out the proper position of microphone in the array module. Test results show that the mid-tension and 10mm gap was the best choice in the tested cases.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권1호
• /
• pp.48-55
• /
• 2017

Aeroacoustic computation of a fully-developed turbulent pipe flow at $Re_{\tau}=175$ and M = 0.1 is conducted by LES/LPCE hybrid method. The generation and propagation of acoustic waves are computed by solving the linearized perturbed compressible equations (LPCE), with acoustic source DP(x,t)/Dt attained by the incompressible large eddy simulation (LES). The computed acoustic power spectral density is closely compared with the wall shear-stress dipole source of a turbulent channel flow at $Re_{\tau}=175$. A constant decaying rate of the acoustic power spectrum, $f^{-8/5}$ is found to be related to the turbulent bursts of the correlated longitudinal structures such as hairpin vortex and their merged structures (or hairpin packets). The power spectra of the streamwise velocity fluctuations across the turbulent boundary layer indicate that the most intensive noise at ${\omega}^+$ < 0.1 is produced in the buffer layer with fluctuations of the longitudinal structures ($k_zR$ < 1.5).

• 한국유체기계학회 논문집
• /
• 제5권2호
• /
• pp.36-42
• /
• 2002

A new method to calculate the aeroacoustic pressure of a centrifugal fan that is used in a vacuum cleaner has been developed. The centrifugal fan consists of the impeller, the diffuser, and the circular casing. Due to the high rotating speed of the impeller and the small gap distance between the impeller and diffuser, the centrifugal fan makes very high noise levels at BPF and its harmonic frequencies. In order to calculate the sound pressure of a centrifugal fan, the unsteady flow field data is needed. This unsteady flow field is calculated by the vortex method. The sound pressure is then calculated by acoustic analogy. In this paper, only dipole term is considered in the equation. The noise generated by moving impeller and stationary diffuser is calculated separately. The predicted acoustic pressures agree very well with the measured data. The difference between the two is less than 4dB

• 한국소음진동공학회논문집
• /
• 제24권3호
• /
• pp.171-179
• /
• 2014

썬루프 버페팅 현상은 차량 주행시 발생하는 주요 바람소리 문제점 중 하나이다. 버페팅 문제점을 해결하기 위해서 전산 해석을 적용한다면, 실험적 방법보다 비용을 절감할 뿐 아니라 발생 원리 또한 규명할 수 있다. 그러나 전산 해석을 이용하기 위해서는 해석 결과의 정확성이 보장되어야 실제 차량 개발에 적용할 수 있다. 이 연구에서는 해석적 방법의 정확도 향상을 위해 주요 상업용 전산해석 소프트웨어들의 썬루프 버페팅 현상 예측에 대한 벤치마크 테스트를 수행하였다. 해석 대상은 차량의 형상을 간략하게 만든 HSM(Hyundai simplified model)을 이용하였고, 정확도 비교를 위해 속도별 버페팅 현상에 대한 실험을 현대자동차 공력무향풍동에서 실차내부의 흡음재에 의한 효과를 해석적으로 고려하기 위해 음향 응답 실험을 수행하여 해석 결과 정확도 향상을 위해 각 상용 소프트웨어 제작사에 해석 전에 제공 하였다. 이 연구를 통해 대부분의 상용 소프트웨어들이 실험결과와 유사한 해석 결과를 도출하였다. 또한, 실제 차량 개발에서 적용하기 위한 해석 예측 우선순위를 서로 공유하여 추가 해석을 통해 차량 개발에 적용 가능한 보다 정밀한 해석 정확도를 얻어낼 수 있었다.

• 한국항공우주학회지
• /
• 제44권5호
• /
• pp.381-390
• /
• 2016

본 연구에서는 이중구조팬의 소음특성을 알아보고 소음저감 방법으로 알려진 톱니형 뒷전(Serrated Trailing Egde)을 적용하여 이중구조팬의 소음을 저감시켰다. 해석에는 Lattice Boltzmann Method(LBM)를 이용한 비정상 전산해석을 수행하였으며 해석의 타당성을 평가하기 위하여 시험을 실시하였다. 이중구조팬은 일반적인 팬처럼 단일의 Blade Passing Frequency(BPF)를 갖는 것이 아니라 내부팬과 외부팬 각각의 BPF가 서로 다른 음역대에서 나타나는 것을 확인 하였다. 톱니형 뒷전을 내부팬에 적용하여 경계층에서의 구속와류와 뒷전에서의 와류흘림이 억제 또는 분산되고 광역소음뿐만 아니라 팬의 토크도 저감되었다.

• 한국소음진동공학회논문집
• /
• 제17권1호
• /
• pp.41-47
• /
• 2007

Scattering fields of two dimensional acoustic waves by a circular cylinder are investigated. The present numerical approach for the acoustic scattering problem has difficulties of numerical robustness, long-time stability and suitability of far-field boundary treatments. The time-dependent periodic acoustic source is used to analyze Interference patterns between incident waves and waves reflected by the cylinder. Characteristic boundary algorithms coupled with 4th order Modified-Flux-Approach ENO(essentially non-oscillatory) schemes are employed in generalized coordinates to examine the effect of the wane frequency on the interference patterns. Non-reflecting boundary conditions, which is crustal for accurate computations of aeroacoustic problems, are used not to contaminate scattering fields by reflected waves at the outer boundary. Computed scattering fields show the circumferential acoustic modes generated by interacting between acoustic sources and scattered waves. At a lower frequency, the wave passes almost straight through the cylinder without Interacting with circular cylinder. Simulation results are presented and compared with the analytic solution. Computed RMS-pressure distribution on the cylinder wall is good agreement with exact solution.

• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.590-598
• /
• 2003

A computational aero-acoustic (CAA) method is used to predict the tonal noise generated from a cavity of automobile door seals or gaps at low flow Mach numbers (A$\_$$\infty$/=0.077 and 0.147) In the present method, the acoustically perturbed Euler equations are solved with the acoustic source term obtained from the unsteady incompressible Navier-Stokes calculations of the cavity flow in self-sustained oscillations. The aerodynamic and acoustic fields are computed for the Reynolds numbers based on the displacement thickness, Re$\_$$\delta$*/=850 and 1620 and their fundamental mode characteristics are investigated. The present method is also verified with the experimentally measured sound pressure level (SPL) spectra.

• 대한기계학회논문집B
• /
• 제25권9호
• /
• pp.1157-1164
• /
• 2001

Centrifugal fans are widely used and the noise generated by these machines causes one of the most serious problems. In general, the centrifugal fan noise is often dominated by tones at BPF(blade passage frequency) and its higher harmonics. This is a consequence of the strong interaction between the flow discharged from the impeller and the cutoff in the casing. However, only a few research have been carried out on predicting the noise because of the difficulty in obtaining detailed information about the flow field and casing effects on noise radiation. The objective of this study is to understand the generation mechanism of sound and to develop a prediction method for the unsteady flow field and the acoustic pressure field of a centrifugal fan. We assume that the impeller rotates with a constant angular velocity and the flow field of the impeller is incompressible and inviscid. So, a discrete vortex method(DVM) is used to model the centrifugal fan and to calculate the flow field. The force of each element on the blade is calculated by the unsteady Bernoulli equation. Lowsons method is used to predict the acoustic source. In order to compare the experimental data, a centrifugal impeller and wedge introduced by Weidemann are used in the numerical calculation and the results are compared with the experimental data. Reasonable results are obtained not only for the peak frequencies but also for the amplitudes of the tonal.