• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.5
• /
• pp.63-71
• /
• 2010

This paper is about a research of steam curing which is one of the curing methods for accelerating the early-age strength of pre-cast concrete. With cylinder mold and mock-up specimen, the research was executed to study the best cycle of steam curing temperature through quantifying cycle of steam curing and maximum temperature, while the required strength is developed under the early-age. Moreover, causes and measurements for the high temperature of concrete, which is due to the steam curing, and the crack, which occurs when removing steel form, are stated. Ultimately, the economical method of producing, which satisfies early-age strength development and quality assurance while manufacturing PC structure, is stated.

• Journal of the Korean Society of Tobacco Science
• /
• v.20 no.1
• /
• pp.19-25
• /
• 1998

The bulk curing experiment to the improve the quality of flue-cured leaves were carried out to evaluate relationship between cyclic curing and conventional curing method. We studied the effect of the cyclic change of wet bulb temperature at the yellowing stage of flue curing on chemical properties of cured leaves. The wet bulb temperature was automatically controlled between preset high($38^{\circ}C$) and low point ($35^{\circ}C$) everyone hour cyclically during 12 hours after starting luring. As a result, the acceleration of the increase in the chemical properties of cured leaves were observed. As to the chemical properties, there was decreased in citric acid, increased in malic acid of the nonvolatile organic acids and all higher fatty acids content of leaves cured by this method compared with in that of conventional curing method, while a major chemical compounds in relation to aromatic essence of cigarette smoke in essential oil components of lured leaves was mostly higher in this method than those of conventional ones, and it was evaluated that there was decreased in CO, TPM, Tar, and $CO_2$ content of the cigarette smoke comparing to the conventional luring method.

• Journal of the Korean Society of Tobacco Science
• /
• v.20 no.1
• /
• pp.13-18
• /
• 1998

In the flue curing process, the wet bulb temperature is usually controlled at a constant level. To improve the quality of flue cured leaves, we studied the effect of the cyclic change of wet bulb temperature at the yellowing stage of flue curing on physical properties of cured leaves. The wet bulb temperature was automatically controlled between preset high (38℃) and low point (35℃) every one hour cyclically. As a result, the acceleration of the increase in the physical properties of cured leaves were observed. The leaves cured by this method were more or less orange in color, better bodied, and less brittle compared with the leaves produced by conventional curing. However, the leaves cured by this method had a little sharpness and harshness. As to the physical properties, there was decreased in occurrence of flat leaves than that of conventional ones. On the other hand, in case of cyclic curing method, increase of price per kg reached to 2-3% compared with those of conventional ones.

• Restorative Dentistry and Endodontics
• /
• v.26 no.2
• /
• pp.127-133
• /
• 2001

There are several factors affecting the effectiveness of polymerization of the esthetic restorative materials. Among those factors, the initiator. camphoroquinone has the unique characteristic. of which the light sensitivity is very dependent on the wavelength of blue light. Camphoroquinone shows the most light absorption ability in the wavelength range of 470nm. So most of clinically used light curing systems adopt this phenomenon as their polymerization mechanism. The most popular way of light curing system is standard 40 second curing. But the problem of standard curing technique shows the rapid increase of resin viscosity followed by the acceleration of polymerization and the limited resin flow, resulted in reduction of the physicalproperty of restoration by retained stress. The object of this study was to verify the effects of narrow-banded wavelength on the microhardness of the esthetic restorative materials. a composite resin and a compomer, using filters which have peak wave length of 430nm, 450nm, 470nm, respectively. The results were as follows: 1. All the experimental groups showed lower hardness value than the control group. 2. In DyractAP, the hardness value by wavelength showed the same changing pattern on both upper and lower surfaces. 3. In DenFil, the hardness value by wavelength showed different changing pattern on upper and lower surfaces. 4. The hardness ratio showed similar pattern to the hardness variation of lower surface. but there was no significant difference between measurement in 10 minutes and 3 days later, besides the increase of hardness value.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.217-219
• /
• 2012

In this study, the experiment was conducted in the level of mortar as one of the basic studies on pre-cast concrete which acceleration curing is not done. This study has the purpose to develop the strength of mortar into 20MPa within 6 hours in the condition of room temperature using admixtures which can accelerate C3S hydration reaction. In this experiment, W/C was fixed into 20%, PCE which can stimulate C3S was used as an accelerating admixture. From the results of this experiment, maximum content of accelerating admixture was 1%. Also, as more than 20MPa was measured through 6-hour compressive strength, it can be known that strength can be developed without steam-curing.

• Journal of the Korean Ceramic Society
• /
• v.35 no.2
• /
• pp.185-195
• /
• 1998

This experiment carried out in order to investigate the effect of the chemical activators for acceleration of hydration the system of Fly ash-Cao The paste was consisted of 80wt% Fly ash and 20wt% CaO with 1. 3. 5wt% of 4 activators(N{{{{ alpha _2 }}S{{{{ OMICRON _4 }}, CaC{{{{ {l }_{2 } }}, NaOH, Ca(N{{{{ OMICRON _3 {)}_{2 } }} and W/S ratio of 0.42 After curing for 1, 3, 7, 14, 28 days the paste hydration was characterized by the measurement of compressive strength XRD analysis SEM observation the combined water and the reaction amount of Ca(OH)2 determination. As a result of this ex-periment all of the system which involved Na2SO4 or NaOH had a god compressive strength. In the case of 7 days curing a system which added CaCl2 showed the highest compressive strength among all especially NaOH system showed a high increase in strength as a dosage of it increased. Hydration products were different according to activatores added. Only C-S-H was observed in NaOH system. As the reaction amount of Ca(OH)2 and combined water were increased the compressive strength increased. There were few differences in the comparision of strength between ignited loss 3.1% and loss 9.3% of fly ash.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.12
• /
• pp.71-75
• /
• 1972

To investigate the effects of C. E. P. A(2-chloroethyl phosphonic acid) on the ripening of tobacco leaf, the effects on the yield and quality of leaf tobacco, this experiments were carried out during the period of from 1970 to 1971 at tobacco experiment station, Sosa, Korea and 3 locations. The results are summarized as follows. 1. The higher the C. E. P. A concentration was, the more the leaf ripening was accelerated. During the period from 3 to 4 days after treatment, the differences of leaf ripening among levels were prominent. 2. Treatment with C. E. P. A only on the upper surface of the tobacco leaf, accelerated the ripening of that particular part treated, but not apparently the other parts of leaf. 3. Distinctive acceleration of leaf ripening was, obserbed in the fully develope1lower leans, however, the upper leaves were indistinctive. 4. The higher C. E. P. A concentration was, the more the effect of ripening acceleration was. But the yield was reduced over 900ppm because of the low of growth of leaves and the reduced yield was 90% at the 3, 000ppm. So the proper concentration was regarded as 900ppm. 5. In the view point of the days of C. E. P. A ripening acceleration, it was shortened one days at 100 ppm, three days at 300ppm, three days at 450ppm, four days at 900ppm, seven days at 3, 000ppm. 6. In the point of curing process, it was possible that the curing time and fuel was reduced 29% and 45% respectively in the C. E. P. A treatment than the check. 7. Therefore, if it is treated the C. E. P. A at 900ppm in the tobacco cultivation, the quality shall be increased 13.5% and the price shall be increased 12% in the 10 Are. In the point of subsidiary affect, it is possible that the C. E. P. A ripening acceleration is shortened about 7 days at 3, 00ppm and curing time is shortened about 24 hours.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.111-118
• /
• 1992

The curing acceleration of epoxy/amine system was investigated by using differential scanning calorimeter(DSC), The epoxy, diglycidylether of bisphenol A (DGEBA) was cured with methylene dianiline (MDA) with or without accelerators. Two kinds of accelerators were tested for the study ; tris(dimethylaminomethyl)phenol (DMP - 30) and 3 - (3,4 - dichlorophenyl)-1, 1-dimethylurea (DIURON). Heats of reaction and glass transition temperatures ($T_g$) of the cured epoxy system were analyzed by DSC along with the estimation of activation energy by the dynamic DSC studies. It was found that DMP - 30 is more effective accelerator than DIURON which showed faster curing and lower activation energy.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.121-127
• /
• 2012

This paper is to present the strength estimation of the cement mortar incorporating 20% of fly ash by equivalent age method. ASTM C 1074 was applied to achieve apparent activation energy($E_a$). Cement mortar was cured at the temperature of $5^{\circ}C$, $20^{\circ}C$ and $35^{\circ}C$ respectively to measure the setting time and compressive strength at designed age. According to test results, it is found that an increase in curing temperature resulted in an acceleration of setting time. $E_a$ was achieved to 34.75 KJ/mol. It was also found that by estimating strength development with Plowman and Gompertz model, good agreement between calculated value and measured one was achieved.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.133-136
• /
• 2007

This study investigates mechanical properties of the concrete using fine particle cement which is manufactured by the pulverizing process. The variable factors are 3 types of W/C such as 40, 50, and 60%, 3 types of curing temperature such as 5, 20, and $35^{\circ}C$, and 5types of the replacement of the fine particle cement such as 0, 25, 50, 75, and 100%. The unit water content, S/a and amount of the SP and AE agents to secure the slump and air content is gradually increased in accordance with amount of replacement. It can be confirmed that the delay of the setting time depending on FC content is decreased corresponding to FC content, so the effect of the acceleration to the setting time is expected. The compressive strength corresponding to FC content is proportionally increased, and the growth is confirmed about $30{\sim}40%$ at a day in 50% of FC contents. However, the increase of the strength is gradually decreased in accordance with increasing age.