• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.5C
• /
• pp.171-185
• /
• 2011

Ready-mixed shotcrete that mixed with high quality aggregate and can improve construction quality is produced in a dry mortar plant and transported to construction sites. Because of using aggregate that produced in a special plant, Ready-mixed shotcrete has many advantages : good grain-size distribution, minimum stone powder, high quality and standardization material, etc. In this basic study different from the existing study that limited to additive and accelerator, the improvement of aggregate quality was tried to upgrade the shotcrete performance. The investigation about the construction conditions of shotcrete was performed and the result of an opinion poll was analyzed for a good grasp of the problems in domestic shotcrete quality. Pilot Plant Test was also performed to minimize the material segregation in plant manufacturing process. In additions, the field test was performed to find the optimum contents of synthetic fiber, appearing the same flexible toughness with that of steel fiber, and to find the optimum replacement ratio of blast furnace slag.

• Journal of Community Nutrition
• /
• v.4 no.3
• /
• pp.187-194
• /
• 2002

This study was investigated the effects of exercise and supplementation of L-carnitine and antioxidants on hepatic mitochondrial function, especially oxidative phosphorylation (OXPHOS). Isolated hepatic mitochondria from 4 rat groups were functionally tested by an analysis of respiration and the coupling of this process to ATP synthesis in the presence of ADP. Four groups were non-trained, non-supplemented group (NTNS), non-trained, supplemented group (NTS), long term-trained, non-supplemented group (LTNS) , and long term-trained, supplemented group (LTS). The trained rats run on a treadmill (grade 10°,20 m/min) for 60min/day for 8 weeks. The supplemented rats were treated with L-carnitine (0.5% diet), vitamin E(0.5mg/g BW), vitamin C (0.5mg/g BW) and melatonin (1 $\mu$ g/g BW) for 8 weeks. There were exercise effects on improving mitochondrial OXPHOS. Within non-supplemented groups, exercised rats resulted in a significant decrease in state 4 oxygen consumption, which increased the respiratory control (RC) ratio and ADP : O (P/O) ratio. There were supplementation effects on improving mitochondrial OXPHOS, too. Within non-exercised rats, supplemented rats resulted in a significant decrease in state 4 oxygon consumption. which increased the RC ratio and P/O ratio. There were additive effects of exercise and supplementation on OXPHOS. Within supplemented rats, exercise resulted in an increase in RC ratio. Significant effects of exercise-supplement interaction on improving OXPHOS were identified. It suggests that exercise and supplementation of L-carnitine and antioxidants might improve more efficiently the impaired OXPHOS efficiency in mitochondrial dysfunction that recognized as is an important cause of degenerative diseases. (J Community Nutrition 4(3) : 187∼194, 2002)

• Journal of the Korean Society of Radiology
• /
• v.2 no.4
• /
• pp.33-40
• /
• 2008

Images acquired by a digital X-ray imaging system are inherently degraded due to system degradation process and additive noise sources. The system degradation in image quality is typically described as the system response function characterized by the modulation transfer function (MTF) and the noise term described as the noise power spectrum (NPS). In this case, we can restore the blur image as close as possible to the original image by using modified filtering designed for digital imaging system, as we know more precisely about the MTF and the NPS. In this paper, by performing simulation, we tried to restore blurred images taken from a digital X-ray imaging system based upon conventional filtering techniques such as a direct-inverse filtering, limited-inverse filtering, or a Wiener filtering, and evaluated the characteristics of the image restoration.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.316-316
• /
• 2010

Thin films spin-coated from solvent solutions are characterized by solution parameters and spin-coating process. In this study, performance characteristics of polymer solar cells were investigated with changing solution parameters such as solvent and additives. The phase-separation between polymer and fullerene is needed to make the percolation pathway for better transportation of hole and electron in polymer solar cells. For this reason, cooperative effects of solvent mixtures adding additives with distinct solubility have been studied recently. In this study, chlorobezene, 1, 2-dichlorbenzene, and chloroform were used as solvent. 1, 8-diiodoctaned and 1, 8-octanedithiol were used as additives and were added into poly(3-hexylthiophene-2, 5-diyl)/[6, 6]-phenyl C61 butyric acid methyl ester (P3HT/PCBM) blends. Pre-patterned ITO glass was cleaned using ultrasonication in mixed solvent with ethyl alcohol, isopropyl alcohol and acetone. PEDOT:PSS was spin-coated on to the ITO substrate at 3000rpm and was baked at $120^{\circ}C$ for 10min on the hotplate. The prepared solution was spin-coated at 1000rpm and the spin-coated thin film was dried in the Petri dishes. Al electrode was deposited on the thin film by thermal evaporation. The devices were annealed at $120^{\circ}C$ for 30min. By adding 2.5 volume percent of additives into the chlorobenzene from that bulk heterojunction films consisting of P3HT/PCBM, the power efficiency (AM 1.5G conditions) was increased from 2.16% to 2.69% and 3.12% respectively. We have investigated the effect of additives in P3HT/PCBM blends and the film characteristics and the film characteristics including J-V characteristics, absorption, photoluminescence, X-ray diffraction, and atomic force microscopy to mainly depict the morphology control by doping additives.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.163-172
• /
• 2006

This study evaluated the laboratory properties of asphalt binder and mixture modified with SPC(Sulfur Polymer Cement), which consists of sulfur as a main ingredient that is an industrial by-product made from refining process of crude oil and carbon-black as an additive. Four levels of SPC modifier ratios(0, 10, 30, 50%) were evaluated in the laboratory. Superpave(Superior Performing Asphalt Pavements) system was used to determine the PG(Performance Grade) and evaluate the property of SPC modified binder at the different temperatures. IDT(Indirect Tensile Test) was performed to evaluate the resistance of fatigue and low-temperature cracking at $10^{\circ}C\;and\;-10^{\circ}C$. Wheel-tracking test was also performed to evaluate the rutting-resistance of SPC modified asphalt mixtures. Test results showed that the more SPC modifier ratios, the better rutting-resistance and the more potential of low-temperature cracking resistance. However, SPC modifier did not show the effect on the fatigue cracking resistance.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.25 no.2
• /
• pp.156-165
• /
• 2015

Objectives: The purpose of this study was to investigate the possible effects of a gasoline vapor recovery system on personal exposure levels of gasoline vapor constituents including benzene, toluene, ethyl benzene, xylene(BTEX), and methyl tert-butyl ether(MTBE) among gas station workers in a metropolitan area. Methods: Thirty-one gas station workers at ten gas stations in a metropolitan area were selected as subjects for this study. Test method PV2028 as recommended in the OSHA process was used for sampling and analysis. Results: The personal exposure levels of benzene, toluene, ethyl benzene, xylene, MTBE and gasoline vapor in the gas station workers were $0.0018{\pm}0.0069ppm$, $0.0077{\pm}0.0137ppm$, $0.0002{\pm}0.0008ppm$, $0.0016{\pm}0.0084ppm$, $0.2619{\pm}0.3340ppm$, and $1.4940{\pm}1.7984ppm$, respectively. After adjustment for refueling frequency and volume, personal exposure levelswere higher in the gas stations where gasoline vapor recovery systems(Stage II) were not installed, but the results were not statistically significant. Gasoline vapor concentrations showed a positive correlation to the level of MTBE, a gasoline additive. Conclusions: Vapor recovery systems(Stage II) were effective not only in reducing emissions of air pollutants, but also in reducing exposure to hazardous substances among gas station workers. In addition, acorrelation between gasoline vapors and MTBE concentration was confirmed.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.1
• /
• pp.109-120
• /
• 2013

As information-oriented industry has been developed and electronic devices has come to be smaller, lighter, multifunctional, and high speed, the components used to the devices need to be much high density and should have find pattern due to high integration. Also, diverse reliability problems happen as user environment is getting harsher. For this reasons, establishing and securing products and components reliability comes to key factor in company's competitiveness. It makes accelerated test important to check product reliability in fast way. Out of fine pattern failure modes, failure of Electrochemical Migration(ECM) is kind of degradation of insulation resistance by electro-chemical reaction, which it comes to be accelerated by biased voltage in high temperature and high humidity environment. In this thesis, the accelerated life test for failure caused by ECM on fine pattern substrate, $20/20{\mu}m$ pattern width/space applied by Semi Additive Process, was performed, and through this test, the investigation of failure mechanism and the life-time prediction evaluation under actual user environment was implemented. The result of accelerated test has been compared and estimated with life distribution and life stress relatively by using Minitab software and its acceleration rate was also tested. Through estimated weibull distribution, B10 life has been estimated under 95% confidence level of failure data happened in each test conditions. And the life in actual usage environment has been predicted by using generalized Eyring model considering temperature and humidity by developing Arrhenius reaction rate theory, and acceleration factors by test conditions have been calculated.

• Clean Technology
• /
• v.5 no.2
• /
• pp.45-52
• /
• 1999

Recycling of red mud from the aluminium manufacturing process was investigated to be utilized as plastic fillers. High density polyethylene(HDPE), low density polyethylene(LDPE) and polypropylene(PP) were found to be the suitable plastic material for which red mud can be used as fillers. With the addition of red mud the plastic showed red brown color. As the ratio of amount of red mud to plastic increased, the tensile strength increased while the Izod impact strength decreased. About five percent of ethylene vinyl alcohol(EVA) was needed as an additive to prevent the lowering of impact strength. Maleic anhydride modified polypropylene was effective for reduction of impact strength lowering of PP. Mixed waste plastics containing LDPE, HDPE, PP, polystyrene and ABS could also accommodate red mud as fillers. In this case, significant loss in mechanical properties were observed due to immiscibility between the components. Ethylene propylene rubber(EPR) and styrene butadiene styrene block copolymer (SBS) could be used to improve the impact properties of the commingled waste plastics.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.22-28
• /
• 2017

The result of stripping process for the removal of the post etch/ash Photoresist (PR) residue on an aluminum patterned wafer by using supercritical $CO_2$ ($sc-CO_2$) mixture, was investigated by scanning of electron microscope (SEM) inspection of wafer, measuring the cloud points and visual observation of the state of $sc-CO_2$ mixtures. It was found that $sc-CO_2$ mixtures were made by mixing additives and $sc-CO_2$ should form homogeneous and transparent phase (HTP) in order to effectively and uniformly remove the post etch/ash PR residue on the aluminum patterned wafer using them. The additives were formulated by mixing and co-solvents like an amine compound and fluorosurfactants used as HTP agents, and the PR residue on the wafer were able to be rapidly and effectively removed using the $sc-CO_2$ mixture of HTP. The five kinds of additives were formulated by the recipe of mixing co-solvents and surfactants, which were able to remove PR residue on the wafer by mixing with $sc-CO_2$ at the stripping temperature range from 40 to $80^{\circ}C$. The five kinds of $sc-CO_2$ mixtures which were named as PR removers were made, which were able to form HTP within the above described stripping temperature. The cloud points of $sc-CO_2$ mixtures were measured to find correlation between them and HTP.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.359-368
• /
• 2007

The copolymer membranes, poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) were prepared by phase inversion method using as an additive with N,N-dimethylformamid as a solvent. The pores are generated during the solvent and non-solvent exchange process in the coagulation bath filled with non-solvent (distilled water). The highest porosity of the membrane was 60%. The surface and cross-section of the membranes was observed with a scanning electron microscopy (SEM). The mechanical property of the membrane was determined by using an universal testing machine (UTM). Tensile strength of measured membranes is presented the maximum 6.57 MPa at 30 wt% of PVdF-HFP.