• 설비공학논문집
• /
• 제1권1호
• /
• pp.32-45
• /
• 1989

The airflow characteristics of clean tunnel type clean room were experimentally investigated with the change of operating speed and exit type. Distributions of air velocity and pressure were measured in clean room which is located lower than HEPA filters, and the pressure distribution was also measured in upper plenum which is located above the HEPA filters, to identify the performance of clean room. Through the analysis it was turned out that air velocity characteristics in clean room were significantly affected by the upper plenum flow conditions such as pressure distribuion. This results will be useful in the actual clean room design to enhance the performance.

• 대한기계학회논문집B
• /
• 제33권1호
• /
• pp.9-16
• /
• 2009

This paper is the second of 2 companion papers which investigate in-cylinder swirl generation characteristics in helical port engine with wide valve angle. Two wide valve-angle engines, which are same ones and have slightly different rig swirl number, were used to compare the characteristics of cylinder-flow. One intake port is deactivated to induce swirl flow. A PIV (Particle Image Velocimetry) was applied to measure in-cylinder velocity field during intake stroke. The results show that the intake flow component passing through valve area near the cylinder wall is not negligible in helical port engine with wide valve angle contrary to conventional one. The effect of this velocity component on in-cylinder increases as the swirl ratio rises and compression process progresses. Consequently, this component destroys in-cylinder swirl flow completely during compression resulting in no actual swirl at the end stage of compression.

• 대한기계학회논문집B
• /
• 제32권10호
• /
• pp.761-768
• /
• 2008

This paper is the first of 2 companion papers which investigate in-cylinder swirl generation characteristics in helical port engine with wide valve angle. Two wide valve-angle engines, which are same ones and have slightly different rig swirl number, were used to compare the characteristics of cylinder-flow. One intake port is deactivated to induce swirl flow. A PIV (Particle Image Velocimetry) was applied to measure in-cylinder velocity field during intake stroke. The results show that the intake flow component passing through valve area near the cylinder wall is not negligible in helical port engine with wide valve angle contrary to conventional one. The effect of this velocity component on in-cylinder increases as the swirl ratio rises and intake process progresses. Consequently, this component interferes the formation of in-cylinder swirl flow resulting in lower actual swirl.

• 한국연소학회지
• /
• 제18권3호
• /
• pp.54-60
• /
• 2013

This paper shows a general development process for aircraft gas turbine combustors. As a first step for developing the preliminary combustor design program, several combustor sizing methodologies using reference area concepts are reviewed. There are three ways to determine the reference area; 1) combustion efficiency approach, 2) pressure loss approach, 3) velocity assumption approach. The current study shows the comparisons of the calculated results of combustor reference values from the pressure loss and velocity assumption approaches. Further works are required to add iterative steps in the program using more reasonable values of pressure loss and velocities, and to evaluate the sizing results using data for actual combustor performance and sizes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.151-157
• /
• 2004

In this paper, we propose a simple control scheme, based on second order sliding modes, which guarantees a fast and precise container transfer and the swing suppression during the container movement, despite of model uncertainties and unmodeled dynamic actuators. In the actual case, the swing suppression is obtained by constraining the system motion on a suitable surface which involves both the desired path and the swing angle. Strictly speaking, the trolley velocity is modified on-line, on the actual swing angle, to obtain the suppression of the oscillations not only at the end of the transport but during transfer as well. Such controller has been tested on a laboratory-size model of the 3Dcrane, and some experimental results are reported.

• 한국자동차공학회논문집
• /
• 제7권6호
• /
• pp.49-56
• /
• 1999

The effects of the internal flow in a D.I. Diesel injection nozzle on the atomization of a spray were analyzed experimentally. Flow visualization studies were made using a transparent acrylic model nozzle as a diesel nozzle . Water instead of disel fuel was used as the injection liquid. The geometry of the model nozzle was scaled up 10 times of the actual nozzle and the injection pressure for the model nozzle was adjusted so as to achieve a Reynolds number at the discharge hole that was the same as the actual nozzle. Experimental results show that when the needle lift was small, the high turbulence in the sac chamber generated by the high velocity seat flow made the spread angle of the spray plume large. Cavitation, which arose from the sac chamber, makes the spread angle of the spray plume large but the discharge coefficient small.

• 한국방재학회 논문집
• /
• 제1권2호
• /
• pp.75-83
• /
• 2001

본 연구에서는 자연형하천으로 정비된 소하천의 실태조사를 통해 정비현황의 문제점을 조사하였다. 수원천 수계에 포함된 창사천을 대상으로 현장관측을 실시하였다. 창사천에서 관측된 강우량, 유속, 수심 등의 자료를 이용하여 운동파 모형의 적용성을 평가하였으며, 실무에서 널리 사용되고 있는 SCS, Clark, RRL 모형과도 비교하였다. 운동파방정식을 창사천유역에 적용했을 때 실측치와 비교적 유사한 결과를 얻을 수 있었다.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.273-279
• /
• 2008

The purpose of this study is not only to evaluate thermal performance but also to find the stress behavior of heat transfer tubes under the part load operation in Heat Recovery Steam Generator. Flow analysis was performed to know the behavior of exhaust gas from gas turbine and thermal performance was calculated using distribution of hot exhaust velocity. In addition, tubes temperature during operation were gathered from actual plant to verify the uneven flow distribution under part load operation. Stress analysis was performed using tubes temperature data gathered from actual plant under both part and full load operations to know the stress behavior of tubes.

• 천문학회지
• /
• 제45권5호
• /
• pp.111-116
• /
• 2012

We present a mathematical model that predicts the variation of illuminance during a solar eclipse, considering continuous effects of limb darkening. We assume that (1) the Sun and the Moon constitute perfect spheres, (2) the Moon crosses the Sun with a constant apparent velocity, and (3) sunspots, prominences, and coronae can be neglected. We compare predictions of this model with actual measurements made by M$\ddot{o}$llmann & Vollmer (2006) during a total solar eclipse in Turkey, and with predictions of existing models. The new model is shown to describe the actual phenomenon more accurately than existing models.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1988년도 한국자동제어학술회의논문집(국제학술편); 한국전력공사연수원, 서울; 21-22 Oct. 1988
• /
• pp.921-927
• /
• 1988

The process and results of computer simulation using bond graphs for a hydraulic system driving large rotational inertia are presented in this paper. As the large rotational inertia and its application characteristics, control criteria of this system is not position-control nor velocity-control but appropriate acceleration, deceleration and inching ability. All the components' nonlinear characteristics are modelled using bond graphs. The equationing and solution process is carried out by a package. Finally it is concluded that modelling of this kind of system by bond graphs and using a software as its solver shows good approximated results to actual experimental data, and that the proposed modelling may be useful to actual design process for this kind of hydraulic system.