• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.491-498
• /
• 1998

Based on FDTD(Finite-Difference Time-Domain) method the human head absorbed power radiated from a 1.8 GHz portable phone is computed. For this computation the 7 layered media for the human head modeling and the monopole antenna attached to metallic box for the portable phone are used. To reflect the real circumstances typical sizes of human heads and portable phones are considered in the calculation. The length of monopole antenna is 4.5 cm. Under the predetermined model the distribution of SAR over the human head are calculated, and from which the place of maximum SAR is near the head skin surface, not deep places far into the head. The computation shows the maximum SAR to be 1.4 mWg somewhat less than the internationally adopted value of 1.6 mW/g.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.3
• /
• pp.371-375
• /
• 2013

A new model about output power prediction of PV module with various tilted angles and cell to cell distances has been proposed in this paper. Light intensity arrived on a solar cell could be changed by characteristics of PV module materials. Refractive indices, thickness and absorption coefficients of glass, EVA, solar cell and Backsheet are used to predict output. Also, the incident angle of light is changed 0 to 90[$^{\circ}$] and cell to cell distances are 5, 10 15[mm]. Two types of light incident on a solar cell are considered which are direct to a solar cell and reflected from Backsheet. The intensity of the incident light directly into the solar cell is reduced through glass and EVA about 17.5[%] in theoretical way. It has an error of 2.26[%] compared with experimental result. The results for compare theoretical with experimental data is validated within the error of 6.3[%]. This paper would be a research material to predict output power when the PV module is installed outdoor or a building.

• Korean Chemical Engineering Research
• /
• v.45 no.1
• /
• pp.81-86
• /
• 2007

Hollow fiber membrane G-L contactors are widely used to remove $SO_2$ emitted from industrial facilities. In this work, the mathematical modeling and computer simulation for hollow membrane G-L contactors is carried out to analyze $SO_2$ absorption behavior in hollow fiber membranes. The model is solved with the finite element method using a commercial software. Investigated is the dependency of $SO_2$ removal efficiency and mass transfer characteristics on gas velocities, membrane mass transfer coefficients and physical properties of contactors. The membrane mass transfer coefficients are estimated by fitting the experimental data with the simulated $SO_2$ removal efficiencies. In addition, a design methodology of membrane contactors is suggested.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2C
• /
• pp.119-125
• /
• 2011

Start This paper analyzes the propagation characteristics of acoustic signals in indoor environments, which is applicable to indoor positioning system. Indoor stereo sound system is generally valid within $25m^2$. So it is not possible to apply prevalent sound propagation characteristic to indoor positioning system because the prevalent acoustic signals propagation characteristic is defined under free space condition. Therefore, in this paper, we present the propagation characteristics of acoustic signals in indoor environments considering the free space propagation characteristic as well as room characteristic such as humidity, temperature, absorption of atmosphere and so on. To verify the designed propagation model of indoor acoustic signals, this paper presents the propagation characteristics of decreasing sinusoidal signals whose frequencies ate from 1kHz to 20kHz in anechoic room. In addition, this paper also presents the propagation characteristics of decreasing sinusoidal signals which have multiple frequencies.

• Journal of Environmental Health Sciences
• /
• v.40 no.5
• /
• pp.407-412
• /
• 2014

Objectives: The internal dose of ethyl parabens is important in order to evaluate the risk of this chemical. However, there are little PK model data for parabens to apply this. This experiment attempted PK modeling to ascertain PK values. Methods: Twenty mg/kg ethyl paraben was administered orally to Sprague-Dawley rats at the same point in time. The rats were sacrificed at times 0, 15, 30 and minutes, and 1, 2, 4, 8, 12, 24 hours after oral gavage. Blood and urine were collected and pretreated for analysis. Accuracy, precision and LOD (limit of detection) were calculated for this analysis. Ethyl paraben, detected by HPLC-MS, was applied to PK modeling using Berkeley Madonna. Results: This study showed 100.1-103.7% accuracy, 1.4-3.7% precision and a 1.0 ng/mL limit of detection. Orally administered ethyl paraben reached maximum concentration after 30 minutes of dosing in serum and urine of rats. The concentrations were 2,354 ng/mL in serum and 386,000 ng/mL in urine samples. These peak concentrations were excreted after one hour of intubation over 12 hours. For the pharmacokinetic parameters of ethyl paraben revealed using Berkeley Madonna, the absorption rate was 5.539/hour, the excretion rate was 0.048/hour, the half-life was 14.441 hours and AUC was 481,186 ng hour/mL. Conclusion: Orally administered ethyl paraben was absorbed rapidly in rats and excreted in urine. This chemical, ethyl paraben, accumulated in the body but was excreted over 12 hours after dosing.

• Korean Journal of Agricultural Science
• /
• v.39 no.4
• /
• pp.603-612
• /
• 2012

In this research, the feasibility of non-destructive measurement technique of pungency measurement was investigated for the red-pepper powders produced in different domestic areas in South Korea. The near-infrared absorption spectra in the range of 1100 nm~2300 nm was used to measure capsaicinoids content in red-pepper powders by using a NIR spectroscopy equipped with Acousto-optic tunable filters (AOTF). Fourth three different red-pepper powders from 14 different locations were collected and separated in three different particle size (below 0.425 mm, 0.425~0.71 mm, 0.71~1.4 mm) for the spectral measurements. The partial least square regression (PLSR) models to predict the capsaicinoids content depends on particle size were developed with the measured spectra. The determinant coefficients and standard errors of the developed models for the red-pepper powders of below 0.425 mm, 0.425~0.71 mm, and 0.71~1.4 mm were in the range of 0.859~0.887 and 12.90~12.99 mg/100 g, respectively. The PLS model with the pretreatment of Standard Normal Variate (SNV) for the red-pepper powders below 1.4 mm particle size showed the best performance with the determinant coefficient of 0.844 and the standard error of 14.63 mg/100 g.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.56-60
• /
• 2017

In hypersonic aircraft, increase of aerodynamic heat and engine heat leads heat loads in airframe. It could lead structural change of aircraft's component and malfunctioning. Endothermic fuels are liquid hydrocarbon fuels which are able to absorb the heat load by undergoing endothermic reactions. In this study, exo-tetrahydrodicyclopentadiene was selected as a model endothermic fuel and experiments were investigated in endothermic fuel cooling system with zeolite catalyst. Three shapes of catalysts have been manufactured and endothermic characteristics were recovered. Bineded catalyst showed higher heat absorption and conversion than other two zeolite catalysts. In product distribution, binded catalyst showed higher aromatics composition.

• Steel and Composite Structures
• /
• v.37 no.2
• /
• pp.175-191
• /
• 2020

In this article, for the first time, the seismic behavior of elliptic-braced moment resisting frame (ELBRF) is assessed through a laboratory program and numerical analyses of FEM specifically focused on the development of global- and local-type failure mechanisms. The ELBRF as a new lateral braced system, when installed in the middle bay of the frames in the facade of a building, not only causes no problem to the opening space of the facade, but also improves the structural behavior. Quantitative and qualitative investigations were pursued to find out how elliptic braces would affect the failure mechanism of ELBRF structures exposed to seismic action as a nonlinear process. To this aim, an experimental test of a ½ scale single-story single-bay ELBRF specimen under cyclic quasi-static loading was run and the results were compared with those for X-bracing, knee-bracing, K-bracing, and diamond-bracing systems in a story base model. Nonlinear FEM analyses were carried out to evaluate failure mechanism, yield order of components, distribution of plasticity, degradation of structural nonlinear stiffness, distribution of internal forces, and energy dissipation capacity. The test results indicated that the yield of elliptic braces would delay the failure mode of adjacent elliptic columns and thus, help tolerate a significant nonlinear deformation to the point of ultimate failure. Symmetrical behavior, high energy absorption, appropriate stiffness, and high ductility in comparison with the conventional systems are some of the advantages of the proposed system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.45-54
• /
• 2004

Microwave characteristics of ridge type CPW traveling-wave(TW) electroabsorption modulator and photodetector are affected by the thickness of intrinsic layer, width of guiding layer, and the separation of signal and ground electrodes. These factors are determined effective index of microwave and characteristic impedance due to changing of capacitance(C) and inductance(L) of device. However, conventional equivalent circuit of TW-structure is approximated to microstrip and CPW transmission line by distribution of electric and magnetic fields, respectively. In this paper, we analyzed microwave characteristics of TW-structure and found more accurate value of C and L by using finite difference time domain (FDTD) method. These values are adopted circuit element of equivalent circuit. Microwave characteristics obtained by the FDTD and equivalent circuit model show good agreement.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.6
• /
• pp.541-548
• /
• 2009

In this study, Charpy impact test and numerical studies were performed to examine the effects of failure behavior and energy absorption on the notch position. For this purpose, carbon steel plate(SA-516 Gr. 70) with thickness of 25mm usually used for pressure vessel was welded by SMAW(Shielded Metal-Arc Welding)method and specimens were fabricated from the welded plate. The Charpy impact tests were then performed with specimens having different notch positions varying within HAZ. A series of three-dimensional FE analysis which simulates the Charpy test and crack propagation are carried out as well. We divided HAZ into two, three and four regions to apply mechanical properties of HAZ to FE-analys. Results reveal that the absorbed energies during impact test depend significantly on the notch position. To obtain the results of reliability, HAZ should be divided into at least three regions.