• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.548-552
• /
• 2003

In the braking system, the friction force is the most important factor of the design. For long time, many researchers have been strived for getting the exact friction coefficients. But the friction coefficients are affected by the road condition and changed by lots of parameters, such as normal force and characteristics between two contacted materials, temperature, etc. For the development of ABS of the aircraft, HILS(Hardware-In-the-Loop-Simulation) test and dynamometer test was carried out. For the calculation of the friction coefficients, the wheel moments were measured using the load cell mounted on the housing of the wheel. The test conditions were dry and greasy, as the 0.7 and 0.4 in friction coefficient, respectively. In this paper, the test results of the friction coefficients were represented and the improvement method was suggested.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.517-523
• /
• 2004

Recently, wheel slip controllers with controlling the wheel slip directly has been studied using the brake-by-wire actuator. The wheel slip controller is able to control the braking force more accurately and can be adapted to various different vehicles more easily than the conventional ABS systems. The wheel slip controller requires the information about the tire braking force and road condition in order to achieve the control performance. In this paper, the tire braking forces are estimated considering the variation of the friction between brake pad and disk due to aging of the brake, moisture on the contact area or heating. In addition, the road friction coefficient is estimated without using tire models. The estimated performance of tire braking forces and the road friction coefficient is evaluated in simulations.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.211-217
• /
• 2007

The wheel slip control systems are able to control the braking force more accurately and can be adapted to different vehicles more easily than conventional ABS (Anti-lock Brake System) systems. In realizing the wheel slip control systems, real-time information such as the tire braking force at each wheel is required. In addition, the optimal target slip values need to be determined depending on the braking objectives such as minimum braking distance and stability enhancement. In this paper, a robust wheel slip controller is developed based on the adaptive sliding mode control method and an optimal target slip assignment algorithm is proposed for maximizing the braking force. An adaptive law is formulated to estimate the braking force in real-time. The wheel slip controller is designed based on the Lyapunov stability theory considering the error bounds in estimating the braking force and the brake disk-pad friction coefficient. The target slip assignment algorithm searches for the optimal target slip value based on the estimated braking force. The performance of the proposed wheel slip control system is verified in HILS (Hardware-In-the-Loop Simulator) experiments and demonstrates the effectiveness of the wheel slip control in various road conditions.

• ICROS
• /
• v.2 no.1
• /
• pp.18-24
• /
• 1996

본 연구에서는 향후 초소형, 초저가의 ABS가 개발되어 보편적으로 차량에 장착될 것을 대비해 독자적으로 설계, 제작된 ABS에 대해 제시하고자 한다. 개발의 목표는 유압 모듈레이터의 핵심 부품인 솔레노이드 밸브의 개발과 장착성이 우수한 소형의 PCB(Printed Circuit Board)형의 ECU(Electronic Control Unit)이다. 특히 개발된 밸브의 경우 현재 범용적으로 많이 사용되는 2포지션 2웨이 밸브가 아닌 2포지션 3웨이 밸브이며, 이로써 1채널당 브레이크 라인 압력을 제어하기 위해 1개의 밸브만 소요된다.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.241-246
• /
• 1998

It is well known for 410L ferritic stainless steel powder to applicate a sensor ring in anti-lock brake system of automobile, several studies, because of its excellent magnetic properties. This study was carried out to investigate the magnetic properties such as the maximum magnetic induction, coercivity and maximum permeability of the materials with functions of sintering density, time and temperature, and concluded as follows: 1. Sintering under the circumstances of Ar gas and the temperature of $1250^{\circ}C$ for 60min, showed that nitrogen was increased, whereas carbon and oxygen decreased in quantities. 2. Both maximum magnetic induction value of 4700Gauss and permeability of 200 were obtained at the maximum sintering density of $6.89g/cm^2$. Here, the properties showed a linear increasement with increasing the sintering density. 3. Coercivity sharply decreased with incresing the sintering density and reached to 7.6Oe at the maximum sintering density of $6.89g/cm^2$.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.519-524
• /
• 2004

This study is concerned with the braking distance estimation using frictional energy rate. First, steady state rolling analysis is performed, and using this result, the braking distance is estimated. Dynamic rolling analysis during entire braking time period is impratical, so that this study divides the vehicle velocity by 10km/h to reduce the analysis time. The multiplication of the slip rate and the shear stress provides the frictional energy rate. Using frictional energy rate, total braking distance is estimated, In addition, ABS(Anti-lock Brake System) is considered, and two type of slip ratios are compared, One is 15% slip ratio for the ABS condition, and the other is 100% slip ratio which leads lo the almost same braking distance as the elementary kinematic theory. A slip ratio is controlled by angular velocity in ABAQUS/Explicit, A 15% slip ratio gives the real vehicle's braking distance when the frictional energy occurred al disk pad is included. Disk pad's frictional energy rate is calculated by the theoretical approach.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.72-80
• /
• 2013

This study is to develop and evaluate an AFS and an ARS controllers to enhance lateral stability of a vehicle. A sliding mode control (SMC) and a fuzzy logic control (FLC) methods are applied to calculate the desired additional steering angle of AFS equipped vehicle or desired rear steer angle of ARS equipped vehicle. To validate AFS and ARS systems, an eight degree of freedom, nonlinear vehicle model and an ABS controllers are also used. Several road conditions are used to test the performances. The results showed that the yaw rate of the AFS and the ARS vehicle followed the reference yaw rate very well within the adhesion limit. However, the AFS improves the lateral stability near the limit compared with the ARS. Because the SMC and the FLC show similar vehicle responses, performance discrimination is small. On split-${\mu}$ road, the AFS and the ARS vehicle had enhanced the lateral stability.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.1-13
• /
• 2002

최근 자동차가 편리성과 안전성을 추구함에 따라서 자동차 부품도 과거의 기계식 동작 방법에서 전자 제어 장치가 부착된 전자식 동작 방법으로 발전되어 가고 있는 추세입니다. 또한 연비 향상을 위하여 부품의 소형화가 급속히 추진되고 있습니다. 이러한 전자화, 소형화를 실현시키기 위해 자동차 부품에서의 정밀성이 요구되어 지고 있고, 부품 제조 측면에서는 고속화, 정확성이 요구되고 있는 실정입니다. 당사의 경우 CBS (Conventional Brake System)를 생산하다가 전자 제어 장치가 부착된 ABS (Anti-lock Brake System)의 생산을 시작할 때, 부품의 정밀도를 좌우하는 각 치수의 공차 영역이 전체적으로 CBS 대비 약 1/5 수준밖에 되지 않고, 가공 속도는 약 2 배가 빨라야 하기 때문에 생산 준비 단계에서 많은 시행 착오를 겪어야만 했습니다. 여기서 당사가 ABS를 양산하면서 겪은 경험을 토대로 기술토록 하겠습니다. 가공 기술의 경우 고속, 정밀 가공을 실현시키기 위해서 크게 4 가지 측면을 고려해야만 하며, 그 4가지는 설비, Tool Holder, Tool, Chip 측면입니다. 먼저 설비가 고정도가 되기 위해 고강성을 필요로 하는 것은 물론 가동중에 필연적으로 발생하는 열변형에 대한 대책을 수립하지 않으면 안됩니다. 이러한 열변형은 설비 설계 단계에서 대책을 수립할 수 있는 것도 있지만 주위 온도 변화에 의한 열변형처럼 사용 중에 발생되는 것은 설비 사용자가 장시간에 걸친 Data 를 확보하여 대책을 수립하지 않으면 안됩니다. 또한 Tool Holder의 정도도 일반적으로 사용하는 것보다는 고정도의 것이 요구되어지므로 Tool Holder Maker 에 반드시 요구 정도를 명기하여 주문하여야 합니다. Tool도 고속화를 실현시키기 위해 고정도의 다이아몬드 공구가 필요하였고 이를 국내에서 개발하기 위해 많은 시행 착오를 겪어야만 했습니다. 또한 Chip 배출이 고정도의 필수 고려 항목으로서 당사에서는 경우에 따라 여러 가지의 방법을 사용하고 있습니다. 조립 기술의 경우 스테인레스 박판을 열변형을 최소로 하면서 용접을 하기 위해서 레이저 용접을 도입하였고, 부품을 압입하면서 정확하고 정밀한 치수 셋팅을 위하여 서버 모타를 이용한 압입 방법을 사용하였습니다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.12-18
• /
• 2009

Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this study, in order to estimate the speed at the brake onset, rapid braking tests were executed on the proving ground. We compared with a skid length and wheel locking time of an expert driver and a general person. We verified that the skid mark of expert driver occurs longer than general person's. A new method is proposed to determine the speed of a vehicle at the brake onset of maximum braking, which could be applied to a reconstruction of vehicle with Non-ABS.

• International Journal of Automotive Technology
• /
• v.3 no.4
• /
• pp.147-155
• /
• 2002

Mechatronic subsystems are more and more developed in automotive industries. To enhance the local controls performances, a cooperative control between ABS and Suspension systems is proposed. The respective controls are first designed separately with their dedicated models. Then a hybrid hierarchical architecture is developed. The advantage of this architecture is discussed through vehicle performance with simulation results.