• Journal of Nutrition and Health
• /
• v.25 no.7
• /
• pp.668-683
• /
• 1992

To evaluate the current practices of the tube feeding and the status of tube feeding patient 76 adult in-patients at 6 hospitals located in Seoul and Chung-buk province were examined through reviewing patient charts observing patients and interviewing patients nurses dietitians patients' family or care-givers. The results were as follows : 1) An average age of the patients was 54.5 years with 41% over 60 years old. Patients with decreased mental status dysphagia esophageal obstruction and respiratory problem were fed by tubes. 2) The range of duration of tube feeding is between 4 days and 6 years. Most patients were received formula through nasogastric tube(89.5%) while 7.9% of gastrostomy and 2.6% of jejunostomy. Administration method for formula were bolus feeding regardless of the route of formula delivery. 3) Mean total calories received for men were 1590 kcal and 1450 kcal for female. Mean volume per meal was 282m, l and mean frequency of feeding was 5.68 while mean feeding interval 3$\frac{1}{4}$ hours and mean rate of infusion 68.4ml/min. All patients received hospital-blenderi-zed formula as the major source of nutrition. Home-blenderized formula and commercial formula as a supplement were used 35%, 13.2% respectively. 4) Thirty-eight percent of patients was hypoalbuminemia and 61% was at the moderate level of deficiency in hemoglobin. 5) Complications associated with tube feeding were diarrhea (22.4%) constipation(21.1%) vomiting(11.8%) and so on. 6) Serum albumin levels of patients who have complications associated with tube feeding were significantly lower than those of patients without complications In planning a tube feeding regimen the type of a formula must be integrated with both a delivery system and a protocol for administering the tube feeding. the multidisciplinary effort required to deliver enteral therapy is essential to improve current practices used at hospitals.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1426-1430
• /
• 2009

AC AT feeding method consists return circuits of electric train inserting in parallel between trolly line and feeding line and connecting neutral line to rail and FPW. Due to increasing electric load at feeding system, collecting voltage of train and end voltage are going down. So to increase voltage between trolly line and rail, the usefulness of new autotransformer are considered which variation of short impedance and change of line voltage is simulated with modified winding ratio of autotransformer from 1:1 to variable tab.

• Asian-Australasian Journal of Animal Sciences
• /
• v.23 no.10
• /
• pp.1354-1363
• /
• 2010

This study compared the effect of four different feeding methods for gestating gilts on reproductive performance and growth of their progeny. A total of 40 F1 primiparous sows (Yorkshire${\times}$Landrace) were allotted to four treatments in a completely randomized design (CRD). For treatments, gestating period of sows was divided into three trimesters (0-35 d, 36-90 d and 91-110 d) and different amounts of feed were provided to each treatment group by Flat, Down-Up-Down (DUD), Up-Down-Up (UDU) and Down-Up-Up (DUU) feeding methods. The experimental diet was formulated to meet or exceed the standards of NRC (1998). Body weight gain of gestating gilts from d 0 to 110 was affected by feeding method (p<0.05). When gilts were fed constant feed ration (Flat feeding), less body weight loss was observed during lactation (-0.9 kg, p<0.05) and desirable backfat thickness (average 19.5 mm) was acquired at 110 days of gestation. Feed intake of lactating sows tended to be greater (4.22, 3.60, 3.97 and 4.13 kg/d, p>0.05) as sows in Flat feeding treatment had lower backfat thickness during gestation compared with other treatments (p<0.05). When gestating gilts were fed higher amount of feed during mid-trimester, the number of stillborn (1.4 piglet per litter, p<0.05) and mummies (0.8 piglet per litter, p = 0.25) were increased compared to other treatments. Feeding methods for gestating gilts had no effect on litter weight and gain of litter weight during the nursing period. Flat feeding method resulted in decreased plasma glucose concentration at 7 d postpartum (p<0.05), and increased LH concentration at 21 d postpartum (p<0.01) compared to other treatments. These results suggested that higher feed intake of gestating gilts resulted in detrimental effects on body condition and reproductive performance of sows. When gestating gilts consumed constant feed during gestation (2 kg/d), better reproductive performance and less body weight loss in lactation were observed because sows consumed more feed during the whole lactation period. Consequently, Flat feeding will be a desirable feeding strategy for gestating gilts to maximize reproductive performance, and better body condition of sows without any negative influence on the growth of their progeny.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.279-282
• /
• 2006

Upon a turbopump's running, cavitation may occur at the inlet of the LOx pump by pressure drop and heat transfer along the LOx feeding line. Since the cavitation can cause serious damage to the pump or to stop running, the absence of the cavitation at the inlet of a turbopump should be confirmed before the using the turbopump. In the present study, the calculation of the volume fraction of LOx gas phase at the inlet of the pump are performed with different temperatures of LOx in the tank, pressure drops and heat transfers along the feeding line. This calculation method can be applied to define the limits of thermal and hydraulic characteristics during the design of a LOx feeding system.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.27-33
• /
• 2005

Constant load model is generally used for an electric train to perform the static analysis of AT feeding systems. In this model, the train will be considered as a constant load model when it drives or as a constant source model when it applies regenerative brake. However there must be some voltage constraints on the catenary in actual operations. These constraints are established for the reason of protecting the feeding facilities from excessive rise of regenerative braking voltage or guaranteeing the minimum traction power of train. In normal operating situation, the pantagraph voltage of the train should be maintained within these limits. Keeping these facts in minds, we suggest new methods of analyzing AT feeding systems using the constant power models with the conditions of voltage constraints. The simulation results from a sample system using the proposed method illustrate both the states of system variables and the supply-demand relation of power among the trains and the systems very clearly, so it is believed that the proposed method yields more accurate results than conventional methods do. The proposed methods are believed to contribute to the assessment of TCR-TSC for compensating reactive powers too.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1322-1327
• /
• 2004

There are some previous studies that utilize constant impedance models or constant current models for electric trains to perform the static analysis of AT feeding systems. These mentioned models have some merits of linear systems but yield erroneous results because of the innate restraints of the models since linear models cannot represent the features of constant power in inverter-driven trains. From these reasons, it is suitable that the train be considered as a constant load model when it drives or as a constant source model when it applies regenerative brake. However, excessive rise of regenerative voltage during the braking may damage the vehicle itself and the feeding systems so the voltage must be restricted below a certain value. Keeping these facts in minds, we suggest new methods of analyzing AT feeding systems using the constant power models with the conditions of voltage constraints. The simulation results from a sample system using the proposed method illustrate both the states of system variables and the supply-demand relation of power among the trains and the systems very clearly, so it is believed that the proposed method yields more accurate results than conventional methods do.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.3
• /
• pp.599-604
• /
• 2017

Nowadays reactance method is being used as a technique for fault location in parallel feeding AC traction power system. However, implementation of this method requires a large number of field tests(ground fault) which is a huge burden on the operators. This paper presents a new estimation technique using quadratic interpolation to reduce number of times for field test and improves the accuracy of fault location. To verify a new technique, we solve AT feeding circuit and model it using PSCAD/EMTDC. Finally this paper conducts a comparative analysis of usefulness between a new technique and real field data.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.1
• /
• pp.85-92
• /
• 2011

Main characteristic in railroad is the guided movement of the wheel by the track through a metal-to-metal contact, conferring to the rail vehicle a single degree of freedom. There are defects such as head check, shelling, corrugation, squats etc in surface of the rail by interface between the wheel and rail. These defects bring about reducing the life-cycle of rails and track components and increasing noises. In case of bad conditions, it is possible to happen to full-scale accident such as derailment. Recently, the track capacity has been increased for increasing speed and operation efficiency. So, maintenance and indirect cost have been increased. Currently, a coating method of rail construction is proposed by using the ceramics in Korea. Rails are used as the earth in electrical railroad systems. Currently traction return current is flowed through wheels of trains. In case of rails coated, problems are caused in the contact power between wheel and coating material of spray. In this paper, electric model is presented in the AT feeding method. In case of rails coated, electric model is presented. Also, standard resistance of the ceramic is demonstrated by contact power between wheel and coating material of spray.

• Asian-Australasian Journal of Animal Sciences
• /
• v.10 no.6
• /
• pp.671-678
• /
• 1997

The objective was to evaluate method of feeding (free access or intubation), method of slaughter (carbon dioxide gas or barbiturate) and digesta flushing medium (distilled water or physiological saline), in the development of an ileal amino acid digestibility assay for 4 week-old broiler chickens. Three diets were used (commercial (C), semi-synthetic meat-and bone meal (MBM) or wheat (W)). For the coarser C and W diets but not for the MBM diet, feeding method had a significant effect on concentrations of chromium (Cr), nitrogen (N), acid detergent fibre (ADF) and neutral detergent fibre (NDF) in the crop contents at a set time after a meal. There appeared to be a selection of food particles under free-access feeding. For birds receiving the wheat diet there was an effect (p < 0.05) of sampling time after feeding on the concentrations of Cr, N, ADF and NDF/Cr in the crop contents. Flushing ileal digesta with distilled water or saline led to similar apparent ileal N digestibility coefficients. Birds given the MBM diet, and killed by inhalation of $CO_2$, had significantly (p < 0.05) lower apparent ileal N digestibility coefficients (73 versus 80%) than those killed by barbiturate overdose.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.5
• /
• pp.698-704
• /
• 2010

The machine vision system has been widely applied at automatic inspection field of the industries. Especially, the machine vision system shows good performance at difficult inspection field by contact method. In this paper, the automatic system of a slant method to inspect screw/bolt shape using machine vision is developed. The inspection system uses pattern matching method that search similar degree of the lucidity, the average lucidity, length and angle of inspection set up area using a circular scan and a line scan method. Also the feeding method for inspection product is the slant method, and feed rate is controlled by the ramp angle adjustment. This inspection system is composed of a feeding device, a transfer device, vision systems, a lighting device and computer, and is composed the sorting discharge system of the inferior product. The performance test carried out the feeding speed, the shape correct degree and the sorting discharge speed according to the type of screw/bolt. This sorting inspection system showed a satisfied test results in whole inspection items. Presently, this sorting inspection system is being used in the manufacturing process of screw/bolt usefully.