• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.107-107
• /
• 2016

TiCrAlSiN films were developed in order to improve the high-temperature oxidation resistance, corrosion resistance, and mechanical properties of conventional TiN films that are widely used as hard films to protect and increase the lifetime and performance of cutting tools or die molds. In this study, a nano-multilayered TiAlCrSiN film was deposited by cathodic arc plasma deposition. It displayed relatively good oxidation resistance at $700-900^{\circ}C$, owing to the formation protective oxides of $Al_2O_3$, $Cr_2O_3$, and $SiO_2$, and semiprotective $TiO_2$. At $1000^{\circ}C$, the increased temperature led to the formation of the imperfect oxide scale that consisted primarily of the outer ($TiO_2$,$Al_2O_3$)-mixed scale and inner ($TiO_2$, $Al_2O_3$, $Cr_2O_3$)-mixed scale.

• Journal of Powder Materials
• /
• v.2 no.1
• /
• pp.36-43
• /
• 1995

Rapidly solidified and mechanically alloyed Al-Ti base alloys were prepared by gas atomization and attritor milling separately. The gas atomized and the mechanically alloyed powders were consolidated after preheating at $450^{\circ}C$, and then heat treated isochronally for 1 hour to observe the microstructures and to investigate the mechanical properties. Stable phases of precipitates in the Al-Ti-Si and the Al-Ti-Zr alloys were identified as DO22-$(Al,Si)_3Ti$ and $Do_{23}-Al_3(Ti, Zr)$ each. Among the alloys, the mechanically alloyed Al-l0Ti-2Si alloy showed superior thermal stability and mechanical properties at elevated temperature. The additions of third elements, such as Si and Zr, to Al-Ti alloys seemed to improve the mechnical properties remarkably by stabilizing the microstructure and the precipitate phases in the consolidated alloys.

• Journal of Korea Foundry Society
• /
• v.11 no.6
• /
• pp.482-490
• /
• 1991

This study presents the wear characteristics of Ti alloys (Pure Ti, Ti-6Al-4V, Ti-5Al-2.5Sn) fabricated by centrifugal precision casting in an Ohara dental titanium casting machine. It was found that the hardness of the surface region is higher than that of the interior region. It is considered that the oxygen adsorption in the surface region during casting, leads to the interstitial solid solution hardening. Wear resistance incerases in the order of pure Ti, Ti-6Al-4V, Ti-5Al-2.5Sn alloys. The interior hardness value increases in the same order. The specific wear rate increases with applied load and increases monotonously with sliding speed. The Fe transfer from the counterpart material was observed on the worn surface of the Ti-5Al-2.5Sn alloy. Oxidative wear occurs at low sliding speeds and mechanical fracture wear occurs at high sliding speeds.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.422-426
• /
• 2006

[ $Sr_xCa_{(1-x)}TiO_3$ ] red phosphors doped with Pr(0.13 mol%) and Al(0.23 mol%) were synthesized by solid state reaction method. Change of crystal structure occurred in $Sr_xCa_{(1-x)}TiO_3:Pr,Al$ phosphors with increasing value of x. Green and red luminescence were observed from $SrTiO_3:Pr,Al$ phosphors at low temperature. However, only red luminescence in the case of $CaTiO_3:Pr,Al$ phosphors was measured at low temperature. The main cause of green luminescence was explained by the bandgap reduction.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.180-182
• /
• 2004

Polycrystalline $BaTiO_3/SrTiO_3$ powder was prepared by sol-gel process and the multilayered thick films were prepared on the $Al_2O_3$ substrates by screen printing method. The films were sintered at $1400^{\circ}C$ for 2 hours in the air. The structural and dielectric properties were investigated, The X-ray diffraction (XRD) patterns indicate that the BST phase and porocity were formed in the interface of $BaTiO_3/SrTiO_3$ multilayered thick films. The dielectric constant and the dielectric loss of the BT/ST/BT/ST multilayered thick films were about 247 and 0.84% at 1MHz.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.43-48
• /
• 2006

The oxidation behavior and Biocompatibility of pure Ti and Ti-8Ta-3Nb alloy were studied in dry air atmosphere. The specimens showed that Ti-8Ta-3Nb alloy had higher oxidation resistance than pure Ti at $650^{\circ}C$. Cytotoxicity test also revealed that moderate oxidation treatment lower cell toxicity and Ti-8Ta-3Nb alloy showed better results compared with pure Ti. The weight gains during the oxidation increase rapidly at temperature above $600^{\circ}C$.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.253-258
• /
• 2012

The characteristics of $Al_2TiO_5$ ceramics were influenced by the additives and the heat treatment that controls the microcrack behavior at grain boundaries. The effect of additives on $Al_2TiO_5$ ceramics were investigated in terms of mechanical properties and thermal expansion at high temperature. The $Al_2TiO_5$ were synthesized at $1500^{\circ}C$, $1550^{\circ}C$ and $1600^{\circ}C$ for 2h by reaction sintering. The formation of $Al_2TiO_5$ phase was increased by additives that enhanced the volume of the microcrack that can lead to low thermal expansion. The mechanical properties of the stabilized $Al_2TiO_5$ ceramics were increased remarkably at $1100^{\circ}C$, $1200^{\circ}C$ and $1300^{\circ}C$ due to the oneset of mechanical healing of grain-bondary microcracks at a high temperature. The amount of microcrack was decreased at lower sintering temperature that causes the increase of mechanical properties at high temperature.

• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.740-746
• /
• 1993

TiO2-SnO2 fine powders prepared by coprecipitation from TiCl4-SnCl4 aqueous solution, and their crystal structures were studied. All the TiO2-SnO2 fine powders calcined at 180~$700^{\circ}C$ showed the complete solid solution between TiO2(rutile structure) and SnO2(rutile structure). This crystal structure of TiO2-SnO2 powders is thought to be originated mainly from the heterogeneous nucleation of Ti-hydroxde on the Sn-hydroxide with coherent structure.

• Journal of the Korean Ceramic Society
• /
• v.22 no.3
• /
• pp.46-52
• /
• 1985

(Ba0.8. Sr0.2) $TiO_3$ semiconducting ceramic with and without Ti-excess composition were prepared by various sintering temperature. The effects of Ti compositions on the samples were discussed in terms of color micro-structure resistivity at room temperature and the positive temperature coefficient resistivity(PTCR). The 1.02mol Ti-excess composition provides better PTCR properties and has uniform micrositructures with 5-7${\mu}{\textrm}{m}$.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.2
• /
• pp.97-104
• /
• 2012

A porous $TiO_2$ pellet was electrochemically converted to the metallic titanium by using a $CaCl_2$ molten salt system at $850^{\circ}C$. Ni-$TiO_2$ and graphite electrodes were used as cathode and anode, respectively. The electrochemical behaviour of $TiO_2$ pellet was determined by a constant voltage control electrolysis. Various reaction intermediates such as $CaTiO_3$, $Ti_2O$ and $Ti_6O$ were observed by XRD analysis during electrolysis of the pellet. Once $TiO_2$ pellet was converted to a porous metallic structure, the porous structure disappeared by sintering and shrinking with increasing the reaction time at high temperature.