• 열처리공학회지
• /
• 제16권3호
• /
• pp.134-140
• /
• 2003

Effects of cryogenic treatment and tempering temperature on the amount of retained austenite, hardness and wear properties has been investigated using alloy tool steel, STD 11. Cryogenic treatments were performed at the temperatures of $-100^{\circ}C$, $-150^{\circ}C$ and $-196^{\circ}C$, and tempering were performed at $200^{\circ}C$ and $530^{\circ}C$. It was shown that lower hardness value was obtained on high temperature ($530^{\circ}C$) tempering even after cryogenic treatment. And retained austenite was not entirely transformed to martensite after cryogenic treatment even at $-196^{\circ}C$, which was not consistent with the belief that $-80^{\circ}C$ was sufficient to entirely transform any austenite retained in the quenched microstructure. Austenite retained in cryogenic treated condition was completely transformed to martensite only after tempering at $530^{\circ}C$. As far as wear test conditions in this investigation, it was found that cryogenic treatments improved the sliding wear resistance, but improvement of wear resistance was not directly related with retained austenite contents. And it was found that predominent wear mechanisms of STD 11 steel were oxidation wear and adhesive wear In sliding wear conditions.

• 열처리공학회지
• /
• 제28권4호
• /
• pp.190-199
• /
• 2015

The study is intended to investigate the effect of solution treatment on microstructure and corrosion behavior of AZ91(Mg-9%Al-1%Zn-0.3%Mn)-2%Ca casting alloy. In as-cast state, the AZ91-2%Ca alloy consisted of intermetallic ${\beta}(Mg_{17}Al_{12})$, $Al_8Mn_5$ and $Al_2Ca$ phases in ${\alpha}-(Mg)$ matrix. After the solution treatment, Al within the ${\alpha}-(Mg)$ matrix was distributed more homogeneously, along with the slight decrease in the total amount of intermetallic compounds. The corrosion resistance of the AZ91-2%Ca alloy was improved after the solution treatment. The microstructural examinations for the solution-treated samples revealed that the better corrosion resistance may well be related to the incorporation of more oxides and hydroxides such as $Al_2O_3$, $Al(OH)_3$, CaO and $Ca(OH)_2$ into the surface corrosion product without dissolution of the intermetallic phases along the grain boundaries.

• 환경위생공학
• /
• 제17권4호
• /
• pp.29-38
• /
• 2002

Advanced oxidation of wastewater was studied with a purpose to remove TOC and color by the ozone-assisted Fenton reaction. The optimal conditions were determined by hydrogen peroxide and ozone concentrations. Experimental results indicate that the ozone treatment after Fentons process was found to provide very efficient removal efficiency in the process, avoiding the exclusive ozone treatment. The combined process of ozone in the Fenton oxidation respectively was increased removal efficiences of 10.7％ in comparison with exclusive Fenton oxidation. Also, the treatments of ozone after Fenton's oxidation respectively had increased the removal efficiences of 16.％. As a result, the treatment of ozone after Fentons oxidation had the best removal efficiency of approximately 96％. Removal efficiency of color was significantly increased as mush as 26％ by the advanced Fenton's oxidation in comparison with exclusive Fenton's oxidation. The removal efficiencies in the biological treatment using Bacillus subtilis after Fenton's oxidation and after Fenton's and ozone's oxidation were increased by 14％ and 19％ respectively. Although these combined Bacillus subtilis-assisted Fenton's oxidation was determined to be effective method to treat the dyeing wastewater in an economic point of view, the choice of wastewater treatment can be varied depending on water quality.

• 한국물환경학회지
• /
• 제33권1호
• /
• pp.63-69
• /
• 2017

Small size privately owned wastewater treatment plants have been difficult to treat their wasted sludge and maintain steady effluent quality compared with publicly owned wastewater treatment plants. Therefore, this study has focused on treatment efficiency enhancement, specially nitrogen removal efficiency by recycling dewatering filtrate as an alkalinity additive from filter press using $CaCO_3$. As the result, it was found that the optimal mixing ratio between the excess sludge and $CaCO_3$ was 1:2. The major operation parameters such as specific substrate utilization rate, specific nitrification rate, and specific denitrification rate were also improved 64% ($0.048-0.079mg\;BOD_5/mg\;MLVSS{\cdot}day$), 35% ($0.020-0.027mg\;NH_3-N/mg\;MLVSS{\cdot}day$) and 68% ($0.051-0.086mg\;NO_3{^-}-N/mg\;MLVSS{\cdot}day$), respectively, after the adoption of new methods. Therefore, both the problem of sludge treatment at small scale plants and the need for efficiency improvement could be solved.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 somma/kms meeting
• /
• pp.185-185
• /
• 2003

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 추계학술대회 초록집
• /
• pp.176-176
• /
• 2009

• 환경생물
• /
• 제31권4호
• /
• pp.302-307
• /
• 2013

Microbial fermented cellulose gel, citrus gel (CG), was successfully fabricated to porous foam by radiation treatment and freeze drying. The chemically induced radiation was used to create highly porous foam and further freeze drying of the CG produced tough foams with interconnected open pores for use in tissue engineering. The microstructure of the CG foam was controlled by varying the irradiation dose and quenching temperature with pore size ranging from several microns to a few hundred microns. Tensile strength and Gurley value of the CG foam were influenced by irradiation dose. These radiation induced CG foams are promising scaffolds for tissue engineering.

• 열처리공학회지
• /
• 제19권1호
• /
• pp.50-59
• /
• 2006

• 자원리싸이클링
• /
• 제29권1호
• /
• pp.35-42
• /
• 2020

최근 인체 유해성이 높은 석면 함유 제품의 다량 폐기로 인해 석면 함유 폐기물(asbestos-containing waste: ACW)이 계속해서 발생하고 있으며, 매립지 부족 등의 이유로 석면 무해화 및 재활용 기술 개발이 요구되고 있다. 마이크로웨이브를 이용한 열처리는 석면 함유 폐기물 무해화에 가장 효율적인 방법이나 석면이 상온에서 마이크로웨이브를 흡수하지 않는 한계점을 가지고 있다. 본 연구에서는 상온에서 마이크로웨이브를 흡수하여 발열하는 무기 발열체인 SiC 플레이트 사이에 석면 함유 폐기물를 위치시킨 상태에서 마이크로웨이브 열처리를 진행하는 방법으로 석면 함유 폐기물를 무해화 하였다. 효율적인 열처리를 위하여 석면 함유 폐기물를 파쇄 및 분쇄 공정을 통해 분말화하여 무해화 열처리 실험을 진행 하였으며, 열처리 조건에 따른 무해화 특성을 파악하기 위하여 마이크로웨이브 열처리 온도와 시간 변수를 조절하였다. 열처리 후 석면 함유 폐기물는 XRD와 SEM을 이용한 결정구조 및 미세구조 분석을 통하여 무해화 특성을 분석 하였다. SiC 플레이트를 적용한 마이크로웨이브 열처리 방법은 단시간 내에 목표 온도까지 가열이 가능하며 최종적으로 1,200℃에서는 60분 이상, 1,300℃에서는 10 분 이상의 마이크로웨이브 열처리를 진행하였을 때 결정구조와 미세구조상에서 석면이 완전히 제거되는 것을 확인하였다.

• 대한금속재료학회지
• /
• 제50권4호
• /
• pp.316-323
• /
• 2012

The aim of this study is to investigate the effect of post heat treatment on bonding properties of roll cladded Ti/MS/Ti materials. First grade Ti sheets and SPCC mild steel sheets were prepared and then Ti/MS/Ti clad materials were fabricated by a cold rolling and post heat treatment process. Microstructure and point analysis of the Ti/MS interfaces were performed using the SEM and EDX Analyser. Diffusion bonding was observed at the interfaces of Ti/MS. The thickness of the diffusion layer increased with post heat treatment temperature and the diffusion layer was verified as having $({\epsilon}+{\zeta})+({\zeta}+{\beta}-Ti)$ intermetallic compounds at $700^{\circ}C$ and an $({\zeta}+{\beta}-Ti)$ intermetallic compound at $800^{\circ}C$, respectively. The micro Knoop hardness of mild steel decreased with post heat treatment temperature; however, those of Ti decreased at a range of $500{\sim}600^{\circ}C$ and showed a uniform value until $800^{\circ}C$ and then increased rapidly up to $900^{\circ}C$. The micro Knoop hardness value of the diffusion layer increased up to $700^{\circ}C$ and then saturated with post heat treatment. A T-type peel test was used to estimate the bonding forces of Ti/Mild steel interfaces. The bonding forces decreased up to $800^{\circ}C$ and then increased slightly with post heat treatment. The optimized temperature ranges for post heat treatment were $500{\sim}600^{\circ}C$ to obtain the proper formability for an additional plastic deformation process.