• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.65-71
• /
• 2018

There is no significant difference in the initial viscosity of a propellant applied with yellow iron oxide and red iron oxide. In addition, the thermal decomposition rate of the material with added yellow iron oxide is faster than that with the addition of red iron oxide. Specifically, it was confirmed that the pressure exponent was 18% lower at high temperature and high pressure with yellow iron oxide than with red iron oxide. The initial viscosity was lowest at 71% of the large particle to small particle ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.498-503
• /
• 2017

There is no unusual difference in the initial viscosity of the propellant applied with yellow iron oxide and red iron oxide. In addition, the thermal decomposition rate of the material added with yellow iron oxide is faster than that of the addition of red iron oxide. Especially, it was confirmed that the pressure exponent was 18% lower at high temperature and high pressure. The initial viscosity was lowest at 71% of large particle/small particle ratio

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.191-195
• /
• 2009

In the solid rocket propellant combustion, dynamic phase change from solid to liquid to vapor occurs across the melt layer. During the burning surface, micro scale bubbles form as liquid and gas phases are mixed in the intermediate zone between the propellant and the flame. The experimentally measured thickness of this layer called the foam layer is approximately 1 micron at 1 atmosphere. In this paper, we present a new melting layer model derived from the classical phase change theory. The model results show that the surface of burning grows and propagate uniformly at a velocity of $r=ap^n$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.957-967
• /
• 2017

Firing test of the fuel grain for solid fuel ramjet with additives and ignition support material was conducted. Fuel grain consist of HTPB mixed with AP particle 15 wt.%, Boron particle 5 wt.%. To cause the short ignition delay, ignition support consist of $NC/BKNO_3$ and composite propellant was coated to the fuel grain. An oxidant gas having a controlled temperature, pressure and oxygen composition close to the air condition in the ramjet combustor was supplied using the Ethanol blended $H_2O_2$ gas generator. Gas was set to flow at a mass flow rate of 150 g/s and mass flux of $200kg/m^2s$ in the grain port. Through the test, ignition support operated well and ignition delay of 0.5. During the test, stable chamber pressure with 8 bar and high combustion efficiency of 0.86 was confirmed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.2
• /
• pp.16-26
• /
• 2014

T-Burner tests of an Al/HTPB propellant in conjunction with a Pulsed DB/AB Method were conducted to find an acoustic amplification factor. Aluminum-free and aluminum-heavy propellants were examined. Instant surface ignition was successfully made by the use of a supplementary propellant of fractionally higher reaction rate. With the presence of higher aluminum concentration in the propellants, the pressure perturbations were promptly damped down and the pressure fluctuations were no longer dispersive. Addition of aluminum particles into the propellant was advantageous for stabilizing pressure-coupled unstable waves.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.1-6
• /
• 2008

The burning characteristics of HTPB/AP solid propellants were measured by closed bomb of internal volume of 200 cc and 700 cc up to 30,000 psia. The burning rates of closed bomb method showed good agreement with those of strand burner method between 1,000 psia and 5,000 psia, and the sharp increment of pressure exponent(n) around 6,000 psia as a result of testing in accordance with loading densities. The burning rate measured in 200 cc and 700 cc of internal volume of closed bomb agreed well without the relation of internal volume size.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.1
• /
• pp.1-7
• /
• 2004

The precipitation of ultra fine ammonium perchlorate(UFAP) crystals from the N-methyl pyrrolidone(NMP) solutions of ammonium perchlorate(AP) was studied. The characteristics of the precipitated crystals were investigated by means of scanning electron micrograph(SEM), X-ray diffraction(XRD), and thermogravimetric analysis(TGA). When chloroform, methylene chloride and toluene were the precipitants, the product crystals had a mean particle size less than 2$\mu\textrm{m}$. The crystallographical property and thermal decomposition behavior of the prepared UFAP were almost the same as those of the commercial AP.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.79-88
• /
• 2017

Ignition test of the fuel-rich propellant coated with ignition support material in the ramjet combustor condition was conducted. Ignition delay and flame holding was measured. Fuel grain consist of HTPB mixed with AP particle 15 wt.%, Al particle 5 wt.%. To cause the short ignition delay, ignition support consist of $NC/BKNO_3$ and composite propellant was coated to the fuel grain. Ethanol blended $H_2O_2$ gas generator control the temperature, pressure, $O_2$ concentration in the oxidizer gas in the air. Gas is supplied with mass flux of $200kg/m^2s$. Through the test ignition support operated well and ignition delay of 0.6 second and the Flame was sustained.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.2
• /
• pp.72-79
• /
• 2003

A numerical calculation was conducted to estimate and to elucidate the role of the radiative heat flux from metal particles(Al, $Al_2O_3$) on the dynamic extinction of solid propellant rocket where the rapid depressurization took place. Anon-linear flame modeling implemented by the residence time modeling for metalized propellant was adopted to evaluate conductive heat flux to the propellant surface. The radiative heat feed back was calculated with the aid of a modified comvustion-flow model as well. The calculation results with the propellant of AP:Al:CTPB=76:10:14 had revealed that the radiative heat flux is approximately 5~6% of total flux at the critical depressurization rate regardless of chamber geometry (open or confined chamber). It was also found that the dynamic extinction in open geometry could be predicted at the depressurization rate about 45% larger with radiative heat feedback than without radiation. Thus, it should be claimed that even a small amount of radiative flux 5~6% could produce a big error in predicting the critical depressurization rate of the metalized propellant combustion.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1996.05a
• /
• pp.131-137
• /
• 1996

HTPB/AP/Al이 주성분인 2종의 혼합형 추진제를 대상으로 4종의 금속선(Ag, Cu, Al, Ni-Cr)윰 각각 삽입하여 금속선의 직경(0.1~0.8mm)과 연소 압력에 따른 금속선에 인접한 고체 추진제의 연소 속도 증가비($r_w$/$r_sb$)와 압력 지수(n)의 변화를 고찰하였다. 금속선을 추진제에 삽입함으로써 추진제의 $r_w$/$r_sb$ 는 크게 중가하였고, 1000 psia의 압력에서의 최대 6.59배 증가하였다. 그러나 녹는 점이 비교적 낮은 Al 선이나 Ag선은 금속선 직경이 작아짐에 따라 한계 직경에서 $r_w$가 급격히 감소하는 최대값이 존재하였다. 자연 발화 온도와 금속선으로 전달되는 열원인 연소 기체 불꽃 온도로 구성된 무차원군을 Buckingham pi 정리에 의해 구해진 $r_w$/$r_sb$ 에 대한 기존의 무차원 실험식에 추가로 적용하여 계산해 본 결과, 자연 발화 온도는 고려하지 않고 금속선의 녹는 점과 연소 기체의 불꽃 온도를 무시한 Hsing 의 실험식에 의해 계산된 결과보다 표준 편차가 45%이상 줄어듬을 알 수 있었다.