• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1172-1175
• /
• 1992

The conventional adaptive hysteresis band current control technique has disadvantages such that on-line calculation of the hysteresis band is very complex, therefore, the adaptive hysteresis band must be stored in the look-up table. In this paper, a new simplified adaptive hysteresis band current control technique with phase decoupling is presented. The adaptive band is independent of the back EMFs. Using this adaptive band and the phase decoupled current error, the modulation frequency is fixed at nearly constant and the PWM inverter has optimal switching pattern.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.2
• /
• pp.529-538
• /
• 2015

Due to the high efficiency and compact mechanical structure, direct drive variable speed generators are used for power conversion in wind turbines. The wind energy conversion system (WECS) considered in this paper consists of a permanent magnet synchronous generator (PMSG), uncontrolled rectifier, dc-dc boost converter controlled with maximum power point tracking (MPPT) and adaptive hysteresis controlled voltage source inverter (VSI). For high utilization of the converter's power capability and stabilizing voltage and power flow, constant DC-link voltage is essential. Step and search MPPT algorithm which senses the rectified voltage ($V_{DC}$) alone and controls the same is used to effectively maximize the output power. The adaptive hysteresis band current control is characterized by fast dynamic response and constant switching frequency. With MPPT and adaptive hysteresis band current control in VSI, the DC link voltage is maintained constant under variable wind speeds and transient grid currents respectively.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.171-174
• /
• 1991

Among the various PWM methods, the hysteresis-band current control PWM method is popularly used because of its simplicity of implementation, fast response characteristics and inherent peak current limiting capability. However, the current control PWM method with a fixed hysteresis-band has the disadvantage that switching frequency decreases and current ripple is high as the increasing of back-EMF. As a result, load current contains excess harmonics. This paper describes a adaptive hysteresis-bandwidth control algorithm so as to maintain the average switching frequency constant and decrease the current ripple where the hysteresis bandwidth is derived as a relation with the switching frequency. This control algorithm is applied to the surface-type brushless DC motor with separated winding and using the computer simulation, the validity of its algorithm is proved.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.615-623
• /
• 2016

The paper describes a hysteretic buck converter including a differentiator and an adaptive hysteresis window controller. Differentiating the feedback signal achieves ultra-fast switching of the buck converter. The adaptive hysteresis window control allows a monotonous operation with predictable noise spectrum, and gives way to efficient design for variable supply and output voltages. The measurement results in a $0.13-{\mu}m$ CMOS process indicated that the switching frequency became double times higher, and the voltage ripple was reduced by up to 69%. They also indicated that the normalized switching frequency variation was reduced by 74% with variable $V_{DD}$ and by 63% with variable $V_{OUT}$. The power efficiency was improved by 3.5% depending on loading condition.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.382-387
• /
• 1998

The adaptive hysteresis band current control method using neural network is proposed to hold the switching frequency of PWM inverter constant at any operating points of ac motor. The adaptive hysteresis band equation is derived as the teaching signal of neural network. and then the structure and learning algorithm of the neural network a are suggested. The simulation results show that the switching frequency of PWM inverter is held constant at any operating conditions of ac motor and the proposed method has good transient performance of stator current.

• Bulletin of the Korean Mathematical Society
• /
• v.38 no.1
• /
• pp.29-53
• /
• 2001

This note presents a an indirect adaptive control scheme for first-order continuous-time systems. The estimated plant model is controllable and then the adaptive scheme is free from singularities. The singularities are avoided through a modification of the estimated plant parameter vector so that its associated Sylvester matrix is guaranteed to be nonsingular. That properties is achieved by ensuring that the absolute value of its determinant does not lie below a positive threshold. A modification scheme based on the achievement of a modified diagonally dominant Sylvester matrix of the parameter estimates is also given as an alternative method. This diagonal dominance is achieved through estimates modification as a way to guarantee the controllability of the modified estimated model when a controllability measure of the ‘a priori’ estimated model fails. In both schemes, the use of a hysteresis switching function for the modification of the estimates is not required to ensure the nonsingularity of the Sylvester matrix of the estimates.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2001.11a
• /
• pp.181-185
• /
• 2001

This paper presents a digitally speed sensorless control system for induction motor with direct torque control (DTC). The drive is based on Mode1 Reference Adaptive System (MRAS) using state observer as a reference model fat flux estimation. The system are closed loop stator flux and torque observer for wide speed range that inputs are currents and voltages sensing of motor terminal, model reference adaptive control (MRAS) with rotor flux linkages for the speed turning aignal at low speed range, two hysteresis controllers. The Proposed system is verified through simulation.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.249-253
• /
• 2004

This paper presents an implementation of position control system of Switched Reluctance Motor (SRM) using digital hysteresis controller. Although SRM possess several advantages including simple structure and high efficiency, the control drive system using power semiconductor device is required to drive this motor. The control drive system increases overall system cost. To overcome this problem and increase the application of SRM, it is needed to develope the servo drive system of SRM. So, the position control system of 1 Hp SRM is developed and evaluated by adaptive switching angle control. The position/speed response characteristics and voltage/current waveforms are presented to prove the capability of SRM for a servo drive application. Moreover, digital hysteresis current controller is developed and evaluated by experimental testing for the purpose of system developmental cost reduction.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.3
• /
• pp.110-115
• /
• 2002

This paper proposes the adaptive fuzzy control system using the microprocessesor for high precision control of automation systems which exist non-linearities such as saturation, relays, hysteresis, and dead zones. The proposed system which provides the improvement in terms of the control region in transient and adaptive control, first used the frequence-locked mothed driving a system to generate a output voltage proportional to the frequency diffierence of relnence input signal and feedback signal for fast transient response,, and when the error reaches the preset value, used the adaptive fuzzy logic for precision control. The theoretical and experimental studies have been carried out. The presented results from the above investigation show considerable improved performance in the precision control of servo control systems.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.549-559
• /
• 2019

This paper proposes an adaptive sliding mode control (ASMC) strategy with an enhanced optimal reaching law (EORL) for the robust current tracking control of the boost converter based hybrid power source (HPS) in an electric vehicle (EV). A conventional ASMC strategy based on state observers and the hysteresis control method is used to realize the current tracking control for the boost converter based HPS. Then a novel enhanced exponential reaching law is proposed to improve the ASMC. Moreover, an enhanced exponential reaching law is optimized by particle swarm optimization. Finally, the adaptive control factor is redesigned based on the EORL. Simulations and experiments are established to validate the ASMC strategy with the EORL. Results show that the ASMC strategy with the EORL has an excellent current tracking control effect for the boost converter based HPS. When compared with the conventional ASMC strategy, the convergence time of the ASMC strategy with the EORL can be effectively improved. In EV applications, the ASMC strategy with the EORL can achieve robust current tracking control of the boost converter based HPS. It can guarantee the active and stable power distribution for boost converter based HPS.