• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2766-2768
• /
• 2003

In this paper, positions of microphones and speakers in adaptive noise control systems are selected using optimization techniques. To get the optimal control characteristics of adaptive noise control system, It is necessary to optimize positions of microphones and speakers. Assume that control speakers are placed in a experimental enclosure several place indoors. Acoustic transfer functions from control speaker positions to microphone positions are measured for simulation program by experiments, and simulated annealing methods are used to select optimal positions of speakers and microphones.

• Journal of Sensor Science and Technology
• /
• v.19 no.5
• /
• pp.337-341
• /
• 2010

In this work, the nanocrystalline ZnO/polycrystalline(poly) aluminum nitride(AlN)/ Si-layered structure was fabricated for humidity sensor applications based on surface acoustic wave(SAW). The ZnO film was used as a sensitive material layer. The ZnO and AlN(0002) were deposited by a sol-gel process and a pulse reactive magnetron sputtering, respectively. The ZnO sensitive films coated on AlN have a hexagonal wurtzite structure after the thin films annealed at $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$. The surface of the film exhibits sponginess and a nanometer particle size(below 50 nm). The largest shift in the frequency response was at approximately 200 kHz(the relative humidity: 10 %~90 %) for the structure annealed at $400^{\circ}C$. The effect of the change in the environmental temperature on the frequency response of the SAW humidity sensor was also investigated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.38-46
• /
• 1995

In this paper, an experimental study on the effects of the impact damage and the perforation characteristic of CFRP laminates with different fiber stacking orientation and ply number was done through an observation of interrelations between the impact energy vs. transmitted energy and the impact energy vs. absorbed energy per unit volume. The velocities of the ball before or after impact are measured by the high-speed camera. And when CFRP laminates are subjected to tranverse impact by a steel ball(${\phi}10$), the delamination shapes generated by impact damage are observed by using SAM (Scanning acoustic Microscope).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.204-210
• /
• 2003

A PC-based analysis and design system of exhaust muffler is described. It makes use of software packages such as Sysnoise and STAR-CD to calculate transmission loss(TL) and back pressure. The system is applied to redesign a main muffler of passenger car to improve its performance. The effects of design parameters on acoustic and pressure loss characteristics are examined. Taguchi method Is used to determine optimal combination of parameters which affects muffler performances such as TL and back pressure. Three models are chosen and compared in laboratory bench test and engine dynamometer test to prove their performances.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.910-915
• /
• 2003

This paper describes the design of a 2-phase stepping motor driver using CPLD(Complex Programmable Logic Device). The driver IC such as L297 (SGS-Thomson Microelectronics), which is mostly used has some problems in PWM control because of the switching noise of power MOSFETs. It causes current ripple and acoustic noise. To improve theses characteristics, we proposed a new current control method that the output PWM frequency is almost constant using a digital filter. Also we proposed constant current method for 1-2 phase(half step) excitation. The proposed method is implemented with CPLD(Xilinx, XC9572-PC44). Experimental results show the effectiveness of the proposed method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.246-248
• /
• 2005

본 논문은 23kV 가스절연개폐기에서의 윤활제 고착시 발생되는 현상을 조사하였다. 내부 개폐접점부의 마찰저항을 줄이고 가동전극의 윤활한 동작을 위해 사용되는 그리스 (grease)를 과다하게 도포할 경우 고착과 함께 가동전극의 미끄럼운동에 영향을 주는 것이 확인되었다. 영향 평가로는 물성시험과 투 개방 음향특성을 분석하였다. 본 논문의 결과는 개폐장치의 제조품질 개선 및 정전감소에 기여할 것으로 사료된다.

• Journal of Mechanical Science and Technology
• /
• v.20 no.2
• /
• pp.197-204
• /
• 2006

The purpose of this study is to evaluate the AE characteristics for the basemetal, PWHT (post-weld heat treatment) and weldment specimens of SA-516 steel during fracture testing. Four-point bending and AE tests were conducted simultaneously. AE signals were emitted in the process of plastic deformation. AE signal strength and amplitude of the weldment was the strongest, followed by PWHT specimen and basemetal. More AE signals were emitted from the weldment samples because of the oxides, and discontinuous mechanical properties. AE signal strength and amplitude for the basemetal or PWHT specimen decreased remarkably compared to the weldment because of lower strength. Pre-cracked specimens emitted even lower event counts than the corresponding blunt notched specimens. Dimple fracture from void coalescence mechanism is associated with low-level AE signal strength for the basemetal or PWHT. Tearing mode and dimple formation were shown on the fracture surfaces of the weldment, but only a small fraction produced detectable AE.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.196-201
• /
• 1997

In point of noise and vibration, it is easy to occur a noise and vibration, because the reciprocal compressor is composed of crank shaft, rod piston and etc. Therefore, it is important to understand the mechanism of reciprocal compressor. In this study, we measured the sound pressure level of compressor. There are two dominent frequencies. The first of one results from the suction part. In suction process, the suction valve flutteres, and it produces the noise of the first frequency. The other results from the structural vibration of the shell resonated by discharge pipe. Thus, to reduce the noise of compressor, it will be most efficiency to redesign muffler for the first frequency and discharge pipe for the second frequency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.400-405
• /
• 2005

The diagnosis of mechanical load and of power transmission system failures is usually carried out through mechanical signals such as vibration signals, acoustic emissions, motor speed envelope. If the mechanical load comes from an electrical machine the mechanical failures could be detected previously. Mechanical rotor imbalances and rotor eccentricities are reflected in electric, electromagnetic and mechanical quantities. Therefore, many surveillance schemes apply to the Fourier spectrum of a line current in order to monitor the motor condition. Due to the interaction of the currents and voltages, both these current harmonics are also reflected by a single harmonic component in the frequency spectrum of the electric power. Motor Current Signature Analysis is the usuful technique to assess machine electrical condition.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.3
• /
• pp.200-206
• /
• 2010

In ultrasound-excited thermography, the injected ultrasound to an object is transformed to heat and the appearance of defects can be visualized by thermography camera. The advantage of this technology is selectively sensitive to thermally active defects. Despite the apparent simplicity of the scheme, there are a number of experimental considerations that can complicate the implementation of ultrasound excitation thermography inspection. Factors including acoustic horn location, horn-crack proximity, horn-sample coupling, and effective detection range all significantly affect the detect ability of this technology. As conclusions, the influence of coupling pressures between ultrasound exciter and specimen was analyzed, which was dominant factor in frictional heating model.