• 대한기계학회논문집
• /
• 제13권2호
• /
• pp.252-256
• /
• 1989

본 연구에서는 탄성-소성 피로파괴 시험을 하여 dN/dn과 .DELTA.J의 관계와 dN/과 da/dn의 관계에 대한 실험식을 얻고 이론적인 해석결과와 비교 검토하고자 한다.

• 한국기계가공학회지
• /
• 제3권1호
• /
• pp.28-37
• /
• 2004

An on-line monitoring system of endmill failure such as weal, chipping, and fracture is developed using AE, cutting force Characteristic variations of AE and cutting force signals due to endmill failure are identified as follows. When endmill fracture occurs, AE count rate shows a rapid Increase in conjunction with a subsequent decrease while a standard deviation of the principal cutting force Increases significantly. The increase of AE count rate precedes the Increase of standard deviation of principal cutting force. Chipping results in relatively small increase and decrease of AE count rate without any significant variation of the cutting force Gradual increase of AE count rate and mean principal cutting force are Identified to be related with the wear of cutter. A cutter fracture detection algorithm is developed based on the present results. The signals me normalized to enhance the applicability of the algorithm to Wide those of fresh cutters, and qualitative characteristics of AE signals encountered at the moment of fracture are employed. It is demonstrated that the algorithm can detect the cutter fracture successfully.

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.112-118
• /
• 1997

Characteristics of AE(Acoustic Emission) signal is related to cutting conditions, tool materials, and tool geometry in metal cutting. Relation between AE signal and tool wear was investigated experimentally. Experiment is carried out by interrupted cutting for SCM420 workpiece with TiN coating tool on HSS material. AE RMS voltage and count per event were increased according to tool wear. The major results are as follows : 1) AE RMS value is nearly constant as cutting speed changes, but is rapidly increase as feed rate increases. 2) AE RMS value and Count per Event increase as tool wear increases. 3) It is more effective to monitor tool wear by Incremental rate of AE RMS value than by Incremental rate of count per event.

• 한국정밀공학회지
• /
• 제20권10호
• /
• pp.41-46
• /
• 2003

This paper deals with the possibility of tap breakage detection by AE sensor. AE signals in the tapping were not seldom generated in low speed but reflected the tapping process exactly in high speed. Using AE raw signals sampled in 500kHz, AE RMS and AE count rate was computed in software. When the converting time of AE RMS is less than 10ms, we could distinguish between normal cutting and tap breakage. And AE count rate was more exact when the converting time is greater than 1ms. When two methods were compared to each other, AE count rate was more accurate.

• 한국가구학회지
• /
• 제10권2호
• /
• pp.73-78
• /
• 1999

This paper describes the relationship between the bending strength properties of sloped finger-jointed woods and the acoustic emissions(AEs) generated during the test. Rhus verniciflua pieces were cut in sloped-finger types and glued with three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The AE cumulative event count and cumulative count were measured during the bending test. The results were as follows: The lower the bending strength(load) was, the generation time of AE event count got and the higher the increasing rate of AE event count became in the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl acetate oilic urethane resin adhesives. Therefore, the slope from load-AE cumulative event count was very steep. The patterns of AE event count and count were very similar. The relationship between the MOR and the AE parameter from load and AE cumulatve event count in the early stage of the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl and oilic urethane resin adhesives was much greater than that between the MOE and the MOR. Therefore, the AE signals obtained during bending test are useful for estimating the strength of sloped finger-jointed Rhus verniciflua specimens.

• 대한기계학회논문집
• /
• 제6권4호
• /
• pp.377-383
• /
• 1982

Acoustic emission (AE) of a high strength steel (SCM-4) was measured under stress corrosion cracking(SCC) test at a constant displacement in 3.5% artificial NaCl solution of 18.deg.C, 45.deg.C and 60.deg.C, respectively. The results are as follows; During the SCC test, AE is detected and AE count rate is approximately proportional to the crack growth rate. Even though crack is not propagated macroscopically, AE is detected. The crack growth rate of SCC and the AE count rate are higher for the solution of higher temperature, 45.deg.C and 60.deg.C, than for the solution of lower temperature, 18.deg.C. In the early stage of SCC, AE total counts mostly depend on crack growth. In the later stage, however, AE mostly depends on the film fracture and the dissolution of anode.

• Journal of the Korean Wood Science and Technology
• /
• 제27권1호
• /
• pp.30-36
• /
• 1999

소나무를 재료로 경사핑거접합법으로 레소시놀계수지, 유용성 우레탄수지, 초산비닐수지, 초산비닐과 아크릴을 혼합한 수지접착제롤 사용하여 제작한 시험재의 휨강도 성능과 휨 시험시 발생하는 AE 특성에 대한 연구결과는 다음과 같다. 초산 비닐, 유용성 우레탄 수지접착제를 사용한 소나무경사 핑거접합재의 하중과 AE 사상총수는 휨 강도가 낮을수록 빠른 시기부터 AE가 발생하고 AE의 증가속도가 빨라 하중-AE 사상총수의 관계곡선의 기울기가 급격하게 나타났다. 레소시놀 수지 접착제로 제작한 시편은 아주 낮은 하중에서부터 하중이 증가함에 따라 연속적으로 AE가 발생하였고 발생수도 많았다. 경사 핑거접착제의 휨 하중과 AE 특성간에는 서로 잘 대응되어 휨강도 측정이나 보정은 휨 탄성계수로서는 예측이 어렵지만 하중과 AE, 사상총수의 초기 치로부터 얻어지는 AE지표 치로서 휨 강도의 예측이나 보증이 가능 할 것으로 판단된다.

• 한국정밀공학회지
• /
• 제12권9호
• /
• pp.74-85
• /
• 1995

The purpose of this paper is to evaluate the grade of WA vitrified and resinoid bond grinding wheels by the sue of AE measuring system. When the manufactured 48 kinds of specimens were scratched by the method of OKOSHI'S grade test, the relationship between the amount of bit scratch depth of grinding wheel specimens and the character- istics of AE signals, and the relationship of AE counts and grade were considered as fololws; (1) The higher the grades are AE cumlulative event counts N and AE event count rate n, the smaller the values tend to be. But A $E_{rms}$is in reverse. (2) In the case of same grade, the smaller the grain size is, the higher the value of AE cumulative event counts N and A $E_{rms}$is results of comparison and observation. The grinding wheel with lower elasticity and with higher percentage of pore detected higher value of AE cumula- tive event counts N than with higher elasticity and lower percentage of pore. But A $E_{rms}$ is in reverse. (3) AE cumulative event counts N and bit scratch depth h have normally one to one correspondence. (4) It can be expected that quantitative evaluations of grade by using AE have been carried out by the wave observation of AE signal in line with the relationship between load speed of bit and AE cumulative event counts N & AE event count rate n.' AE event count rate n.ate n.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.938-946
• /
• 1989

본 연구에서는 CT시험편을 이용하여 소규모 항복조건하에서 하한계(near threshold)영역과 안전균열성장(제II)영역의 균열진전거동을 파악하고 피로균열 진전속도와 음향방출거동, 파단면 특성을 각각 비교, 고찰하여 각 파라미터간의 상관 관계 및 유용성을 검토하고자 한다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 춘계학술대회 논문집
• /
• pp.174-180
• /
• 1995