• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2018년도 전력전자학술대회
• /
• pp.450-451
• /
• 2018

본 논문에서는 전기자동차의 1회 충전 주행거리 연장 및 연비 향상을 위하여 주요 운전 영역에서의 평균효율을 극대화 시킬 수 있는 다단 변속 회로를 제안하였다. 제안한 회로는 Thyristor를 이용한 직 병렬 변속회로로 구성되어 있다. Thyristor의 특성으로 인해 과도상태가 없고 끊김없는 변속이 가능하여 추가적인 스너버 회로가 필요 없으며, 낮은 스위치 손실로 인해 전기자동차 구동 시스템의 고효율 및 저가격을 기대할 수 있다. 제안한 다단 변속 시스템의 타당성을 검증하기 위하여 80kW급 변속회로 AC 전동기와 연계하여 변속 동작을 검증하였다.

• 대한수의학회지
• /
• 제39권6호
• /
• pp.1066-1072
• /
• 1999

The present study was carried out to investigate the blood markers of Cheju horses. The red cell types (blood groups) were tested from 73 Cheju native horses and 118 Cheju racehorses by serological procedures with 23 reagents. The blood group phenotypes observed with high frequency were Pb(34.3%), Qc(56.2%), Qb(15.1%) and genotypes Dbcm/dghm(12.3%), Dde/dghm(9.6%), Dad/bcm(6.8%), Dcgm/de(6.8%) in Cheju native horses, while Aa(63.6%), Pa(44.9%), P-(28.8%), Qabc(36.4%), Dbcm/cgm(14.4%), Dbcm/bcm(10.2%), Dbcm/de(7.6%), Dbcm/dghm(5.1%), Dde/dk(5.1%) in Cheju racehorses. Alleles observed with high frequency were Ab(0.128), Ac(0.169), Dad(0.103), Dadn(0.075), Ddghm(0.226), Pb(0.316), Qc(0.494) in Cheju native horses and Aa(0.529), Dbcm(0.306), P-(0.531), Qabc(0.197), Q-(0.504) in Cheju racehorses. No specific variation of blood groups and allele frequencies of C,K,U system were observed in Cheju native horses and Cheju racehorses. The mean heterozygosity in Cheju native horses and Cheju racehorses was observed 0.5344 and 0.5102, respectively.

• Journal of Power Electronics
• /
• 제16권6호
• /
• pp.2173-2181
• /
• 2016

Permanent magnet synchronous motors (PMSMs) have higher torque and superior output power per volume than other types of AC motors. They are commonly used for applications that require a large output power and a wide range of speed. For precise control of PMSMs, knowing the accurate position of the rotor is essential, and normally position sensors such as a resolver or an encoder are employed. On the other hand, the position sensors make the driving system expensive and unstable if the attached sensor malfunctions. Therefore, sensorless algorithms are widely researched nowadays, to reduce the cost and cope with sensor failure. This paper proposes a sensorless algorithm that can be applied to a wide range of speed. The proposed method features a robust operation at low-speed as well as high-speed ranges by employing a gain adjustment scheme and intermittent voltage pulse injection method. In the proposed scheme the position estimation gain is tuned by a closed loop manner to have stable operation in tough driving environment. The proposed algorithm is fully verified by various experiments done with a 1 kW outer rotor-type PMSM.

• 조명전기설비학회논문지
• /
• 제27권5호
• /
• pp.95-103
• /
• 2013

Protection of the electrical and electronic equipment against surges in low voltage AC power distribution systems is based on wide applications of surge protective devices(SPDs). Cascade application of SPDs located at the service entrance of a building and near sensitive equipment is intended to ensure the optimal voltage protection level and energy sharing among cascade SPDs. In this paper, when surges impinge at the service entrance of the building of interest, the protection characteristics of two-stage cascade SPD systems were investigated. The influence of the distance between the upstream and downstream SPDs on the voltage protection level and energy sharing of the two-stage cascade SPD systems were analyzed experimentally. It was found that the energy sharing of two-stage cascade SPD systems strongly depends on the distance between the two SPDs and the component of SPD. As the distance between the two SPDs increases, the energy absorbed by the upstream SPD increases while the energy absorbed by the downstream SPD decreases. Consequently, it is desirable to select the upstream and downstream SPDs having the proper energy capability with due consideration of the distance between the two SPDs.

• 한국전기전자재료학회논문지
• /
• 제31권7호
• /
• pp.496-501
• /
• 2018

In this study, we prepared 40, 45, 50, 55, 60, 65, and 70 wt% content composites filled in epoxy matrix for two micro silica and three micro alumina types for use as a GIS heavy electric machine. As a filler type of epoxy composite, micro silica composites showed excellent AC breakdown strength properties compared to micro alumina composites in the case of electrical properties of micro silica and alumina. The electrical breakdown properties of micro silica composites increased with increasing filler content, whereas those of micro alumina decreased with increasing filler content. In the case of mechanical properties, the micro silica composite showed improved tensile strength and flexural strength compared with the micro alumina composite. In addition, mechanical properties such as tensile strength and flexural strength of micro silica and alumina composites decreased with increasing filler content. This is probably because O-H groups are present on the surface of silica in the case of micro silica but are not present on the surface of alumina in the case of micro alumina.

• Journal of Power Electronics
• /
• 제16권3호
• /
• pp.1076-1086
• /
• 2016

PI controllers are one of the most widely used controllers in industrial control systems due to their simple algorithms and stability. The parameters K_p and K_i determine the performance of the system response. The response is expected to improve by increasing the gain of the PI controller. However, too large a gain will accelerate the speed response and cause vibrations, which is not what is expected. This paper proposes a way to suppress vibrations by detecting the vibration frequency and extracting the vibration signal as a compensation to the speed feedback. Additionally, in order to improve its disturbance rejection ability, a low-order disturbance observer is proposed. This paper also explains the operation principle of the proposed method by analyzing the transfer function and it describes the design of the controller parameters in detail. Simulation and experimental results are provided to verify the merits of the proposed method. These results also show the good performance of the proposed method. It has a rapid response and suppresses vibrations.

• 한국전기전자재료학회논문지
• /
• 제21권2호
• /
• pp.182-187
• /
• 2008

This paper dealt with the detection algorithm of series arcing, which is a cause of electric fires in low-voltage wiring systems. To find the distinguished electrical features of series arc, we simulated series arcing by the arc generator specified in UL1699. An electric heater, an inverter-controlled vacuum cleaner, and a phase-controlled incandescent lamp were used as loads to generate series arcing. A high-pass filter (HPF) with the low cut-off frequency of 3 kHz at -3 dB was fabricated and applied to separate the series arc signal from the AC voltage source. The experiment showed that the high frequency signal generates randomly during series arcing, and the phase-controlled incandescent lamp produces high frequency pulses even in normal state. In this case, the magnitude, the width, and the randomness of high frequency signal should be analyzed to estimate series arcing precisely.

• 한국초전도ㆍ저온공학회논문지
• /
• 제13권2호
• /
• pp.9-12
• /
• 2011

Superconducting motor has a lot of benefits from high power density for ship propulsions, so a number of research project are in progress worldwide. Despite of all the benefits, there is always a difficulty of cryo-moving part for conventional air-core superconducting synchronous motors. In order to get rid of this moving cryogenic part, we propose a homopolar superconducting synchronous motor, which has high temperature superconducting armature and field coils. The rotor is supposed to be made of iron only and excited by the stationary HTS field coils. The stationary field coils make the cooling system simple and easy to realize because there is no cryo-moving part. A design result of a 10 hp homopolar synchronous motor is presented in this paper. The self and mutual inductance of the motor having the size of air gap as variable parameter are calculated by a 3-dimemsional finite element method. The value of design variables such as the dimension of a motor and the number of turns, etc. is decided by performing the coordinate transformation of the calculated inductance. The operating frequency is supposed to be below 5 Hz for low rotating speed which is needed for a purpose of ship propulsion. Low frequency also has the benefit of low AC losses.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.49-54
• /
• 2010

An integrated machining center is developed for high precision and productivity manufacturing. The developed machine is composed of the high precision spindle using ball bearings, the high stiffness bed and the three axis CNC controller with the high resolution AC servo motor. In this paper, structural and modal analysis for the developed machine are carried out to check the design criteria of machine. The analysis is carried out by FEM simulation with using the commercial software, CATIA V5, ANSYS and ARMD. The simulation model of machine is made by shell and solid finite elements. This study also presents the measurement system on the modal analysis of an integrated machining center. The weak part of the machine is found by the analytical evaluation. The results provide with the structural modification data for good dynamic behaviors. And the safety of machine is confirmed by the modal analysis of modified machine design. As this study results can be trustworthy with the analysis of ANSYS and CATIA, integrated machining center can be successfully developed.

• 한국전기전자재료학회논문지
• /
• 제19권6호
• /
• pp.574-578
• /
• 2006

Toward the practical applications, on operation of conduction-cooled HTS SMES at temperatures well below 77 K should be investigated, in order to take advantage of a greater critical current density of HTS and considerably reduce the size and weight of the system. Recently, research and development concerning application of the conduction-cooled HTS SMES that is easily movement are actively progressing in Korea. Electrical insulation under cryogenic temperature is a key and an important element in the application of this apparatus. Using multi wrapped copper by Polyimide film for HTS SMES, the breakdown characteristics of models for turn-to-turn, that is surface contact model, were investigated under ac and impulse voltage at 77 K. A material that is Polyimide film (Kapton) 0.025 mm thickness is used for multi wrapping of the electrode. Statistical analysis of the results using Weibull distribution to examine the wrapping number effects on breakdown voltage under at and impulse voltage in $LN_2$ was carried.