• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.67-72
• /
• 1993

Wall wetting phenomenon in the intake port of an MPI engine was investigated with different kinds of injectors by an A/F step response test and analysis was done based on the simple wall wetting model to find out a certain correlation between wall wetting and A/F variations. It was found that (1) At fully warmed condition of 90.deg.C water temperature, around 40-60% of injected fuel was wall wetted, (2) At cold condition of 45.deg.C Water temperature, around 68-80% of injected fuel was wall wetted, and (3) A/F variations during acceleration and deceleration were influenced by the wetting area, the fuel droplet size, and the amount of wall wetting fuel.

• International Journal of Aeronautical and Space Sciences
• /
• v.5 no.1
• /
• pp.75-82
• /
• 2004

Nowadays, many kinds of research for airship have being studied withincrease of interests in airship. But these make little progress even now. In flighttest, the data acquisition from the actual flight test has lots of difficulties becausethe airship dynamic response is slow and sensitive to extemal environment. In thispaper, through the actual flight test, appropriateness of the mathematical dynamicmodel was presented by showing the test results in various conditions. Thetuming, the acceleration, and the deceleration motions were tested and analyzed.

• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.72-77
• /
• 2016

Although the initial cost of permanent-magnet linear synchronous motors is high owing to the installation of armatures over the full length of the transportation lines, linear motors are useful for transportation systems because of their high speed, acceleration, and deceleration. For these reasons, research into reducing the cost of linear motors is necessary, and a stationary distributed-armature system has been suggested for installing armatures in sections where acceleration and deceleration of the mover are required. However, each armature has ends that significantly increase the cogging force, resulting in the increase in the thrust ripple of the mover. Therefore, in order to improve the thrust ripple of the system, the present study aims to provide auxiliary teeth on both ends of the armature to achieve an optimal design through an analysis of the contribution ratio with respect to factors regarding the design of the experiment and the objective function.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.119-124
• /
• 2005

Decision of operation performance mode to minimize the energy consumption of urban rail vehicle. This paper analyses how much acceleration and deceleration of urban rail vehicle should be applied andhow to choose an operation mode to minimize energy consumption when train runs between station within the fixed operation time. The decided operation pattern satisfying the minimum energy consumption becomes a target trajectory and a basis for the controller design criteria. To make this goal it grasps the characteristics of urban rail vehicle, realize operation energy model of urban rail vehicle and verify the accuracy of embodied model the Matlab simulation with the same operation result of real route. It searches for operation pattern to minimize operation energy by changing the acceleration and deceleration on the imaginative route and proposes operation pattern minimizing energy consumption by applying real operation data between Dolgogee-Sukgye section of Seoul Metropolitan Subway Line 6.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.269-274
• /
• 2004

It is important to decide the minimum film thickness and viscosity variations of a multigrade lubricant in the contact surface under the high pressure conditions. By carrying out acceleration, deceleration, and various sliding-rolling ratio movement between two contact bodies, it is experimented that film formation variations in the contact surface are captured with multigrade lubricants in order to exactly investigate the variations of film formations. Optical interference images are continuously captured with high resolution CCD camera during the captured period of acceleration, deceleration. The friction forces between the contacting bodies are also measured simultaneously with the film formation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.801-805
• /
• 2000

This paper presents a new method of tool path optimization. A NC verification model based Z-map was utilized to obtain chip load in feed per tooth. This developed software can regenerate a NC program from cutting condition and the NC program that was generated in CAM. The regenerated NC program has not only all same data of the ex-NC program but also the new feed rates in every block. The new NC data can reduce the cutting time and manufacture precision dies with the same chip load in feed per tooth. This method can also prevent tool chipping and make constant tool wear. This paper considered the effects of acceleration and deceleration in feed rate change.

• Journal of Korean Orthopaedic Sports Medicine
• /
• v.2 no.2
• /
• pp.113-118
• /
• 2003

Throwing motion divided by 6 phases such as wind-up, (early and late) cocking, acceleration, deceleration, follow-through. Overuse injuries in baseball result most often from pitching. Poor mechanics is the leading cause of arm injuries. The purpose of this article is to analyze the each joint motion and evaluate the biomechanics and pathomechanics during pitching.

• ETRI Journal
• /
• v.37 no.2
• /
• pp.328-337
• /
• 2015

This paper applies acceleration/deceleration control-based velocity profiles to an infeed control algorithm for a cross-belt-type sorting system to improve the accuracy and performance of the system's infeed. The velocity profiles are of a trapezoidal shape and often have to be modified to ensure that parcels correctly synchronize with their intended carriers. Under the proposed method, an infeed line can handle up to 5,600 items/h, which indicates a 40% increase in performance in comparison with its existing handling rate of 4,000 items/h. This improvement in performance may lead to a reduction in the number of infeed lines required in a sorting system. The proposed infeed control algorithm is applied to a cross-belt-type sorting system (model name: SCS 1500) manufactured by Vanderlande Industries.

• Journal of the Korean Society for Railway
• /
• v.9 no.6 s.37
• /
• pp.682-688
• /
• 2006

In this paper, a method which can deduce the traction farce or the braking force from the acceleration or the deceleration of the train, has been suggested. In the case of Korean high speed train (HSR-350x), the traction force and the braking forces have been obtained by using this method. It is proven that the proposed method is a very good tool in estimating the traction force or the braking force when the train starts or stops. Also, these forces on be used to calculate friction coefficients of mechanical brakes and the transmission efficiency of the traction system.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.69-80
• /
• 2007

The purpose of this study was to investigate the difference of ground reaction forces of swimming athletes during their starting motion and to find out the most effective starting motions which were used in swimming athletes. The subjects were 9 male and 8 female high school swimming athletes who were athletic career over 7 years and used three starting motions in competition. The ground reaction forces were measured from each athletes performing three starting motion each of the open grap starting motion, closed grap starting motion and track starting motion. For the measurement, the force platform of AMTI company was utilized, and the analysis on measured ground reaction forces were used of Biosoft(Ver. 1.0). The items measured were stance time, Fz max deceleration force and Fz max deceleration force time, Fz mid stance force and Fz mid stance force time, Fz max acceleration force and Fz max acceleration force time, Torque maximum and Torque maximum time, Torque average, Excursion along Y axis of center of pressure of foot, Excursion along X axis of center of pressure of foot, Length of center of pressure of foot, Average velocity of center of pressure of foot. The data measured by the closed grap starting motion, open grap starting motion and track starting motion were analyzed by one-way repeated ANOVA. The results were as follows ; 1. The Fz max deceleration force time, Fz mid stance force, Fz max acceleration force, Torque maximum and Torque maximum time, Excursion along Y axis of center of pressure of foot, Average velocity of center of pressure of foot were significantly fast and large in the closed grap starting motion then open grap starting motion and track starting motion. 2. The Excursion along Y axis of center of pressure of foot was significantly long in the closed grap starting motion then open grap starting motion and track starting motion.