• 제목/요약/키워드: AE counts

검색결과 122건 처리시간 0.034초

AE에 의한 WA계 비트리파이드 및 레지노이드 결합제 연삭숫돌의 결합도 평가 (Evaluation of Grade of WA-Vitrified and Resinoid Bond Grinding Wheels by Acoustic Emission)

  • 정인근;임영호;권동호
    • 한국정밀공학회지
    • /
    • 제12권9호
    • /
    • pp.74-85
    • /
    • 1995
  • The purpose of this paper is to evaluate the grade of WA vitrified and resinoid bond grinding wheels by the sue of AE measuring system. When the manufactured 48 kinds of specimens were scratched by the method of OKOSHI'S grade test, the relationship between the amount of bit scratch depth of grinding wheel specimens and the character- istics of AE signals, and the relationship of AE counts and grade were considered as fololws; (1) The higher the grades are AE cumlulative event counts N and AE event count rate n, the smaller the values tend to be. But A $E_{rms}$is in reverse. (2) In the case of same grade, the smaller the grain size is, the higher the value of AE cumulative event counts N and A $E_{rms}$is results of comparison and observation. The grinding wheel with lower elasticity and with higher percentage of pore detected higher value of AE cumula- tive event counts N than with higher elasticity and lower percentage of pore. But A $E_{rms}$ is in reverse. (3) AE cumulative event counts N and bit scratch depth h have normally one to one correspondence. (4) It can be expected that quantitative evaluations of grade by using AE have been carried out by the wave observation of AE signal in line with the relationship between load speed of bit and AE cumulative event counts N & AE event count rate n.' AE event count rate n.ate n.

  • PDF

이종강관 마찰용접의 소성변형 중 발생된 초기 AE양이 용접품질 제어에 미치는 영향에 관한 연구 (Effects of Initial AE Counts During Plastic Deformation in Friction \elding of Dissimilar Steel Tubes on the Weld Quality Control)

  • 오세규;김동조;정락기
    • Journal of Welding and Joining
    • /
    • 제1권2호
    • /
    • pp.69-75
    • /
    • 1983
  • Both in-process quality control and reliability of the weld is one of the major concerns is applying friction welding. No reliable nondestructive monitoring method is available at present to determine the weld quality particularly in process of production. So that, this paper presents an experimental examination and quantitative analysis for the effects of initial acoustic emission(AE) counts on the weld strength relating to the rotating speed as a new approach which attempts finally to develop an on-line quality monitoring system design for friction welds using AE techniques. As one of the important results, it was well confirmed that the initial AE counts occurring during plastic deformation period of welding were quantitatively correlated with reliability at 95% confidence level to the joint strength of welds, tube-to-tube (SM 20 C to STS 304) and then an AE technique using the initial AE counts can be reliably applied to in-process strength monitoring of the weld.

  • PDF

압력용기용 고온재료의 마찰용접 최적화 및 AE에 의한 실시간 품질평가( I ) (Friction Welding Optimization of Elevated Temperature Materials for Pressure Vessels and Its Quality Evaluation by AE)

  • 김헌경;공유식;이연탁;유인종;오세규
    • 한국해양공학회:학술대회논문집
    • /
    • 한국해양공학회 2001년도 춘계학술대회 논문집
    • /
    • pp.301-306
    • /
    • 2001
  • In this paper, friction welding optimization for 1Cr0.5Mo to STS304 and AE applications for the weld quality evaluation were investigated The important results of this study are as follows : 1. The techiques for dissimilar friction welding optimization if the elevated temperature materials 1Cr0.5Mo and STS304 and its real-time weld quality evaluation by AE were developed, considering on both strength and toughness. 2. Quantitative relationship was identified among welding condition, weld quality and cumulative AE counts.

  • PDF

음향방출법에 의한 고 장력강 용접부의 부식손상 특성 평가 (Characterization of Stress Corrosion Cracking at the Welded Region of High Strength Steel using Acoustic Emission Method)

  • 나의균;김훈
    • 비파괴검사학회지
    • /
    • 제23권3호
    • /
    • pp.212-219
    • /
    • 2003
  • 본 연구의 목적은 음향방출법을 이용하여 고 장력강 용접부의 응력부식균열특성을 평가하는데 있다. 이를 위해 용접재와 후열처리재를 대상으로 인공해수에서 저 변형률로 하중을 가하면서 응력부식균열을 일으키고, 동시에 음향방출법에 의해 손상과정을 감시하였다. 부식환경은 전위계에 의해 제어되었으며, 시험편에는 각각 -0.8V와 -1.1V의 전위 값을 가하였다. -0.8V인 부식환경 하에서 일층 용접부는 후열처리재에 비해 단위 시간당 AE counts수가 훨씬 많이 발생하였으며, 응력부식균열과정에서 균열의 발생 및 합체가 가장 활발하게 이뤄지고 있음을 누적 AE counts의 결과로부터 확인할 수 있었다. 가해진 전위 값이 -1.1V인 경우, 일층 용접재의 파단시간은 이층 용접재에 비해 줄었고, AE counts수는 이층 용접재에 비해 현저히 많이 발생하였다 AE진폭 범위는 -0.8V 일층 용접재에서 가장 높았고, -1.1V 일층 용접재에서 가장 작은 값을 보였는데, fractography분석결과 AE 진폭 범위는 균열의 크기 및 폭과 밀접한 관계가 있음을 알 수 있었다.

탄소섬유 복합재료의 AE 특성에 관한 연구 (A Study on the AE Characteristics of the Carbon Fiber Composite Material)

  • 옹장우;이영신;심봉식;지용관;주영상
    • 대한기계학회논문집
    • /
    • 제13권1호
    • /
    • pp.105-114
    • /
    • 1989
  • 본 연구에서는 카본/에폭시 프리프렉으로부터 제작된 적층판을 사용하여 인장시험시 발생하는 AE특성과 파괴거동을 비교 검토하고 이들을 통하여 탄소섬유 복합재료의 파손특성과 AE법의 유용성을 규명하고자 한다.

Damage characterization of hard-brittle rocks under cyclic loading based on energy dissipation and acoustic emission characteristics

  • Li, Cheng J.;Lou, Pei J.;Xu, Ying
    • Geomechanics and Engineering
    • /
    • 제31권4호
    • /
    • pp.365-373
    • /
    • 2022
  • In order to investigate the damage evolution law of rock specimens under cyclic loading, cyclic loading tests under constant loads with different amplitudes were carried out on limestone specimens with high strength and brittleness values using acoustic emission (AE) technology and the energy evolution and AE characteristics were evaluated. Based on dissipated energy density and AE counts, the damage variable of specimen was characterized and two damage evolution processes were analyzed and compared. The obtained results showed that the change of AE counts was closely related to radial deformation. Higher cyclic loading values result in more significant radial strain of limestone specimen and larger accumulative AE counts of cyclic loading segment, which indicated Felicity effect. Regarding dissipated energy density, the damage of limestone specimen was defined without considering the influence of radial deformation, which made the damage value of cyclic loading segment higher at lower amplitude loads. The damage of cyclic loading segment was increased with the magnitude of load. When dissipated energy density was applied to define damage, the damage value at unloading segment was smaller than that of AE counts. Under higher cyclic loading values, rocks show obvious damage during both loading and unloading processes. Therefore, during deep rock excavation, the damages caused by the deformation recovery of unloading rocks could not be ignored when considering the damage caused by abutment pressure.

음향방출법에 의한 항공기용 가스터빈 재료의 크리프 수명예측 평가 (Evaluation on Creep Life Prediction of Aircraft Gas Turbine Material by AE)

  • 공유식;윤한기;오세규
    • 동력기계공학회지
    • /
    • 제6권1호
    • /
    • pp.55-60
    • /
    • 2002
  • There has been no report on the life prediction for gas turbine materials at high temperatures based on the creep properties and their relationship with the AE(acoustic emission) properties as a means of real-time non-destructive testing. One of the important issues is thus to develop a reliable method of evaluating creep properties by the AE technique. In this paper, the real-time evaluation of high temperature creep time and AE cumulative counts for nickel-based superalloy Udimet 720 was performed on round-bar type specimens under pure load at the temperatures of 811, 922 and 977K. The total AE cumulative counts until the starting point of secondary creep($N_1$) and that of tertiary creep($N_2$) have quantitative relationship with the tertiary creep time and the rupture time. It is thus possible to construct the life prediction system based on creep and the prevention system of tertiary creep by using AE technique.

  • PDF

AE방법에 의한 구상화흑연(球狀化黑鉛) 주철재의 파괴기구 구명(究明) (An Investigation of Fracture Mechanism of Spheroidal Graphite Cast Iron by Acoustic Emission Method)

  • 김상철;함경춘;오범석
    • 비파괴검사학회지
    • /
    • 제6권2호
    • /
    • pp.17-36
    • /
    • 1987
  • In this experimental research, fracture mechanisms of spheroidal graphite cast iron (As Cast, annealed and normalized) were investigated by using Acoustic Emission (AE) technique. In this study, the data (AE signal) are digitized and processed with the 8 bits micro-computer (APPLE II) connected to the AE measuring device without data processing unit. The source of AE signal was estimated by fractography analysis. The results obtained in this experimental study are summarized as follows : For the heterogeneous materials (spheroidal graphite cast iron) with inclusions which may considered as cracks, it is found that low and high AE amplitude appear simultaneously and the load is found to be fluctuated in the final stage of deformation. But the lad is not fluctuated in tension test with low AE amplitude only. AE is measured within elastic region and it is confirmed that 0.2% offset yield load agrees approximately with the load point where AE counts decrease steeply after the point of maximum AE counts.

  • PDF

AE 진폭분포를 이용한 고장력강의 파괴특성평가 (Evaluation of Fracture Behavior of High Tension Steel by AE Amplitude Distribution)

  • 서정원;석창성;김영진;박지우
    • 한국정밀공학회지
    • /
    • 제16권5호통권98호
    • /
    • pp.175-185
    • /
    • 1999
  • Acoustic emission(AE) measurement was carried out to evaluate the fracture behavior of high tension steel. Fracture toughness $K_{AE}$ could be determined reasonably by using the load value corresponding to an abrupt change of the accumulated AE counts AE emitted from the test specimens. AE characteristics of the base metal, the weld metal and the heat-affected zone could be distinguished using a constant value b which represented the AE amplitude distribution, Consequently the structure integrity can be evaluated by variation of the constant b at the load level. In addition it was found that AE signals due to crack growth have high amplitude but low rise time and duration.

  • PDF

음향방출법(AE)에 의한 기계요소재의 마찰용접 품질 실시간 평가 (REAL-TIME QUALITY EVALUATION OF FRICTION WELDING OF MACHINE COMPONENTS BY ACOUSTIC EMISSION)

  • SAE-KYOO OH
    • 대한용접접합학회:학술대회논문집
    • /
    • 대한용접접합학회 1995년도 특별강연 및 추계학술발표 개요집
    • /
    • pp.3-20
    • /
    • 1995
  • Development of Real-Time Quality Evaluation of Friction Welding by Acousitc Emission : Report 1 ABSTRACT : According as the friction welding has been increasingly applied in manufacturing various machine components because of its significant economic and technical advantages, one of the important concerns is the reliable quality monitoring method for a good weld quality with both joint strength and toughness in the process of its production. However no reliable nondestructive test method is available at present to determine the weld quality particularly in process of production. So this paper presents an experimental examination and quantitative analysis for the real-time evaluation of friction weld quality by acoustic emission, as a new approach which attempts finally to develop an on-line quality monitoring system design for friction welds using AE techniques. As one of the important results, it was confirmed, through this study, that AE techniques can be reliably applied to evaluating the friction weld qualify with 100% joint strength, as the cumulative AE counts occurring during welding period were quantitatively correlated with reliability at 95% confidence level to the joint strength of welds. Real-Time Evaluation of Automatic Production Quality Control for Friction Welding Machine : Report 2 Abstract : Both in-process quality control and high reliability of the weld is one of the major concerns in applying friction welding to the economical and qualified mass-production. No reliable nondestructive monitoring method is available at present to determine the real-time evaluation of automatic production quality control for friction welding machine. This paper, so that, presents the experimental examinations and statistical quantitative analysis of the correlation between the initial cumulative counts of acoustic emission(AE) occurring during plastic deformation period of the welding and the tensile strength of the welded joints as well as the various welding variables, as a new approach which attempts finally to develop an on-line (or real-time) quality monitoring system and a program for the process of real-time friction welding quality evaluation by initial AE cumulative counts. As one of the important results, it was well confirmed that the initial AE cumulative counts were quantitatively and cubically correlated with reliability of 95% confidence level to the joint strength of the welds, bar-to-bar (SCM4 to SUM31, SCM4 to SUM24L) and that an AE technique using initial AE counts can be reliably applied to real-time strength evaluation of the welded joints, and that such a program of the system was well developed resulting in practical possibility of real-time quality control more than 100% joint efficiency showing good weld with no micro-structural defects.

  • PDF