• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.136-140
• /
• 1999

Measurements of AE signals caused by partial discharges were performed by using an ultrasonic measurement technique to diagonise the electrical treeing deterioration in XLPE cable. We also examined the partial discharge magnitude and AE signals(peak-to-peak) with the increase of the deterioration time. From these results, it was found that AE signal due to partial discharge can be greatly detected at the peak value of positive polarities prior to the breakdown voltages, and the magnitude of AE signals was closely related to the current pulses by the increase of deterioration, and it appeared that AE signals(peak-to-peak) was proportional to partial discharge magnitude. Attenuation and time-delaying characteristics of ultrasonic signals propagated in various polymers sample by using ultrasonic oscillation and receiving systems are also reported as a basic data of ultrasonic measurements in XLPE cable.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.246-250
• /
• 2000

In this paper, Frequency spectra of AE(acoustic emission) signals generated from the magnetizing and the load currents in the actual operating cast-resin power transformer of 500[kVA] under distribution system of22.9[kV] were also analysed to distinguish the AE signals due to void discharges from the magnetic circuit noises in the core of cast-resin power transformer. As the experimental results, we could distinguish the AE signals whether those signals were caused due to the void discharges or due to the magnetic circuit noises by analyzing the frequency spectrum of AE signals. Frequency spectra of AE signals generated from the cast-resin power transformer in operation due to both the magnetizing and the load currents appeared in the range of 40-120[khz].

• 대한토목학회논문집
• /
• 제26권5A호
• /
• pp.917-925
• /
• 2006

AE기법을 이용하여 PSC보부재에 대한 음파의 전파속도와 음원위치 산정방법의 타당성을 알아보기 위한 실험을 수행하였다. 이를 위해 길이가 5m 인 PSC보 콘크리트 표면에 7개의 AE센서를 부착하였으며, 슈미트 햄머를 이용하여 콘크리트 표면에 인위적인 충격을 가하였다. 음파의 전파속도는 각각의 AE센서로부터 감지한 음파의 도달시간 차이와 음원과 센서와의 거리 차이를 이용하여 산정하였다. 또한 각 AE센서로부터 감지된 음파의 도달시간과 음파의 전파속도를 토대로 최소제곱법을 이용하여 역으로 음원 발생위치를 산정해 보았다. 실험결과 프리스트레스트콘크리트 매질에 대한 음파의 평균전파속도는 대략 4,000 m/sec 정도이며, 음원과 AE 센서 사이의 거리가 길어짐에 따라 음파의 감쇠현상에 의해 속도가 감소되었다. 최소제곱법을 이용한 음원위치 산정결과, 음파의 전파속도를 전체 AE센서의 평균전파속도를 이용하는 경우보다, 각 AE센서로 부터 산정된 음파의 전파속도를 이용하는 경우 오차가 감소되는 것을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.365-368
• /
• 1995

Rotary Compressor has many AE(Acoustic Emission) sources according to condition of parts because it is operated with combination of various parts. In this study, analysis of AE raw signal generated form Rotary compressor which artificially-made parts inflicted abnormal condition was carried out. AE raw signals were acquired form high-speed A/D board, and many burst type signals were observed. By analyzing burst type signals which is caused form internal AE source,efficient AE parameters for monitoring and diagnosis were presented.

• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.26-33
• /
• 1999

Automatic monitoring of cutting process is one of the most important technologies for increasing the stability and the reliability of unmanned manufacturing system. In this study, basic methods which use the acoustic emission (AE) signals and cutting forces were proposed to monitor flank wear (width of flank wear) quantiatively. First, in order to detect flank wear, it was investigated that the influence of cutting conditions, that is, cutting velocity, feed and depth of cut, on AE signals (${AE_rms}$) and cutting forces. Furthermore, the relation between flank wear and the measured signals (${AE_rms}$, cutting force) was discussed.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권1호
• /
• pp.44-51
• /
• 2000

In this paper, using a wide-band AE sensor with the frequency range from 100[kHz] to 1.5[kHz], the frequency spectra of AE signals generated from the corona discharges of the needle-plane gap and from the partial discharges of an epoxy void were analyzed to determine the proper ultrasonic sensor with optimum frequency range according to the patterns of corona discharges. We also examined the propagation characteristics of AE signals in oil and the relationship between the magnitude of corona discharge and the magnitude of AE signals in peak-to-peak value under the application of 60[Hz] ac high-voltage. From these results, the main frequency spectra of AE signals emitted from the corona discharges of the needle-plane gap were about 130[kHz] by the fast fourier transform, but the main frequency spectra appeared to be 230[kHz] in the partial discharges of an epoxy void. The magnitude of AE signals was proportional to the magnitude of corona discharge and discharge current pulse with increasing the applied voltages.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.15-21
• /
• 1996

This study is focused on the prediction of appropriate tool life by clarifying the correlation between progressive tool wear and AE(Acoustic Emission) signals, while cutting stainless steel by end mill on the machining center. The results of this study were that RMSAE tends to increase linearly along with the increase of the cutting speed, and it was more sensitive to depth of cut than to the variation of feed rate at the same cutting conditions, and RMSAE increases around 0.21mm flank wear hereby AE-HIT also increases. AE signals depend upon tool wear and fracture from the above results. Therefore, the AE signals can be utilized in order to monitor the tool condition.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.51-52
• /
• 2007

This paper compared wired Acoustic Emission (AE) signals with wireless AE signals. According to the material and process condition, each process signal has distinguishable characteristic to show each removal phenomenon. Therefore, wired and wireless AE sensors having different bandwidth are complementary for CMP process monitoring. Especially, the AE sensor was used to investigate abrasive and molecular-scale phenomena during CMP process, which was compatible to acquire high level frequency. In experiment, wireless AE system was used to get signals in rotary system, using bluetooth. But, it is possible to acquire only RMS signals, which can not analyze abrasive and molecular-sale phenomena. Second, wired AE system was installed using mercury slip-ring, which is suitable not only for rotation equipment but also for acquiring original signals. The acquired signals were analyzed by FFT for understanding of abrasive and molecular revel phenomena in CMP process, finally, we verified that two types of AE sensor with different bandwidth were complementary for CMP process monitoring.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2338-2340
• /
• 1999

In this paper measurements of AE (Acoustic Emission) signals caused by corona discharge were performed to analyze the electrical deterioration in oil. We also examined the relationship between discharge magnitude and peak-to-peak value of AE signals to diagnose the deterioration of liquid dielectrics. From these results, Vpp(peak to peak value) of AE signals was proportional to corona discharge magnitude. The main frequency band of AE signals in oil appeared to 130[kHz].

• Journal of Mechanical Science and Technology
• /
• 제20권2호
• /
• pp.197-204
• /
• 2006

The purpose of this study is to evaluate the AE characteristics for the basemetal, PWHT (post-weld heat treatment) and weldment specimens of SA-516 steel during fracture testing. Four-point bending and AE tests were conducted simultaneously. AE signals were emitted in the process of plastic deformation. AE signal strength and amplitude of the weldment was the strongest, followed by PWHT specimen and basemetal. More AE signals were emitted from the weldment samples because of the oxides, and discontinuous mechanical properties. AE signal strength and amplitude for the basemetal or PWHT specimen decreased remarkably compared to the weldment because of lower strength. Pre-cracked specimens emitted even lower event counts than the corresponding blunt notched specimens. Dimple fracture from void coalescence mechanism is associated with low-level AE signal strength for the basemetal or PWHT. Tearing mode and dimple formation were shown on the fracture surfaces of the weldment, but only a small fraction produced detectable AE.