• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.772-779
• /
• 2000

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with a different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused a abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.4
• /
• pp.42-50
• /
• 1995

To study the effect of welding methods on the Stress Corrosion Cracking (SCC) behavior of welded AISI type 316L and 304 austenitic stainless steel, the Slow Strain Rate Technique(SSRT) has been adopted in the boiling 45 wt% $MgCl_2$ solution. The results are as follows. 1) Welded sections are more susceptible than base metal in SCC, and the rank of SCC, and the rasistance in welding method is TIG, MIG, $CO_2$ and ARC. 2) The Ultimate tensile strength(UTS) and the strain of both base metal and welded joint are reduced as decreasing extension rate. 3) The SCC resistance of 316L base metal and welded sections are superior than that of 304. 4) The tendency of pitting and the SCC suseptibility are agreed well, and the SCC site is welded deposit section in 316L whereas HAZ in 304.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.192-193
• /
• 2009

CrN 코팅막은 고온에서 치밀한 Cr2O3 확산방지막을 형성함으로 $800^{\circ}C$까지 기계적성질을 유지할 수 있다. 본 실험에서는 Ar, N2, 그리고 $O_2$ 가스 분위기에서 AIP(Arc Ion Plating) 기법에 의해 다양한 조성의 Cr-O-N 박막을 Si(200)과 AISI 304 기판 위에 증착되었다. Cr-O-N 코팅막은 47.4at% 미만의 산소함량을 포함 할 때까지 B1구조를 유지하였고 코팅막 내 산소함량 24.6at%에서는 강한 XRD peak intensification을 나타내었다. 47.4at%에서는 결정상을 전혀 찾아볼 수 없는 전이구조를 나타내었고, 그 이상의 산소함량에서는 Cr22O3 결정상을 나타내었다. Cr-O(17at%)-N 조성의 코팅막에서는 (200)배향의 Grain 크기 증가 및 압축잔류응력이 증가하였으나, 그 이상의 산소함량에서는 점차 감소하였다. Cr-O(24.6at%)-N 조성의 코팅막이 가장 높은 경도를 나타내었고, 산소함량이 증가할수록 점차 향상된 마찰특성을 보였다.

• Journal of Power System Engineering
• /
• v.11 no.4
• /
• pp.92-97
• /
• 2007

This study aims at investigating the wear behavior of thermally sprayed Ni-based self-flux alloy coatings against different counterparts. Ni-based self-flux alloy powders were flame-sprayed onto a carbon steel substrate and then heat-treated at temperature of $1000^{\circ}C$. Dry sliding wear tests were performed using the sliding speeds of 0.2 and 0.8 m/s and the applied loads of 5 and 20 N. AISI 52100, $Al_2O_3$, $Si_3N_4$ and $ZrO_2$ balls were used as counterpart materials. Wear behavior of Ni-based self-flux alloy coatings against different counterparts were studied using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDX). It was revealed that wear behavior of Ni-based self-flux alloy coatings were much influenced by counterpart materials.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.78-86
• /
• 1995

The silicon nitride based ceramic cutting tool materials have been fabricated by gas pressure sintering (GPS) or hot pressing (HP). Their mechanical properties were measured and the effect of the fabrication variables on the properties were examined. Also, effect of adding TiN or TiC particulates on the mechanical properties of the silicon nitride ceramics were investigated. Ceramic cutting tools (ISO 120408) were made of the sintered bodies. Cutting performance test were performed on either conventional or NC lathe. The workpieces were grey cast iron, hardened alloy steel (AISI 4140, HRc>60) and Ni-based superalloy (Inconel 718). The results showed that fabrication variables, namely, sintering temperature and time, exerted a strong influence on the microstincture and mechanical properties of the sintered body, which, however, did not make much difference in wear resistance of the tools. High hardness of the tool containing TiC particulates exhibited good cutting performance. Extensive crater wear was observed on both monolithic and TiN-containing silicon nitride tools after cutting the hardened alloy steel. Inconel 718 was extremely difficult to cut by the current cutting tools.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.417-426
• /
• 2001

The effect of silver particle introduction on the rolling friction of AISI 52100 steel pairs has been investigated. Experiments ware performed in dry conditions using a thrust bearing-type rolling test rig at a load range of 12-960 N and a sliding velocity range of 8-785 mm/sec with pure (99.99%) silver particles. Results showed that introduced silver particles formed transfer layers, which protected the virgin bearing surfaces and resulted in the low lolling friction. By changing the quantity of silver particles, transitions in the rolling friction were found. Results also showed that the variations in normal load and rolling speed also affected the rolling friction behavior. Analyses of SEM and EPMA showed that the formation the transfer layer was mainly governed by the silver particle quantity, normal load and rolling speed, and this resulted in the different behavior of rolling friction. In this study, it was found that the low and stable rolling friction was resulted from the, shakedown phenomena occurred at the silver transfer layer.

• Journal of Welding and Joining
• /
• v.11 no.1
• /
• pp.21-32
• /
• 1993

A cracking failure of a austenitic stainless steel elbow in a naphtha cracking line in a petrochenmical plant occurred, resulting in leakage of organic compound flowing inside the elbow. Due to the failure, emergency shutdown of the plant was enforced to repair the troubled part of the line. The repair cost as well as production loss during the unscheduled plant shutdown has cost the company a great amount of financial loss. In this studies, a failure analysis of the cracked elbow was performed using NDT, chemical analysis, microstructural analysis including optical microscopy as well as scanning electron microscopy with EPMA, mechanical testings such as tensile testing, hardness testing and Charphy impact test fractography. The results indicated that several problems such as a welding defect and presence of a detrimental phase which was found to be relate to improper postforming heat treatment process was identified and the failure was concluded to be due to a low temperature embrittlement of the defect-containing elbows.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.871-877
• /
• 2012

New materials widely used for automobile related industry, aircraft, space development area are mostly high hardness materials. The hardness value of some hardened materials is over HRC45 and machining of this hardened materials is called as hard turning. Hard turning has its advantage on processing flexibility, cycle time and tool cost reduction. Also this process obtains high efficiency in processing and precise surface roughness through application of the CBN tools. In hard turning process with CBN tool, surface integrity is the important factor for considering the design of machine part and component under high stress and load conditions. A purpose of this study is to analyze optimal condition in hard turning process of AISI 52100 steel (HRC62) with high CBN and low CBN on turning characteristics, tool wear mechanism comparison and surface integrity.

• Transactions of Materials Processing
• /
• v.17 no.8
• /
• pp.619-626
• /
• 2008

In this study, design methodology to determine optimal shape of the anvil in sizing press process has been proposed to minimize crop length of the AISI 1010 slab in horizontal rolling after width reduction. Shape of anvil were selected to 12 cases by design of experiment, and the dog-bone shapes and the crop length were determined by FE-analysis. Also, the anvil shape, which has minimum crop length, were determined by artificial neural network(ANN). As a result of FE-analysis, it can be seen that the crop length was increased with increasing center thickness in the dog-bone shape after width reduction. The anvil shape which has minimum crop length, was estimated to ${\theta}_{1}=21^{\circ}{\theta}_{2}=14^{\circ}$ by FE-analysis and ANN.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.4
• /
• pp.241-248
• /
• 2002

Hardfacing layers of Stellite 6 alloy with different molybdenum content are deposited on AISI 1045 carbon steel using plasma transferred arc welding (PTAW). The properties of the hardfacing layer are investigated in order to clarify the effect of molybdenum addition to the cobalt-base alloy. With an increase in molybdenum contents, the size of Cr-rich carbides in the interdendritic region is abruptly refined, but volume fraction of the carbide slightly increases. Also, with an increase of Mo, $M_{6}$ C type carbides are formed instead of Cr-rich $M_{7}$ $C_{3}$ type carbided, and this microstructural change enhanced the mechanical properties of Stellite 6 alloy.