• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.92-99
• /
• 2016

Polyurethane resin used to leather coat was synthesized by the addition reaction of PPG and PTMG with different mole ratios. Physical characteristics of the synthesized polyurethane resin were measured by the SEM, FT-IR and the UTM. Increasing mole ratio of PTMG having four methylene groups caused the increase of abrasion resistance and tensile strength. The elongation was decreased. As we measured the solvent(toluene) resistance of poly urethane resin, it was found the there were no effect of PTMG mole ratios on the phyhsical properties of the resin. The viscosity was increased by ratio of PTMG mole ratio.

• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.65-69
• /
• 2010

This paper presented an experimental study of slip resistance characteristics of shoes and floor surface contact with special focus on the effect of surface roughness, outsole material and mechanical abrasion. The factors that affected the results of slip resistances were investigated for four kinds of rubbers and five kinds of floor samples using the VIT(English XL) tribometer. The slip resistance was observed to increase gradually with increasing roughness for five kinds of floor roughness. In the higher surface roughness (larger than $11.5{\mu}m$), the slip resistance increased more rapidly and exceeded safety criteria at $22.60{\mu}m$. The slip resistance was observed to decrease with increasing hardness of outsole, except for butylenes rubber, which seemed to show the material property. The slip resistance decreased with number of trials. In the first several times(5 or 6 trial), the slip resistance decreased more rapidly, whereafter it approached gradually constant value. The slip resistance of surfaces has generally been shown to increase with floor surface roughness and to decrease with hardness of outsole and number of trials under the wet condition.

• Journal of Korean Society of Rural Planning
• /
• v.11 no.3 s.28
• /
• pp.53-57
• /
• 2005

Up to recently building are constructed focusing on the convenience of residential condition. However, environmental-friendly materials is required for construction as people are spending more time inside buildings and causes of many problems like sick-building syndrome are known due to the noxious gases and polluted air originated from construction materials. Although loess(hwangtoh) is an environmental-friendly material, it has limitations in compressive strength far a construction material. The purpose of this study is to suggest the optimal ratio of loess(hwangtoh) mortar by tests of compressive strength comparing with standard strength of floor finishing mortar and evaluate the usability of loess(hwangtoh) mortar for floor finishing material through an impact test, a cracking test and a abrasion test. Based on the results of this study, 86% of loess(hwangtoh) and 14% of inorganic binder is suggested for the optimal mixture ratio of loess(hwangtoh) mortar. Moreover, the characteristics of loess(hwangtoh) is suitable for floor finishing material in impact, crack, abrasion.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.2071-2072
• /
• 2011

Withstand voltage characteristics of the nanocomposites, as a material with excellent abrasion resistance and water resistance, low shrinkage upon curing with moisture even in very good adhesion, workability is not lost. In this study, the fusion of nanoparticles and the high functionality epoxy nano-composite material produces the electricity. Degeneration of the unit based on this power structure and breakdown characteristics, efficiency and cross-measurement system as closely related organisms that can be applied to the power plant electrical efficiency of the nano-composite material is designed to develop skills.

• Tribology and Lubricants
• /
• v.7 no.2
• /
• pp.61-66
• /
• 1991

The frictional and wear characteristics of non-asbestos friction materials made of four different fibers (carbon, aramid, ceramic and glass) have been investigated at elevated temperature using High Frequency Friction Tester. On the basis of the experimental results, friction and wear phenomena of four different non-asbestos fibers were caused by lattice layer film of carbon, polymeric transfer film of aramid, abrasion of ceramic and adhesion of glass fiber under each contact junction. The surface analysis of the worn specimens and counter parts after tests were observed using Scanning Electron Microscope and Optical Microscope.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.324-331
• /
• 2000

Wear characteristics of Plastic and Nylon pinions against steel gear were studied to gain a better understanding of their tribological behaviors. Wear tests were conducted with power circulating gear test rig under dry contact conditions. Specific wear rates were measured as a function of applied load and the number of revolution. The worn teeth surfaces were examined with a profile projector and a camera. Nylon pinion showed lower specific wear rates than acetal pinion, but suffered teeth breakage under high load per unit tooth width. The dominant wear mechanisms found were adhesion and abrasion.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.1
• /
• pp.118-128
• /
• 2001

This study was performed to evaluate the toothbrush abrasion characteristics of seven commercially available light-cured cervical restorative materials one resin-modified glass-ionomer material(Fuji II LC) three polyacid-modified composites(Compoglass, Dyract, F2000), and three light-cured composites(Heliomolar, Palpique Estelite, UniFil F). All samples were stored in distilled water at $37^{\circ}C$ for 10 days. 2.0N of weight was loaded during the test and the abraded surfaces were examined with profilometer and SEM after 100,000 cycles. The results obtained were summarized as follows; 1. The highest hardness value of 79.7 was observed in the FT group and the lowest value of 20.0 was observed in the HM group. Results of Tukey test showed that an overall significant difference was indicated except the CG and DR groups(p<0.05). 2. The highest surface roughness was observed in the FL group and the lowest was observed in the UF group. Results of Tukey test showed the significant difference between the FL or FT and UF groups(p<0.05). 3. Statistically higher abrasion and surface roughness were observed for the dentifrice of paste type, Perio A+, than for that of gel paste type, Tom & Jerry. 4. The surface roughness values increased on the abraded surfaces because of the protrusion of filler particles due to selective removal of matrix resin.

• Journal of Periodontal and Implant Science
• /
• v.29 no.1
• /
• pp.209-231
• /
• 1999

Even though titanium(Ti) and its alloys are the most used dental implant materials, there are some problems that Ti wears easily and interferes normal osteogenesis due to the metal ions. Ti coated with bioactive ceramics such as hydroxyapatite has also such problems as the exfoliation or resorption of the coated layer, Recent studies on implant materials have been proceeding to improve physical properties of the implant substrate and biocompatibility of the implant surfaces. The purpose of the present study was to examine the physical property and bone tissue compatibility of bioinert nitrides ion plated Ti, Button type specimens(14mm in diameter, 2.32rrun in height) for the abrasion test and cytotoxicity test and thread type implants(3.75mm in diameter, 6mm in length) for the animal experiments were made from Ti(grade 2) and 316LVM stainless steel. Ti specimens were ion plated with TiN, ZrN by the low temperature arc vapor deposition, and the depth profile of the TiN/Ti, ZrN/Ti ion plated surface was examined by Auger Electron Spectroscopy. Three kind of button type specimens .of TiN/Ti, ZrN/Ti and Ti were used for abrasion test, and HEPAlClC7 cells and CCD cells were cultivated for 4 days with the specimens for cytotoxicity test. Thread type implants of TiN/Ti, ZrN/Ti, Ti, 316LVM were implanted on the femur of 6 adult dogs weighing 10kg-13kg. Two dogs were sacrified for histological examination after 45 days and 90 days, and four dogs were sacrified for the removal torque test of the implant') after 90 days. The removal torque force was measured by Autograph (Shimadzu Co., AGS-1000D series, Japan). Abrasion resistance of TiN/Ti was the highest, and that of ZrN/Ti and Ti were followed. The bioinert nitride ion plated Ti had much better abrasion resistance, compared with Ti, In the cytotoxicity test, the number of both cells were increased in all specimens, and there were no significant difference in cytotoxic reaction among all groups (p>0.1), In histological examination, 316LVM showed the soft tissue engagement in interface between the implant and bone, but the other materials after 45 days noted immature new bone formation in the medullary portion along the implant surface, and those after 90 days showed implant support by new bone formation in both the cortical and the medullary portion, The removal torque force of Tilv/Ti showed significantly higher than that of Ti(p(O,05). The difference in removal torque force between TiN/Ti and ZrN/Ti was not significant(p>0.05), and that of 316LVM was lowest among all groups(p<0.05). These results suggest that bioinert nitrides ion plated Ti can resolve the existing problems of Ti and bioactive ceramics, and it may be clinically applicable to human.

• Korean Journal of Plant Resources
• /
• v.27 no.1
• /
• pp.72-79
• /
• 2014

This study was investigated the changes in quality of peeled chestnut according to peeling method, including abrasion and knife, and 3 kinds of storage temperatures. The weight loss rate of peeled chestnut during storage period was observed in all treatment groups, peeling methods showed no difference of the loss. However, the moisture content of peeled chestnut during storage in all treatments showed a tendency to decrease. Moisture content of the abrasion peeled chestnut in all treatments was higher than that of the knife peeled chestnut. In the case of a, b, and ${\Delta}E$ value of peeled chestnut chromaticity increased during storage in all treatments, whereas, L values decreased during storage. But, browning of abrasion peeled chestnut was higher than that of the knife peeled chestnut. The hardness of the abrasion and knife peeled chestnuts were the highest in $-1^{\circ}C$ storage, soluble solid content was decreased with storage time in all treatments, but showed a tendency to increase within 24 days. Palatability and texture of peeled chestnuts decreased in all treatments during storage period, 15 days after storage decreased rapidly. Thus, results showed that peeled chestnuts stored at $4^{\circ}C$ and $2^{\circ}C$ were rapidly decreased in the quality after 15 days, whereas, peeled chestnuts stored at $-1^{\circ}C$ slowly decrease in the fruit quality. It can be recommended that chestnut in vacuum film is good to maintain at $-1^{\circ}C$ storage for 15 days. Also, if we can reduce the browning of abrasion peeled chestnut, we will produce peeled chestnut of high quality.

• Elastomers and Composites
• /
• v.41 no.2
• /
• pp.79-87
• /
• 2006

This study are conducted for the purpose of developing rubber material with noise and crack resistance. Cure characteristics, physical properties, thermal resistance, fuel resistance, abrasion resistance, crack resistance and noise resistance of NBR compounds with the various amounts of oleamide and aramid chip were investigated. From the measurements of cure characteristics and Mooney viscosities, cure characteristics of uncured rubber showed that a torque was decreased as the amount of oleamide increased. Hardness, modulus and elongation of rubber specimens tended to be reduced gradually, however, tensile strength remained unchanged as the amount of the oleamide increased. As a testing results of heat resistance for 70 hours at $120^{\circ}C$ and oil resistance far 70 hours at $40^{\circ}C$, tensile strength and elongation were all reduced. From the TGA/DSC analysis, there was no such a change observed in thermal characteristics of rubber materials. As a result of testing basic physical properties, abrasion resistance, noise resistance and crack resistance, the optimum ratio of oleamide to NBR was found to be 3 phr, while that of aramid to NBR 227001 was 1 phr.