• Asian-Australasian Journal of Animal Sciences
• /
• 제30권7호
• /
• pp.994-998
• /
• 2017

Objective: An experiment was conducted to determine the effect of superdosing phytase on productive performance and egg quality in laying hens. Methods: A total of 200 42-wk-old Hy-Line Brown laying hens were allotted into 1 of 5 dietary treatments with 5 replicates consisting of 8 hens per replicate. The positive control (PC) and negative control diets (NC) were prepared based on the recommended P levels in layer diets. Supplemental phytase was added to the negative control diet at 10,000 (SD10), 20,000 (SD20), or 30,000 (SD30) fytase units (FTU)/kg. Productive performance was summarized for 6 weeks from 42 weeks to 47 weeks of age. Egg quality was assessed from 4 eggs per replicate randomly collected at the conclusion of the experiment. Results: The SD20 treatment had greater (p<0.05) hen-day egg production than PC, NC, and SD10 treatment groups. There was no difference in hen-day egg production between SD20 and SD30 treatment groups. However, SD30 treatment had greater (p<0.05) hen-day egg production than PC treatment, but showed no difference in hen-day egg production as compared to NC and SD10 treatment groups. However, egg weight, egg mass, feed intake, and feed conversion ratio were not affected by dietary treatments. Egg quality including eggshell strength, eggshell color, egg yolk color, and haugh unit was not influenced by dietary treatments. Conclusion: Superdosing level of 20,000 FTU/kg phytase in diets has a positive effect on egg production rate, but no beneficial effect on egg quality in laying hens.

• Carbon letters
• /
• 제11권1호
• /
• pp.28-33
• /
• 2010

In this study, $TiO_2$-Activated carbon (AC) complex fibers were prepared by electrospinning for the synergetic effect of adsorption and degradation of organic pollutant. The average diameter of these fibers increased with increasing the amount of AC added, except for 1AC-TOF (AC$/TiO_2$ =1/40 mass ratio). After calcinations at $500^{\circ}C$, long as-spun fibers were broken and their average diameter was slightly decreased. The resultant fibers after calcination had rough surface and sphere shapes like a peanut. From XRD results, it was confirmed that as-spun fibers were changed to anatase $Ti_O2$ fiber after calcinations at $500^{\circ}C$. The prepared $TiO_2$-AC complex fibers could remove procian blue dyes by solar light irradiation with high removal property of 94~99%. The PB dye was rapidly removed by adsorption during the initial 5 minutes. But after 5 minutes, dye removal was occurred by photodegradation. In this study, the most efficient AC/$TiO_2$ ratio of $TiO_2$-AC complex fibers was 5/40, showing the synergetic effect of adsorption and photodegradation. It is expected that the $TiO_2$-AC complex fibers can be used to remove of organic pollutants in water system.

• Structural Engineering and Mechanics
• /
• 제37권6호
• /
• pp.671-684
• /
• 2011

Deciding on an optimal sensor placement (OSP) is a common problem encountered in many engineering applications and is also a critical issue in the construction and implementation of an effective structural health monitoring (SHM) system. The present study focuses with techniques for selecting optimal sensor locations in a sensor network designed to monitor the health condition of Dalian World Trade Building which is the tallest in the northeast of China. Since the number of degree-of-freedom (DOF) of the building structure is too large, multi-modes should be selected to describe the dynamic behavior of a structural system with sufficient accuracy to allow its health state to be determined effectively. However, it's difficult to accurately distinguish the translational and rotational modes for the flexible structures with closely spaced modes by the modal participation mass ratios. In this paper, a new method of the OSP that computing the mode shape matrix in the weak axis of structure by the simplified multi-DOF system was presented based on the equivalent rigidity parameter identification method. The initial sensor assignment was obtained by the QR-factorization of the structural mode shape matrix. Taking the maximum off-diagonal element of the modal assurance criterion (MAC) matrix as a target function, one more sensor was added each time until the maximum off-diagonal element of the MAC reaches the threshold. Considering the economic factors, the final plan of sensor placement was determined. The numerical example demonstrated the feasibility and effectiveness of the proposed scheme.

• 한국재료학회지
• /
• 제28권2호
• /
• pp.108-112
• /
• 2018

The present study demonstrates the effect of raw powder on the pore structure of porous W-Ni prepared by freeze drying of camphene-based slurries and sintering process. The reduction behavior of $WO_3$ and $WO_3-NiO$ powders is analyzed by a temperature programmed reduction method in Ar-10% H2 atmosphere. After heat treatment in hydrogen atmosphere, $WO_3-NiO$ powder mixture is completely converted to metallic W without any reaction phases. Camphene slurries with oxide powders are frozen at $-30^{\circ}C$, and pores in the frozen specimens are generated by sublimation of the camphene during drying in air. The green bodies are hydrogen-reduced at $800^{\circ}C$ and sintered at $1000^{\circ}C$ for 1 h. The sintered samples show large and aligned parallel pores to the camphene growth direction, and small pores in the internal wall of large pores. The strut between large pores, prepared from pure $WO_3$ powder, consists of very fine particles with partially necking between the particles. In contrast, the strut densification is clearly observed in the Ni-added W sample due to the enhanced mass transport in activation sintering.

• 대한조선학회논문집
• /
• 제52권1호
• /
• pp.25-33
• /
• 2015

Following the previous works on the natural frequency of heaving circular cylinder, i.e. Lee and Lee (2013) and Kim and Lee (2013), an investigation of the same spirit on the 2-dimensional cylinder of Lewis form has been conducted. As before, the natural frequency is defined as that corresponding to the local maximum of the MCFR (Modulus of Complex Frequency Response), which is given by the equation of motion in the frequency domain analysis. Hydrodynamic coefficients were found by using the Ursell-Tasai method, and numerical results for them were obtained up to much higher frequencies than before, for which the method was known as numerically unstable in the past. For a wide range of H, the beam-draft ratio, and ${\sigma}$, the sectional area coefficient, including their practical ranges for a ship, results for the natural frequency were computed and presented in this work. Two approximate values for the natural frequency, one proposed by Lee (2008) and another one by the damped harmonic oscillator, were also compared with the current results, and for most cases it was observed that the current result is between the two values. Our numerical results showed that the values of the local maximum of MCFR as well as the natural frequencye increase as ${\sigma}$ increases while H decreases. At present, extension of the present finding to the 3-dimensional ship via the approximate theory like the strip method looks promising.

• 설비공학논문집
• /
• 제17권4호
• /
• pp.312-317
• /
• 2005

The objectives of this paper are to study the absorption characteristics of $NH_3$ bubbles in the binary nanofluids and to quantify the effects of surfactants and nano-particles on the bubble absorption performance. 2-Ethyl-1-Hexanol, n-Octanol, and 2-Octanol are used as the surfactants and nano-sized $Al_{2}O_3$ and Cu particles are added to make the binary nanofluids into $NH_3/H_{2}O$ solution. The concentration of $NH_3$ solution ($x_s$), the concentration of surfactants ($x_{SA}$), and the mass fraction of nano-particles ($w_{np}$) are considered as key parameters. The experimented ranges of $x_s,\;x_{SA},\;and\;w_{np}$ are $0{\sim}17.92\%,\;0{\sim}1,500\;ppm\;and\;0{\sim}0.2\%$, respectively. The absorption rates are calculated by measuring initial and final weights of test section and exposed time. In addition, the bubble absorption processes are visualized using the shadow graphic method. The results show that the absorption performance is significantly enhanced up to 4 times by adding the surfactants and up to 3 times in the binary nanofluids.

• 한국재료학회지
• /
• 제8권12호
• /
• pp.1082-1089
• /
• 1998

$YBa_2$$Cu_3$$O_{7-y}$ (123) 초전도체에서 은 입자의 미세분산을 얻고자 말릭산을 사용한 발화합성과 고상반응법으로 123와 123-Ag 복합 초전도분말을 제조하였다. 발화합성분말을 원료로 사용할 시 마이크론 미만의 미세한 123 분말과 은 분말의 복합체를 얻을 수 있었다. 원료로 사용된 산화은($Ag_2O$) 분말은 발화합성과정 중금속 은으로 환원되었다. 원료분말에 첨가된 금속 은에 의한 반응 물질간의 확산 촉진으로 123상이 단시간내에 생성되었고 입자성장도 촉진되었다. 발화합성법으로 제조한 시편은 기계적 혼합공정으로 제조한 시편에 비해 은 입자들은 미세하게 분산시킬 수 있어서 초전도체의 임계전류밀도가 향상되었다.

• 생명과학회지
• /
• 제25권7호
• /
• pp.780-785
• /
• 2015

전복을 4일간 굶긴 후 phlorotannin-고함유 곰피를 제공하여 이의 섭취 및 phlorotannin 축적정도를 조사하였다. 전복의 성장속도는 곰피 혹은 일반 사료로 쓰이는 다시마를 20일간 투여한 경우 서로 비슷하였다. 주된 phlorotannin 성분인 7-phloroeckol 및 eckol은 역상 HPLC로서 측정하였다. 7-phloroeckolol은 섭취 6일만에 전복 건조육 1g당 0.58±0.13 mg 정도 축적되었다. Eckol은 6일만에 전복 건조육 1g당 0.25±0.05 mg 정도 축적되었으며 실험기간 내 그 정도를 유지하였다. 대조군로서의 다시마 투여 전복은 phlorotannin을 전혀 함유하지 않았다. Phlorotannin은 전복 조직내에서의 구성효소들에 의하여 분해되어 지는것으로 보인다. 그러므로 다양한 생리활성을 지닌 phlorotannin 물질들을 가진 고부가 가치의 전복 생산은 전복수확 6일전부터 간단히 사료만 phlorotannin-고함유 곰피로 바꾸어 공급함으로서 생산가능하다.

• Applied Biological Chemistry
• /
• 제41권5호
• /
• pp.331-336
• /
• 1998

김치공장에서 배출되는 배추 절임폐수를 이용한 효모 균체 생산을 위하여 절임폐수에서 생육이 우수한 Pichia guilliermondii A9를 분리하여 생육특성을 조사하였다. 이 균주는 pH 3부터 pH 8 범위에서 생육이 양호하고 NaCl의 농도가 10%까지는 생육저해를 받지 않는 내염성을 나타내었으며 24시간 배양 후 절임폐수의 BOD가 약 90% 제거되었다. 그러나, 절임폐수에서는 생산된 균체량이 낮은 편이었으므로 P. guilliermondii A9의 생육 증가를 위하여 절임폐수에 암모니움염, 인산염 및 철, 망간 등을 첨가하였으나 효과를 얻지 못하였다. 한편, 김치공장에서 다량 발생되어 문제가 되고 있는 배추 쓰레기의 착즙액을 첨가한 결과 첨가량에 비례하여 균체량이 크게 증가하여 배추 쓰레기와 절임폐수를 동시에 효모 균체 생산의 기질로 이용할 수 있는 가능성을 보여 주었다.

• 한국항해항만학회지
• /
• 제36권5호
• /
• pp.379-385
• /
• 2012

본 논문에서는 수상 및 수중운동체의 안정성 및 안정화기법에 관해 고찰한다. 선박이 운동을 하게 되면 부가질량이 변하게 되고 대칭인 시스템행렬이 비대칭이 된다. 비대칭성에 따라 시스템의 안정성해석방법도 달라지는데 예를 들어 가속도 피드백을 통해 비대칭요소를 제거하여 대칭으로 변환시키는 것이 가장 대표적인 해석 및 안정화 기법이다. 시스템 모델자체는 어디까지나 모델이기 때문에 대상시스템을 명확하게 수식으로 표현할 수 없으므로 피드백에 의한 비대칭요소를 소거시키는 방법은 타당하지 못하다. 따라서 본 논문에서는 대칭행렬이 비대칭행렬로 변하는 제약에 구애받지 않는, 보다 일반성을 갖는 안정성해석법을 제안하였다. 그리고 시스템 안정성 조건을 행렬부등식으로 변환하여 나타내었다. 이것은 안정성 해석 및 안정화를 위한 제어이득을 효율적으로 계산할 수 있는 방법으로 다양한 제약조건에도 유연하게 대응할 수 있다. 시뮬레이션을 통해 제안한 기법의 유효성을 검증하였다.