• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.7.2-7.2
• /
• 2007

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1995.11a
• /
• pp.102-102
• /
• 1995

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.10a
• /
• pp.171-171
• /
• 1997

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.11a
• /
• pp.56-56
• /
• 2002

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.166-168
• /
• 2006

$Si_3N_4/SiC$ composite ceramics was sintered in order to investigate their bending strength behavior after crack healing. $Y_2O_$ and $TiO_2$ power was added as sintering additives to enhance it's sintering property. A three-point bending specimen was cut out from sintered plates. About $100\;{\mu}m$ semi-circular surface cracks were made on the center of the tension surface of the three-point bending specimen using Vickers indenter. After the crack-healing processing from $500^{\circ}C$ to $1300^{\circ}C$, for 1 h, in air, the bending strength behavior of these crack-healed specimen coated with $SiO_2$ colloidal were determined systematically at room temperature. $Si_3N_4/SiC$ ceramics using additive powder ($Y_2O_3+TiO_2$) was superior to that of additive powder $Y_2O_3$. The additive powder $TiO_2$ exerted influence at growth of $Si_3N_4$. The optimum crack healing conditions coated $SiO_2$ colloidal were $1000^{\circ}C$ at $Si_3N_4/SiC$ using additive powder ($Y_2O_3+TiO_2$), and $1300^{\circ}C$ at $Si_3N_4/SiC$ using additive powder $Y_2O_3$.

• Journal of the Korean Ceramic Society
• /
• v.44 no.4 s.299
• /
• pp.189-193
• /
• 2007

Effect of additive composition on fracture toughness of in situ-toughened $SiC-Si_3N_4$ composites was investigated for five different additive compositions. The highest toughness $(6.4MPa{\cdot}m^{1/2})\;in\;SiC-Si_3N_4$ composites investigated herein was obtained when an Y-Mg-Si-Al-O-N oxynitride glass was used as a sintering additive. The improvement in fracture toughness was produced by enhanced bridging and deflection by $Si_3N_4$ grains.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.238-239
• /
• 2005

With the aim of developing XLPE insulation for extra high voltage cable, we investigated the morphology of cross-linked polyethylene. We used a kind of base materials and additives, and controlled curing condition and amount of additives. The effect of addition of additives on morphology of XLPE such as lamellar density, orientation and additive layer were analyzed using TEM analysis. We applied this result to diffused additive amount was analyzed using FT-IR analysis, and the change of microstructure as the degree of additive diffusion was analyzed using TEM analysis.

• Journal of Powder Materials
• /
• v.29 no.1
• /
• pp.22-27
• /
• 2022

Conventionally, metal materials are produced by subtractive manufacturing followed by melting. However, there has been an increasing interest in additive manufacturing, especially metal 3D printing technology, which is relatively inexpensive because of the absence of complicated processing steps. In this study, we focus on the effect of varying powder size on the synthesis quality, and suggest optimum process conditions for the preparation of AlCrFeNi high-entropy alloy powder. The SEM image of the as-fabricated specimens show countless, fine, as-synthesized powders. Furthermore, we have examined the phase and microstructure before and after 3D printing, and found that there are no noticeable changes in the phase or microstructure. However, it was determined that the larger the powder size, the better the Vickers hardness of the material. This study sheds light on the optimization of process conditions in the metal 3D printing field.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.4
• /
• pp.8-13
• /
• 1986

To investigate effect of sericite on pilot Fourdrinier paper making for loading, with respectively 15% additive sericite on talc, we made newprint with TMP, and then tested sericite on talc, we made newprint with TMP, and then tested sericite and talc abrasion, physical and strength properites of the paper. Consequently, as a loading materials, sericite had outstanding properties different from talc from the result of this paper; 1. Sericite was a good loading materials because the quantity of abrasion was small. 2. Sericite had a good physical properties of Foudrinier paper because brightness. ash content and water absorption were high. 3. Newsprint paper strengthes of additive talc were nigher than those of additive sericite.

• Journal of Welding and Joining
• /
• v.34 no.4
• /
• pp.9-16
• /
• 2016

Metal parts are produced by conventional methods such as casting, forging and cutting, extrusion, etc. However, nowadays, with additive manufacturing (AM), it is possible to directly commercialize by means of stacking of equipment to the 3D drawing and use of high precision tools such as laser source. Thus, drawing of materials is an important aspect in delivering good products. AM deals with production of lighter aircraft parts and few more three-dimensional molds, it wish to manufacture special medical parts and want to steadily expand the new market area. The cost of related equipment and materials are still expensive and difficult to obtain on a mass production. However, the ability to make changes and lead the innovation in the paradigm of traditional manufacturing process is still effective. In this paper, we introduce metal AM and the principles of the related devices, metal powder production process, and their application.