• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.647-654
• /
• 2007

A Discrete continuation Method/homotopy approaches are studied for energy/fuel optimal low thrust Earth escape trajectory by solving a two point boundary value problem(TPBVP). Recently, maneuvers using low thrust propulsion system have been identified as emerging technologies. The low thruster is considered as the main actuator for orbit maneuvers. The cost function consists of a energy/fuel consumption function, and constraints are position and velocity vectors at the terminal escape point. Solving the minimum energy/fuel problem directly is not an easy task, so we adopt the homotopy analysis. Using a solution of the minimum energy, which is solved by discrete continuation method, we obtain the solution of the minimum fuel problem.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.11
• /
• pp.981-988
• /
• 2016

Dynamometer is a device for testing the performance of the brake and it is composed of a test zone, the mechanical inertia zone, the electric motor and the control zone. Hybrid dynamometer is a way to compensate for the loss of mechanical inertia in accordance with the brake operation by using an electric motor to reduce the size of the mechanical inertia with the advantage that can be tested in the relatively small size of the mechanical inertia and low cost. In this paper, design the proper size of hybrid dynamometer in the laboratory level with the space constraints, analysed the effect of critical parameter on the braking performance of hybrid dynamometer such as changing the friction coefficient. With this study, could get the results of guideline to judge the poor friction material by measuring the torque of the electric motor to compensate the energy loss due to a reduced mechanical inertia.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.165-172
• /
• 1998

The electromechanical energy conversion conditioning and processing implementation in USM direct motion control system is generally divided into two power stages: the two-phase high-frequency ac power inversion stage for driving piezoelectric ceramic PZT transducer array off the USM stator and the mechanical thrust power conversion stage based on the frictional force between the piezo electric stator array and the rotary slider of the USM. However, the dynamic and steady-state mathematical modeling of the USM is extremely default from a theoretical point of view because it contains many complicated an nonlinear characteristics dependant on operation temperature. In +2$0^{\circ}C$~3$0^{\circ}C$, the operating characteristics of the USM has represented normal condition. But the other temperature, it has abnormal condition so that driving frequency, current and motor speed will be down. The recent USM has controller without temperature compensation. This study represents the fuzzy controller for speed compensation according to operating temperature by driving frequency.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1048-1053
• /
• 2005

This paper presents design and integration of the ROBHAZ-DT3, which is a newly developed mobile robot system with chained double-track mechanisms. A passive adaptation mechanism equipped between the front and rear body enables the ROBHAZ-DT3 to have good adaptability to uneven terrains including stairs. The passive adaptation mechanism reduces energy consumption when moving on uneven terrain as well as its simplicity in design and remote control, since no actuator is necessary for adaptation. Based on this novel mobile platform, a rescue version of the ROBHAZ-DT3 with appropriate sensors and a semi-autonomous mapping and localization algorithm is developed to participate in the RoboCup2004 US-Open: Urban Search and Rescue Competition. From the various experiments in the realistic rescue arena, we can verify that the ROBHAZ-DT3 is reliable in traveling rugged terrain and the proposed mapping and localization algorithm are effective in the unstructured environment with uneven ground. The another application is an military robot for an EOD(Explosive Ordnance Disposal) and reconnaissance mission. The military version of the ROBHAZ-DT3 with a water disrupter, a thermal scope and a long distance wireless communication device is developed and sent to the area of military tactics in Iraq. Consequently, the feasibility of the military version of ROBHAZ-DT3 is verified.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.301-304
• /
• 2008

This paper presented an structural efficiency of steel coupling beam jointed single plate shear connections with seat and top angle. Parameters for the test specimens were are seat and top angle, reinforcing of concrete, embedded length, section loss. Steel coupling beam with angle showed excellent strength, stiffness, energy dissipation capacity. The specimen with no reinforcement around the embedded steel plate showed slightly low deformation capacity because of early failure in the precast concrete walls. However, the specimen with reinforcement around the embedded steel plate showed good deformation capacity. Deformation capacity was not decrease despite short embedded length. The specimen with section loss showed excellent deformation capacity. Because shear strength of steel coupling beam was lesser than of connections. These results showed that for workability and cost efficiency, the proposed system is promising for one of steel coupling beam.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.6
• /
• pp.251-257
• /
• 2014

An actuator system is a type of motor designed to control a mechanism operated by a source of energy, in the form of an electric current by converting energy into some kind of motion. As audio actuators, transforming electric voltage signal into audio signal, speakers and amplifiers are commonly used. In applications of industry, high output power systems are required. For these systems to generate high-quality output, it is essential to control output impedance of audio systems. We have developed an adaptable power supply for driving active amplifier systems with variable loads. Depending on the changing values of resistance of the speaker which produces audible sound by transforming electric voltage signal, the power supply source of the active amplifier can generate the maximum power delivered to the speaker by an adaptable change of loads. The amplifier is well protected from the abrupt increment of peak current and an excess of current flow.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.7
• /
• pp.706-712
• /
• 2014

The inverters used to drive Brushless DC motors (BLDC) include switching devices such as FETs and the faults in FETs cause severe performance degradation in systems where a BLDC acts as actuator. This paper presents a fault detection and isolation method for the FETs of an inverter for BLDC motor control systems, which is based on the EKF (Extended Kalman filter). Firstly, an equivalent circuit model for a BLDC motor plus its inverter system was derived. Secondly, a state-space equation was established, where the on-resistance of the FETs is expressed as a state variable and the EKF equation estimates the on-resistance. If the estimated resistance differs greatly from the known value, it can be asserted that there is a fault on that FET. Thirdly, the local convergence of the established EKF was proved. Finally, through the experiments, the performance of the proposed method was verified. The results show that the on-resistance is estimated close to the value specified in the FET data sheet in normal operation, whereas the estimated resistance is a much larger value than the normal one in case an FET fault occurs. Therefore, it is confirmed that the proposed fault detection and isolation method works appropriately in real systems.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.5
• /
• pp.563-569
• /
• 2015

A chemical reaction occurring in CSTR (Continuous Stirred Tank Reactor) is significantly affected by the concentration, temperature, pressure, and reacting time of materials, and thus it has strong nonlinear and time-varying characteristics. Also, when an existing linear PID controller with fixed gain is used, the performance could deteriorate or could be unstable if the system parameters change due to the change in the operating point of CSTR. In this study, a technique for the design of a fuzzy PD plus I controller was proposed for the temperature control of a CSTR process. In the fuzzy PD plus I controller, a linear integral controller was added to a fuzzy PD controller in parallel, and the steady-state performance could be improved based on this. For the fuzzy membership function, a Gaussian type was used; for the fuzzy inference, the Max-Min method of Mamdani was used; and for the defuzzification, the center of gravity method was used. In addition, the saturation state of the actuator was also considered during controller design. The validity of the proposed method was examined by comparing the set-point tracking performance and the robustness to the parameter change with those of an adaptive controller and a nonlinear proportional-integral-differential controller.

• Smart Structures and Systems
• /
• v.19 no.3
• /
• pp.309-322
• /
• 2017

In this paper, the buckling, and free vibration analysis of tapered functionally graded carbon nanotube reinforced composite (FG-CNTRC) micro Reddy beam under longitudinal magnetic field using finite element method (FEM) is investigated. It is noted that the material properties of matrix is considered as Poly methyl methacrylate (PMMA). Using Hamilton's principle, the governing equations of motion are derived by applying a modified strain gradient theory and the rule of mixture approach for micro-composite beam. Micro-composite beam are subjected to longitudinal magnetic field. Then, using the FEM, the critical buckling load, and natural frequency of micro-composite Reddy beam is solved. Also, the influences of various parameters including ${\alpha}$ and ${\beta}$ (the constant coefficients to control the thickness), three material length scale parameters, aspect ratio, different boundary conditions, and various distributions of CNT such as uniform distribution (UD), unsymmetrical functionally graded distribution of CNT (USFG) and symmetrically linear distribution of CNT (SFG) on the critical buckling load and non-dimensional natural frequency are obtained. It can be seen that the non-dimensional natural frequency and critical buckling load decreases with increasing of ${\beta}$ for UD, USFG and SFG micro-composite beam and vice versa for ${\alpha}$. Also, it is shown that at the specified value of ${\alpha}$ and ${\beta}$, the dimensionless natural frequency and critical buckling load for SGT beam is more than for the other state. Moreover, it can be observed from the results that employing magnetic field in longitudinal direction of the micro-composite beam increases the natural frequency and critical buckling load. On the other hands, by increasing the imposed magnetic field significantly increases the stability of the system that can behave as an actuator.

• Journal of Fisheries and Marine Sciences Education
• /
• v.9 no.2
• /
• pp.167-178
• /
• 1997

It has been expected not only for crew but also for passengers to realize a ship whose rolling and other motions are small as much as possible. Restricting our consideration to the roll reduction, the conventional roll stabilization system, fins or anti-rolling tanks hve been utiized as the actuator. Excessive motions would interfere with the recreational activities of passengers on a cruise ship. Often more than half of the load of a containership is stowed above deck where it is subjected to large acclerations due to rolling. In some situations this may cause some internal damage to the contents of the containers; in more severe situations failure of the lashing can occur and containers may be lost over-board. Underdeck cargo in ordinary cargo ships and bulk commodities in colliers, ore ships and grain ships can shift if the motions become too severe. The purpose of this study is to concentrate on the additions. either internal or external to the hull, that reduce or otherwise improve the motion responses of the hull. It is assumed that the additions are such that their benefit to the motions of the ship outweights any impact on the ability of the ship to perform its assigned task. It is particularly challenging to obtain large improvements in the motion characteristics of existing ships that are being rebuilt or modified for some task not anticipated in their original design. Further the authors will statistically analyze the influence of ruder-roll-yaw coupling motion in the case of application of this advanced control method to various kinds of ship.