• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.4723-4728
• /
• 2014

In this study, a thermoelectric module (TEM) and a diesel engine were modeled using 1-D commercial software AMESim, and the performance of the TEM was evaluated when the engine was operated under the NEDC driving cycle. The goal of TEM modeling was to investigate not only the waste heat recovery (WHR) rate and energy converting efficiency, but also the heat transfer rate by taking the materials characteristics into account. In addition, a diesel oxidation catalyst (DOC) was designed, and it was found that the waste heat recovery with TEM affects the activation of DOC and alters engine exhaust composition. The simulation indicated that the WHR using TEM is beneficial for decreasing the fuel consumption of vehicles, but the reduction in the exhaust temperature affects the activation of DOC, resulting in an approximately 14% increase in CO and HC emissions. Therefore, the effect of waste heat recovery on the automotive emission characteristics must be considered in the development of automotive engine WHR systems.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.74-84
• /
• 2005

This paper include the investigation of finding the system characteristics of facility by simulating open-type turbo-pump fed system, which has commercial control valves, using AMESIM (Advanced Modeling Environment Simulation) commercial software. After developing a flight-type control valve on the basis of the results, the system characteristics of facility for control and valve tests is estimated. Especially, one of purposes of this paper is to find PID value of each commercial control valve in the facility for system test. To find suitable control logic, PI and PID modes are also compared. This paper also introduces design parameters of valve and equipment for thrust control and TDS simulation, which are using control valves.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.1
• /
• pp.11-19
• /
• 2010

A gas-assisted hydraulic breaker uses both hydraulic and pneumatic energies and the appropriate balance between them mostly effects its performance. Mathematical modeling of the breaker is established and verified by experiment. Through sensitivity analysis using AMESim, the key design parameters are selected, which mostly affect the performance of the breaker. Taguchi method is used to optimize the key design parameters to maximize the output power for long and short strokes through simulation. As the result, the output power as well as the impact energy are increased significantly compared with the existing design. The pressure pulsation in the supply line is reduced to a tolerable level and the dynamic characteristics of the piston displacement is also improved by the optimization.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.299-302
• /
• 1997

The pressure ripples are inevitabilitily generated by a fluctuation of flow rate caused pump mechanism, which occur noises, vibrations, and affect a control performance in tluid pipeline. The method for reduction of pressure ripples has been normally used a accumulator which is installed near the pump generating the pressure ripples. This paper introduces the parallel pipeline as a method to reduce pressure ripples in tluid pipeline, and confirms the usefulness of it in reducing the pressure ripples as compared with the fluid pipeline with a accumulator using AMESim(Advanced Modeling Environment for Simulations) Software.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.5
• /
• pp.125-130
• /
• 2016

A low-recoil direct gun is useful in reducing the fire impulse generated by using a traditional shell. To apply a control equation to an AMESim Model, we have formulated a control equation for a recoil mechanism from the free object diagram. By modeling this equation, we have been able to compare the recoil distance and recoil force of a low-recoil direct gun. Here, we can analyze the recoil characteristics between traditional direct guns and low-recoil direct guns with perforated muzzle brakes. It is possible to mount a low-recoil direct gun with a perforated muzzle brake on a lightweight tracked vehicle by reducing its fire impulse.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.101-102
• /
• 2006

The purpose of this paper is pulsation-analysis of the swash plate type axial piston pump for excavator and the method of side branch hose application, which is used normally in construction equipments. In this paper, draw the mathematical modeling for pressure pulsation mechanism of the swash plate type axial piston pump for excavator, expression the flow pulsation in the pipelines by transfer matrix method, programmed simulation for pulsation by AMEsim software, and the reliability of that was verified by the comparison with the experimental results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.1
• /
• pp.87-93
• /
• 2014

This paper provides a methodology for extracting design data from the three-dimensional design software SolidWorks$^{(R)}$, which is based on the existing trochoid pump design equations that are used by hydraulic field engineers. The data extracted from the SolidWorks$^{(R)}$ model are input to a hydraulic analysis software AMESim model to determine the design factors that can influence the properties of a trochoid pump. On the basis of the simulation results, this paper proposes a method to reduce the flow loss by adjusting the outlet angle of the trochoid pump. This proposal was verified by using actual experimental results, which confirmed that adjusting the outlet angle can increase the flow rate. Hence, the results presented in this paper can contribute to the prototyping of a trochoid pump by reducing the cost associated with a trial-and-error design.

• Journal of Drive and Control
• /
• v.15 no.3
• /
• pp.49-56
• /
• 2018

Construction machinery is used to improve productivity in civil engineering work and construction work, and it is a lengthy operation, and consumes considerable fuel to cope with large loads. As a result, productivity and fuel consumption of the construction machine become the main deciding factors. In the hydraulic system of the excavator, the main control valve is the most critical position for control. The flow distribution for control performance is achieved by the metering orifice, that causes critical energy loss. To improve this, we propose a combination of a three port proportional pressure reducing valve and a poppet type flow control valve as an IMV to replace the existing spool type MCV. To validate the proposal, we analyze static characteristics by modeling mathematically, and analyze dynamic characteristics. Simulation using the AMESim software on the regeneration circuit of the boom cylinder up-down operation, verifies the energy-saving effect compared to the existing MCV when IMV is used.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.8-14
• /
• 2014

The transmission control method of a small forklift is classified into a pilot control method and a direct control method. In the pilot control method, the complex hydraulic circuit consists of many components, making the production process too costly and time consuming. The direct control method contains fewer components that can be configured to simple hydraulic circuits. As another advantage, the input profile easily changes the shift sensitivity of the transmission. Therefore, this research considers the characteristics of the direct control method in the development of hydraulic system design. This paper will present a simulation of the direct control transmission using AMESim. First, modeling of the direct control method is obtained and simulated with real parameters. The simulation results then are carried out and compared with the experimental results to verify and analyze the characteristics of the direct control method.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.5
• /
• pp.341-348
• /
• 2016

The solenoid valve is used widely across various industries; however, solenoid valves for use in high-temperature environments have to be highly specified, such as those used in thermal power plants and steel mills. As such, we have developed a solenoid valve, using an already developed solenoid, to allow for more specific use. In this type of development method, use of 3D printing is very effective, allowing for a reduction in errors in design and production. This study includes a mathematical model of the solenoid valve. Then, the simulation from the mathematical model was performed using the AMESim (Advanced Modeling Environment for Simulation of Engineering Systems). We made a prototype valve using the simulation results and also measured the flow rate and dynamic performance.