• 약학회지
• /
• 제3권1호
• /
• pp.26-34
• /
• 1957

The solar evaporation method is one of the most important and popular salt manufecturing method in Korea. The rate of evaporation of sea water depends on a complex climate factors. Of these factors, the most important is solar radiation and in particular the extent to which it is absorbed in the brine. By the addition of suitable dyestuff, a further increase in absorption is obtained and can result in all the radiation entering the brine being made available as heat. "Solivap Green", one of several dyestuffs which have been suggested for accelerating solar evaporation, was tested in this experiment. The results of the experiment. 1. Increase the evaporation rate of brine up to 20-25%. 2. Elevate the temperature of brine 2-$4^{\circ}C$. higher than that of brine adding no dyestuff. 3. Optimum dyestuff concentration is 25-30 mg/L and allowable maximum concentration can not exceeded 1000 mg/$m^2$ (50 mg/L). 4. Addition of dyestuff does not cause the degradation of salt produced. 5. A conversion table which indicates the concentrations for various depths of brine was prepared for engineering purpose. 6. Absorption spectrum of the dyestuff was studies, but toxicological and structural studies for the dyestuff have not been done in this experiment.

• 전기학회논문지
• /
• 제65권4호
• /
• pp.666-672
• /
• 2016

Recently the fingerprint is widely used as one of biometrics to improve the security of financial mobile applications, because of its user convenience and high recognition rate. However, in order to apply fingerprint algorithms to finance and security applications, the recognition rate and processing speed of the fingerprint algorithms have to be improved further. In this paper, we propose the parallel fingerprint enhancement algorithm on general-purpose computing on graphics processing unit (GPGPU) using OpenCL. We discuss the analysis of the parallelism in the fingerprint algorithm as well as the exploration of optimization parameters of the parallel fingerprint algorithm to improve the performance. The experimental results showed that the execution of parallel fingerprint enhancement algorithm on GPGPUs was accelerated from 29.4 upto 69.2 times compared with the execution of the original one on the host CPUs.

• 한국자동차공학회논문집
• /
• 제1권3호
• /
• pp.1-11
• /
• 1993

An experimental study was carried out to evaluate the characteristics of transient performance of carburettered gasoline engine under rapid accelerating transient driving conditions. In order to evaluate the characteristics of transient performance quantitatively, the concept of dead time $t_d$ response delay time $t_r$ are introduced. Performance parameters such as air mass fiowrate Gat, engine speed N, manifold boost pressure Pb, and output torque T are measured simultaneously during the rapid opening of the throttle valve by the stepping motor. During the rapid opening of the throttle valve, air mass fiowrate Gat is increased immediately without delay time, but response of engine revolution N, and output torque T are delayed. Therefore hesitation, and stumble phenomena are occurred. Dead time $t_d$ and response delay time $t_r$ of engine revolution N, which is extremely delayed comparing to other performance parameters, are respectively 0.2-0.3sec., 3.0-4.6sec., and dead time rate $t_d/{\Delta}t$ and response delay time rate $t_r/{\Delta}t$ are linearly increased with the throttle valve opening rate ${\theta}$ during the acceleration from 12 degree to 20 degree at 1250rpm.

• 한국염색가공학회지
• /
• 제8권4호
• /
• pp.42-51
• /
• 1996

Alkaline hydrolysis to improve the hand of PET/acetate union fabric was studied in relation to skin saponification and retarding effect of salts on the alkaline hydrolysis of cellulose acetate fiber, accelerating effect of salts on the alkaline hydrolysis of PET fiber, and changes of total hand value(T.H.V) of PET/acetate union fabric treated with alkali/salt solution. It was found that the rate of saponification of acetate was delayed by the addition of salts such as LiCl, NaCl and CH$_{3}$COONa into NaOH solution below 10 minutes. The rate of shrinkage of acetate fabric treated with 5g/l NaOH solution at 9$0^{\circ}C$ and 60 minutes showed 20 % but it was decreased 8% by. the addition of 120g/l Concentration of inorganic salts. We could know that the rate of alkaline hydrolysis of filament yarn treated with alkali solution at 9$0^{\circ}C$ and 60 minutes was delayed about 3 % using 2,000T/M of hard twist yarn, especially acetate filament treated with alkali solution at 9$0^{\circ}C$ and 10 minutes was delayed about 10%. T.H.V. of PET/acetate union fabric was increased from 2.77 to 3.04~3.18 by the addition of salts into alkali solution.

• 한국컴퓨터정보학회논문지
• /
• 제15권4호
• /
• pp.57-63
• /
• 2010

Levenberg-Marquardt 알고리즘에서 감쇠 파라미터는 오류역전파 학습과 Gauss-Newton 학습의 스위치 역할을 하며 학습 속도에 영향을 준다. 이런 감쇠 파라미터를 고정시키는 것은 오차 함수의 진동을 유발하고 학습 속도를 감소시킨다. 따라서 본 논문은 오차 함수의 변화 과정을 참조하여 감쇠 파라미터를 가변적으로 적용하는 방법을 제안한다. 제안된 방법은 오차의 변화량이 크면 감쇠 파라미터를 크게, 오차의 변화량이 작으면 감쇠 파라미터를 작게 조정한다. 이것은 모멘텀과 유사한 역할을 하여 학습 속도를 향상시킨다. 제안된 방법의 검증을 위한 실험으로는 iris 분류 문제와 wine 분류 문제를 사용하였다. 제안된 방법은 iris 분류 문제에서는 67% 학습에서, wine 분류 문제에서는 78% 학습에서 학습 속도가 향상되었으며 기존 방법과 비교하여 오차의 진동도 적은 것을 확인할 수 있었다.

• 지질공학
• /
• 제32권1호
• /
• pp.127-142
• /
• 2022

This study explored the fluid transfer characteristics of simultaneous pneumatic blasting, plasma blasting, and vacuum suction (the PPV method), and assessed their effect. Chemical oxidation-an established soil remediation method-was compared as a control. Electrical resistivity surveys found that PPV reduced resistivity by about 1.5-2.5 times compared with the control group, indicating that it increased the diffusion of fluid between the injection and suction wells. Injection and suction tests comparing the injection flow rate, initial suction flow rate time, and suction flow rate showed that the PPV method offered an improvement over the existing method. Slug tests revealed that PPV increased the permeability coefficient by a greater amount than that by the control method. This study qualitatively and quantitatively confirmed that the PPV method clearly improves injection and suction efficiency by accelerating cracks in the ground and improving water permeability compared with the established chemical oxidation method.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4329-4337
• /
• 2022

Jet impinging device is designed for decay heat removal on horizontal fuel rods in a low temperature heating reactor. An experimental system with a fuel rod simulator is established and experiments are performed to evaluate water film covering capacity, within 0.0287-0.0444 kg/ms mass flow rate, 0-164.1 kW/m² heating flux and 13.8-91.4℃ feeding water temperature. An effective method to obtain the film coverage rate by infrared equipment is proposed. Water film flowing patterns are recoded and the film coverage rates at different circumference angles are measured. It is found the film coverage rate decreases with heating flux during single-phase convection, while increases after onset of nucleate boiling. Besides, film coverage rate is found affected by Marangoni effect and film accelerating effect, and surface wetting is significantly facilitated by bubble behavior. Based on the observed phenomenon and physical mechanism, dry-out depth and initial dry-out rate are proposed to evaluate film covering potential on a heating surface. A model to predict film coverage rate is proposed based on the data. The findings would have reliable guide and important implications for further evaluation and design of decay heat removal system of new reactors, and could be helpful for passive containment cooling research.

• 분석과학
• /
• 제14권3호
• /
• pp.203-211
• /
• 2001

우라늄산화물중 Cs의 전자탐침 미세분석시 우라늄에 의한 방해와 몇 가지 Cs 화합물의 Cs $L_{\alpha}$ X-선 세기 안정도를 측정하였다. Cs 화합물 중 CsI의 Cs $L_{\alpha}$ X-선 세기가 가속전압과 결정의 종류에 관계없이 가장 높았다. 빔전류량 100 nA 사용시 Cs $L_{\alpha}$ X-선 세기는 측정시간이 경과함에 따라 감소하였으며, X-선 세기의 감소율은 가속전압과 빔전류량에 비례하였으나 빔직경에 반비례하였다. $UO_2$ 시편에 함유된 Cs의 전자탐침미세분석시 LiF결정의 Cs $L_{\alpha}$ X-선 파장을 사용하면 우라늄에 의한 방해를 제거 할 수 있었다.

• 방송공학회논문지
• /
• 제19권5호
• /
• pp.699-712
• /
• 2014

본 논문은 High Efficiency Video Coding (HEVC) GPU 기반 정수화소(integer-pel) 움직임 추정(Motion Estimation)을 고속화하기 위한 적응적인 탐색영역 결정 방법을 제안한다. 적응적인 탐색영역은 Motion Vector Difference (MVD)를 이용하여 결정한다. 먼저, 입력 영상의 MVD를 분석하여 입력 영상을 두 모델로 분류한다. 이후 분류된 각 모델의 MVD 특성에 따라 적응적인 탐색영역을 결정한다. 제안하는 알고리즘을 GPU 기반 정수화소 움직임 추정에 적용하기 위해 움직임 추정의 시작점은 이전 프레임의 Motion Vector (MV)로 결정한다. 위 과정은 CPU에서 이뤄지며, CPU는 움직임 추정의 시작점과 적응적인 탐색영역을 GPU에 전송한다. 이후 GPU는 정수화소 움직임 추정을 병렬로 수행한다. 제안하는 알고리즘은 참조 모델 대비 1.1%의 BD-rate 상승과 전체 부호화 시간의 37.9% 감소 및 951.2배 빠른 정수화소 움직임 추정 수행 시간을 얻는다. 또한, 적응적인 탐색영역이 적용되지 않은 단순 병렬화 알고리즘 대비 57.5%의 정수화소 움직임 추정 시간 감소와 0.6% BD-rate 상승을 얻는다.

• 한국재료학회지
• /
• 제11권2호
• /
• pp.94-103
• /
• 2001

졸-겔공정을 이용하여 SiO$_2$ 및 TEOS에 유기 고분자로서 PDMS가 도입된 PDMS/SiO$_2$ xerogel을 제조하고 촉매로서 HCI과 NH$_4$OH를 이용한 2 step acid/base catalyzed공정에 의해 SiO$_2$ 및 PDMS/SiO$_2$ xerogel의 기공 크기 및 분포를 제어하였다. 촉매로서 HCl이 첨가된 SiO$_2$ 및 PDMS/SiO$_2$ xerogel에서 PH는 2.3~2.5, gel화 시간 12~13일, xerogel의 모양은 Pellet형태를 나타내나 HCl/NH$_4$OH 몰비가 증가하면 pH 및 gel화 시간은 급격히 감소하고 xerogel의 모양도 pellet형과 column형으로 뚜렷하게 구분된다. 이는 반응의 최종용액이 산성이면 가수분해속도가 축합속도보다 빠르게 진행되어 9el화에 오랜 시간이 소요되어 pellet형의 Xerogel이 되나 약산성에서는 축합속도가 가수분해속도보다 빠르게 되어 gel화 시간은 빨라지고 column형의 xerogel이 되기 때문이다 SiO$_2$ 및 PDMS/SiO$_2$, xerogel의 표면적 및 평균기공크기는 HCl/NH$_4$OH 몰비가 증가함에 따라 각각 400$\rightarrow$600($\m^2$/g)과 15$\rightarrow$28$\AA$ 으로 변화하고 단일 기공크기분포를 갖는다. 이는 초기에 HCl에 의해 가수분해된 종이 NH$_4$OH에 의해 축합속도가 촉진되어 silica의 골격구조가 낮은 온도에서 규칙적으로 형성되고 열처리에 의해 균일한 기공으로 되었기 때문이다.