• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권1호
• /
• pp.128-134
• /
• 2012

This paper gives an overview of the requirements for electrical equipment in potentially explosive atmospheres and describes how these are applied to electrical machines and drives in hazardous areas. The method by which equipment can be shown to be safe in a whole range of gases, by testing in a single test gas, is covered. It is shown how the more recently introduced methods of protection for hazardous areas, increased safety and nonsparking, are ideally suited to AC machines and drives. A novel method of measuring the fullload temperature rise of electrical machines for hazardous, and other areas, without the need to connect a mechanical load to the machine's drive shaft is explained.

• Journal of Power Electronics
• /
• 제9권3호
• /
• pp.343-353
• /
• 2009

In this paper, a nonlinear controller is proposed for Doubly-Fed Induction Machine (DFIM) drives. The nonlinear controller is designed based on an adaptive backstepping control technique, using a fifth order model of an induction machine in the synchronous d & q axis rotating reference frame, whose d axis coincides with the space voltage vector of the main AC supply, and using the rotor current and stator flux components as state variables. The nonlinear controller can perfectly track the torque reference signal measured in the stator terminals under the condition of unity power factor regulation, in spite of the stator and rotor resistance variations. In order to make the drive system capable of operating in the motoring and generating modes below and above the synchronous speed, two level Space-Vector PWM (SV-PWM) back-to-back voltage source inverters are employed in the rotor circuit. It is confirmed through computer simulation results that the proposed control approach is effective and valid.

• 전력전자학회논문지
• /
• 제7권3호
• /
• pp.244-252
• /
• 2002

본 논문에서는 가변속 교류 전동기 구동에 많이 사용되는 3상 ac/dc/ac PWM 컨버터 시스템에서의 직류링크 리플전류를 주파수 영역에서 해석하고자 한다. 고조파 전류는 컨버터의 스위칭함수와 지수함수 형태의 퓨리에 급수 전개를 이용하여 분석된다. 전원측 컨버터와 부하측 인버터의 스위칭 주기간의 변위각과 비동기 PW이 리플전류에 미치는 영향도 고찰된다. 해석 결과가 PSIM을 이용한 시뮬레이션으로부터 나온 고조파 스펙트럼과 잘 일치함을 확인한다 제시된 해석기법은 PWM의 원리에 대한 이해를 돕고, 해석 결과는 직류링크 커패시터의 고주파 등가 모델링에 이용된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 추계학술대회 논문집 학회본부
• /
• pp.264-267
• /
• 1989

In the vector controlled induction machine drives, mechanical speed sensors such as shaft encoder and resolver have been used. However, the mechanical speed sensors present some problems and restrict the wide applications of high performance AC drives. This paper describes the vector control strategy with the speed estimation algorithm in which motor slip frequency is calculated. Also, the angle deviation of the rotor flux vector is calculated and instaneously compensated to keep the q axis flux zero in the rotationary reference frame.

• 유공압시스템학회논문집
• /
• 제5권4호
• /
• pp.26-31
• /
• 2008

This paper deals with the issue of position tracking control of a clamp-cylinder for injection moulding machine with electric-hydrostatic drives. A fixed displacement pump is utilized in combination with AC motor in order to directly control a clamp-cylinder. A clamp-cylinder may be required to operate under a variety of operating conditions. Therefore, robust control performance is important in position tracking control applications. In order to accommodate mismatches between the real plant and the model used for controller design, discrete-time sliding mode control is developed by combining a velocity feedforward loop. From tracking control experiments, it is shown that significant reduction in position tracking error is achieved through the use of sliding mode control.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.39-42
• /
• 1994

The application of speed or position control technique in AC drives demands accurate position and velocity feedback information. Generally, resolver and absolute encoders are used as a velocity or position sensor. But they increase cost and when the sampling frequency is faster than sensoer's output frequency we can't Set exact information. In order to solve this problem this thesis proposes a speed and a position observer design for Permanent-Magnet Synchronous Motors(PMSM) specialty in low speed drives. Most literatures on this topic design the observer based on the field_oriented d_q model. But in this thesis, a new approach to machine dynamics is proposed. Since it is difficult to design the observer using the nonlinear model, the machine model is here linearlized at the operating point. The observer designed is implemented by software using Intel's 8097 microprocessor and verifies the proper performance of observer by simulation and experiment.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권3호
• /
• pp.109-114
• /
• 2002

This paper analysis the transient performance of the modified excitation system using 4-quadrant chopper for a synchronous machine connected to HVDC system. Conventionally, capacitors are used to supply reactive power requirement at a strong converter bus. And the installation of a synchronous machine is essential in an isolated weak network to re-start after a shutdown of HVDC and to increase the system strength. However, a conventional static excitation system has some problems which are harmonic instability and the system stress due to overvoltage. To reduce these problems, the new excitation system, which has 4-quadrant chopper, is proposed. As the proposed system provides the capability to allow reverse current and isolate between AC network and excitation power, problems of overvoltage and harmonic instability can be solved. The investigation is performed and confirmed by the time domain digital simulation using PSCAD/EMTDC program.

• Journal of Power Electronics
• /
• 제10권5호
• /
• pp.468-476
• /
• 2010

This paper proposes and develops a new direct voltage control (DVC) approach. This method is designed to be applied in various applications for AC drives fed with a three-phase voltage source inverter (VSI) working with a constant switching time interval as in the standard direct torque control (DTC) scheme. Based on a very strong min(max) criterion dedicated to selecting the inverter voltage vector, the developed DVC scheme allows the generation of accurate voltage forms of waves. The DVC algorithm is implemented on a dSPACE DS1104 controller board and then compared with the space vector pulse width modulation technique (SVPWM) in an open loop AC drive circuit. To demonstrate the efficiency of the developed algorithm in real time and in closed loop AC drive applications, a scalar control scheme for induction motors is successfully implemented and experimentally studied. Practical results prove the excellent performance of the proposed control approach.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1211-1214
• /
• 1992

본 논문에서 제안한 Fara DS Series의 AC SERVO (DC BRUSHLESS) MOTOR 제어기는 ROBOT, CNC, 각종 공작기계및 FA기기에서 MOTOR를 구동 원으로 사용하는데 사용되는 제품이다. AC SERVO MOTOR DRIVE의 Inverter에 IGBT(Insulated Gate Bipoler Transistor)를 사용하여 Switching 주파수를 높임으로써 Motor를 가변속 제어할때 발생하는 소음 및 진동을 극소화 하였다. 또한 일반적으로 Motor 속도제어를 급감속으로 제어할때 Servo Motor의 비선형 특성으로 인한 전류위상을 보상하여 모든 동작구간에서 최적의 상태의 제어가 되도록 개발하였다. 그리고 다양한 User Option 기능을 내장하여 User가 원하는 제어대상에 효과적으로 적용할 수 있도록 하였다. 아울러 MOTOR 제어기에 내장 된 다수의 보호기능을 통해서 Motor운전중 발생하는 이상상태에 대해 제어기를 보호할 수 있도록 하였다. 제안한 제어기는 부하변동, 전압변동, 온습도변동에 대해 속도변동율을 최소화 함으로써 ROBOT, CNC등 FA분야에서 폭넓게 이용할수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 추계학술대회 논문집 학회본부
• /
• pp.326-331
• /
• 1990

In the vector-controlled induction machine drive, mechanical sensors restrict the wide applications of high performance AC drives. So in resent years, many papers have been presented which doesn't need mechanical sensors, named by sensorless vector control. But sensorless control has a few serious problem, one of which Is poor speed estimation in case of incorrect rotor resistance (Rr) information. This paper describes the stator flux orientation speed control strategy with the speed estimation algorithm. and the method of adapting Rr change due to thermal heating. By proposed method. We can acquire precise speed estimation and higher performance.