• Journal of Advanced Navigation Technology
• /
• v.24 no.4
• /
• pp.245-250
• /
• 2020

Currently, unmanned military vehicles under development in Korea have more devices to carry out various missions, and interface cables between them are also increasing. In addition, due to a small space problem inside the unmanned vehicle, devices are required to be miniaturized and integrated. For two reasons, connectors also need to be selected, which makes them vulnerable to noise due to the closer distance between the pins. In this paper, we analyzed how much the magnetic field produced by noise at the connector pin where cable twist is released affects the surrounding pin and presented the guide for optimal pin placement. First, the effect of magnetic field is greater than the crosstalk between pin and pin. Second, the magnetic field on both sides between + and - is strong when approaching one step with noise source. Third, the magnetic field strength is improved when setting the ground pin as the ground pin between the noise and the original signal when approaching the A noise source and the two steps. Fourth, in the case of a differential mode communication, the optimal placement area of the sensitive signal was presented according to positions Tx± and Rx±.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.188-189
• /
• 2013

본 연구에서는 군 항공용 레이더의 프로세서 유닛에 적용하기 위하여 $115/200VAC{\pm}10%$, 3상, 400Hz 및 +28VDC 입력, 최대 출력전력 488.5W, 효율 82%이상(@70%부하), 출력 전원 8개의 다중 출력 스위칭 전원공급기를 개발하였다. 개발 목표 효율인 82% 이상을 달성하기 위해 전력이 큰 3개의 출력에(+3.3V/55A, +5V/32A, +12V/10A) 대해 동기정류 하프브릿지 방식을, 나머지 소전력 출력은 다중 출력 플라이백 방식을 적용하여 설계 및 제작하였고, 시험 결과 70% 부하에서 83.3%의 우수한 효율 특성을 확인하였다. 또한, 군용 장비로써의 전자기 간섭 및 환경조건 만족 여부 확인을 위해 군사규격에 따라 신뢰성 시험을 수행하여 개발된 전원공급기의 신뢰성을 확인하였다.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.20 no.3
• /
• pp.35-43
• /
• 2012

Medium size rotorcraft consist of approximately 5,000 key components. The components must satisfy the target weight and performance requirement through optimization. Therefore a rotorcraft component has approximately 100 times higher unit cost for mass production than the equivalent of an automobile's, along with huge development cost. Configuration management consists of four main parts : configuration identification, configuration control, configuration audit, and data management. In development programme, configuration management is one of the methods to save development cost, and setting a well-structured configuration management system according to the Military Standard is an important factor in success of the programme. The paper proposes a configuration management system suitable for development of various multi-use components development and presents that the configuration management was performed successfully during dual-use component development programme using the established system.

• The Journal of Asian Finance, Economics and Business
• /
• v.9 no.5
• /
• pp.177-186
• /
• 2022

This study aimed to measure the impact of societal participation of Saudi banks on customer satisfaction and determine the statistical differences in customer satisfaction according to sex, age, income, education, and work type. Societal participation has economic and environmental dimensions. The study population includes all Saudis in the government, military, and private sectors reaching 3.58 million in 2021. The unit of analysis is Saudi customers of commercial banks. The 12 banks have societal programs. The research tool is a "Questionnaire," It is distributed face-to-face at places of work. The study concludes that economic participation has no impact on customer satisfaction; however, the impact of environmental participation on customer satisfaction is proved. The study shows no statistical differences in customer satisfaction according to mediators (sex, age, income, education, and work type). Despite the environmental participation being the tangible product by Saudi banks in the local market, the study concludes the positive relationship between societal participation and customer satisfaction. The study presents a set of recommendations for enhancing societal participation in the Saudi businesses environment.

• Journal of architectural history
• /
• v.18 no.1
• /
• pp.91-111
• /
• 2009

The purpose of this study is to analyze paejang system of the castle constructions In the late period of Chosun dynasty. Moreover, this study aimed to examine effects and influences of its constructional productivity. The results are as follow; 1. Paejang was originally a sort of military positions. Thereafter it had been adopted to the various fields like soonrapaes. Pae, which was a regular working unit organized with $30{\sim}50$ laborers, took charge of the works allocated with its own chargeable section. 2. The first adoption of paejang system was found at the construction of Ganghwa-oyseong in 1690. Since the period of King Yeongjo and Jeongjo, it was generally used as a working system. 3. Yoo Hyeongwon had early suggested that this system should be adopted as a reformative system because it had a perfect command system like Soko-je, the provincial military system. 4. At the constructions of Dongnae-upseong, Jeonjoo-upseong and Daegoo-upseong in the period of King Yeongjo, paes were organized to $40{\sim}60$units, and worked in the fields of masonry, carnage and picking of stones. 5. At the construction of Soowon-seong in the period of King Jeongjo, a large number of various paejangs participated in all of working fields. Especially masonry-paes were usually organized with over 100 units. 6. It was estimated that paejang system surely could guarantee saving labors and term of works. Moreover, it was a basis for the further development form of dogup-je, a contracted work system. 7. Paejang system was applied in the constructions of Buddhist temples since the middle period of 1700s and later, it was widely used in the constructions of palaces.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.5
• /
• pp.649-657
• /
• 2018

It is essential that weapons which are mounted on aircraft need to prove its reliability and safety during its developments. A guided missile should have high reliability and safety throughout various tests which are including ground tests, captive flight tests, detailed technical tests and operational tests. In these various tests, it is vital that software of each component in the guided missile should be easily updated in order to correct algorithms or errors. In this paper, we propose a software update technique based on MDTP(mass data transfer protocol) which are defined in MIL-STD-1760. The proposed techniques have the following advantages: First, software of each unit in a weapon can be updated through a test equipment without disassemble a guided missile. Second, development periods for a software update can be reduced by reusing MDTP. Third, we can easily maintenance of the software because it is based on standard. We proved its efficiency and validity through experiments. Therefore, the proposed technique should be effectively utilized for software update of a weapon mounted on an aircraft during development processes.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.3
• /
• pp.294-301
• /
• 2020

Man-In-Simulant Test(MIST) provides a test method to evaluate chemical protective equipments such as protective garments, gloves, footwear and gas mask. The MIST chamber is built to control concentration of chemical vapor that has a activity space for two persons. Non-toxic methyl-salicylate(MeS) is used to simulate chemical agent vapor. We carried out to measure inward leakage MeS vapors by using passive adsorbent dosimeter(PAD) which are placed on the skin at specific locations of the body while man is activity according to the standard procedure in MIST chamber. But more time is required for PADs and there is concern of contamination in PADs by recovering after experiment. Therefore detector for measuring in real time is necessary. In order to analyze in real time the contamination of the personal protective equipment inside the chemical environment, we have developed a wireless real-time gas detector. The detector consists of 8 gas-sensors and 1 control-board. The control-board includes a CPU for processing a signal, a power supply unit for biasing the sensor and Bluetooth-chipset for transmission of signals to external PC. All signals from gas-sensors are converted into digital signals simultaneously in the control-board. These digital signals are stored in external PC via Bluetooth wireless communication. The experiment is performed by using protective equipment worn on manikin. The detector is mounted inside protective equipment which is capable of providing a real-time monitoring inward leakage MeS vapor. Developed detector is demonstrated the feasibility as real-time detector for MIST.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.1
• /
• pp.33-40
• /
• 2022

With the recent increase in the development of military drones, they are adopted and used as the combat system of battalion level or higher. However, it is difficult to use drones that can be used in battles below the platoon level due to the current conditions for the formation of units in the Korean military. In this paper, therefore, we developed a program drones equipped with a thermal imaging camera and LiDAR sensor for reconnaissance and exploration that can be applied in battles below the platoon level. Using these drones, we studied the possibility and feasibility of drones for small-scale combats that can find hidden enemies, search for an appropriate detour through image processing and conduct reconnaissance and search for battlefields, hiding and cover-up through image processing. In addition to the purpose of using the proposed drone to search for an enemies lying in ambush in the battlefield, it can be used as a function to check the optimal movement path when a combat unit is moving, or as a function to check the optimal place for cover-up or hiding. In particular, it is possible to check another route other than the route recommended by the program because the features of the terrain can be checked from various viewpoints through 3D modeling. We verified the possiblity of flying by designing and assembling in a form of adding LiDAR and thermal imaging camera module to a drone assembled based on racing drone parts, which are open source hardware, and developed autonomous flight and search functions which can be used even by non-professional drone operators based on open source software, and then installed them to verify their feasibility.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.1
• /
• pp.47-60
• /
• 2018

In this paper, we proposed a method for eliminating aiming error of unguided anti-tank rocket using improved target tracking. Since predicted fire is necessary to hit moving targets with unguided rockets, a method was proposed to estimate the position and velocity of target using fire control system. However, such a method has a problem that the hit rate may be lowered due to the aiming error of the shooter. In order to solve this problem, we used an image-based target tracking method to correct error caused by the shooter. We also proposed a robust tracking method based on TLD(Tracking Learning Detection) considering characteristics of the FCS(Fire Control System) devices. To verify the performance of our proposed algorithm, we measured the target velocity using GPS and compared it with our estimation. It is proved that our method is robust to shooter's aiming error.

• Journal of the military operations research society of Korea
• /
• v.32 no.1
• /
• pp.90-112
• /
• 2006

The main purpose of this study is to develop an economical efficiency and maximize efficient characteristic of national defense supply. It's very important to select a supply unit which is excellent in business because it's maximize its efficiency in procurement. So this study focused on the users' dissatisfactions and the elements which have an effect on procurement, especially when they have a general competition contract. In order to have a good result, we studied the papers from Ministry of National Defense supply headquarters and the National Defense Quality Control Office, and referred to various data which contracted within recent 2 years and collect users' dissatisfactions in 3 years in track and mobile equipment field. And we present a analysis between the dissatisfactions and the elements of procurement method by SPSS 12.0.