• Journal of Environmental Health Sciences
• /
• v.13 no.1
• /
• pp.17-33
• /
• 1987

As a result of technical advances and industrialization, the characteristics of domestic and industrial wastes are becoming more complex. Accordingly, improved treatment and disposal systems are being continuously sought to take account of complex characteristics and to comply with economic restrictions. In this study, an application of pyrolysis to the treatment of industrial wastes, including waste scrap rubber, waste raw material used in making the slipper bottom and waste PVC pipe, and the effectiveness of pyrolysis in resource recovery from these wastes were investigated. Batches of wastes were pyrolysed by external heating to a temperature of 400-800$\circ$C in a 32 mm diameter x 0.9 m long silica tube to produce combustible gases, oils and chars. Before the start of pyrolysis runs, the entire system was purged with nitrogen gas to exclude the air. The temperature inside the retort was controlled by the thermocouple in the gas stream, and referred to as the pyrolysis temperature. Under these conditions three products were separately collected and further analyzed. The results were summarized as follows. 1. More gases and less chars were produced with higher pyrolyzing temperature and with higher rates of heating, but the yields of oils tended downwards at temperatures above 700$\circ$C. Accordingly, operating conditions of pyrolysis should be varied with desired material. 2. Calorific values and sulfur contents of produced oils were sufficient and suitable for fuel use. Chars from waste rubber had high heating values with low sulfur contents, but calorific values of chars from waste PVC and waste slipper were as low as 3, 065-4, 273 kcal/kg and 942-2, 545 kcal/kg, respectively. Therefore, char from these wastes are inappropriate for fuel. 3. Soluble contents of Pb, Cd, Cu and Zn in chars from waste rubber and waste slipper were below the Specific Hazardous Waste Treatment Standards. However soluble contents of Pb and Cd in chars from waste PVC were one or two times and five or seven times exceedingly the Specific Hazardous Waste Treatment Standards, respectively. 4. Post high heating is desirable for treatment method of waste PVC which generates toxic hydrogen chloride. 5. The proportions of hydrogen, methane and ethane in produced gases were in the range of 3.99-35.61% V/V, 18.22-32.50% V/V and 5.17-5.87% V/V, respectively. 6. Pyrolysis is a useful disposal method in case of waste slipper, which was hardly combustible, and thus investigations of this kind of materials are required for effective management of industrial waste. 7. Based upon the possible market development for products, overall pyroly economics to take account of treatment values of noncombustible or hazardous materials should be evaluated.

• Journal of Ginseng Research
• /
• v.24 no.4
• /
• pp.188-195
• /
• 2000

Using Ginseng saponins (crude saponin and total saponin) and ginsenoside Rbl Rb2, Rc, Rd, Re, Rhl, and Rh2 in this study, we have examined the effects of the compounds on the induction of differentiation in normal rat mammary epithelial cells and 7,12-dimethylbenz[a]anthracene (DMBA)-induced mammary tumor cells in culture. When normal rat mammary organoids were cultured in 100-mm culture plates in the presence or absence of ginseng saponins, there were four different cell colonies after two weeks in culture: cobble stone, spindle, honey comb, and senescence type colonies. Ginseng saponins showed different effects on the development of each colonies. Scrape-loading dye transfer tech-nique was performed to measure the effects of total saponin, Rhl, and Rh2 on intercellular junctional communication. Intercellular communication was not observed at short cultilral time, e.g., four or seven days, but when it cultured it up to two weeks, cell to cell communication was observed in saponin-treated cells. Reconstituted basement membrane, Matrigel, supported the growth and development several different multicellular structures from normal mammary organoids (e.g., ductal, webbed, stellate, and squamous colonies) or DMBA-induced mammary tumor (e.g., alveolar unit, foamy alveolar unit, squamous metaplasia, lobule-ductal, stellate, and webbed colony). In ginseng saponin-treated groups, webbed colonies were more and squamous colonies were less than control group. Moreover, the ductal colonies, marker tructure of well-differentiate mammary epithelial cells, were developed more in saponin-treated group than in control group. In conclusion, ginseng saponins affected on the differentiation of normal rat mammary epithelial cells and DMBA-induced mammary tumor cells in culture.

• Tuberculosis and Respiratory Diseases
• /
• v.66 no.3
• /
• pp.192-197
• /
• 2009

Background: Despite the benefits of home oxygen therapy in patients suffering chronic respiratory failure, previous reports in Korea revealed lower compliance to oxygen therapy and a shorter time for oxygen use than expected. However, these papers were published before oxygen therapy was covered by the national insurance system. Therefore, this study examined whether there were some changes in compliance, using time and other clinical features of home oxygen therapy after insurance coverage. Methods: This study reviewed the medical records of patients prescribed home oxygen therapy in our hospital from November 1, 2006 to September 31, 2008. The patients were interviewed either in person or by telephone to obtain information related to oxygen therapy. Results: During study period, a total 105 patients started home oxygen therapy. The mean age was 69 and 60 (57%) were male. The mean oxygen partial pressure in the arterial blood was 54.5 mmHg and oxygen saturation was 86.3%. Primary diseases that caused hypoxemia were COPD (n=64), lung cancer (n=14), Tb destroyed lung (n=12) and others. After oxygen therapy, more than 50% of patients experienced relief of their subjective dyspnea. The mean daily use of oxygen was 9.8${\pm}$7.3 hours and oxygen was not used during activity outside of their home (mean time, 5.4${\pm}$3.7 hours). Twenty four patients (36%) stopped using oxygen voluntarily 7${\pm}$4.7 months after being prescribed oxygen and showed a less severe pulmonary and right heart function. The causes of stopping were subjective symptom relief (n=11), inconvenience (n=6) and others (7). Conclusion: The prescription of home oxygen has increased since national insurance started to cover home oxygen therapy. However, the mean time for using oxygen is still shorter than expected. During activity of outside their home, patients could not use oxygen due to the absence of portable oxygen. Overall, continuous education to change the misunderstandings about oxygen therapy, more economic support from national insurance and coverage for portable oxygen are needed to extend the oxygen use time and maintain oxygen usage.

• Journal of the Korean Arthroscopy Society
• /
• v.8 no.2
• /
• pp.89-93
• /
• 2004

Purpose: To evaluate the clinical stability and function after arthroscopic anterior cruciate ligament(ACL) reconstruction using fresh-frozen tibialis tendon allograft. Materials and Methods: Of the patients who underwent ACL reconstruction using tibialis tendon allograft from July 2002 to June 2003, thirty-one patients could be evaluated and the mean follow-up period was 19 months. Evaluations included were Lysholm knee score, 2000 International knee Documentation Committee (IKDC) subjective knee score, Lachman test, pivot shift test, KT-1000 arthrometer measurement and 2000 IKDC knee examination. Results: The mean Lysholm score was 88. Twenty-eight patients (90.3%) were good or exellent for the measured parameters. Twenty-seven patients(87.1%) was over 70 in IKDC subjective knee score. Thirty patients (96.8%) had 1+ firm end or negative Lachman test. 27 patients (87.1%) had a negative pivot shift. Thirty patients (96.8%) had less than 5mm difference of maximal manual difference by KT-1000 arthrometer. Twenty -nine patients (93.5%) were nearly normal or normal grade by 2000 IKDC knee examination. Complications were 1 case of failure and 1 case of infection. Conclusion: ACL reconstruction with the double-stranded fresh-frozen tibialis tendon allograft resulted in a reliable and predictable outcome after short-term follow-up.

• Radiation Oncology Journal
• /
• v.23 no.4
• /
• pp.236-242
• /
• 2005

Purpose: To evaluate the role of surgical clips and scars in determining electron boost field for early stage breast cancer undergoing conserving surgery and postoperative radiotherapy and to provide an optimal method in drawing the boost field. Materials and Methods: Twenty patients who had $4{\sim}7$ surgical clips in the excision cavity were selected for this study. The depth informations were obtained to determine electron energy by measuring the distance from the skin to chest wall (SCD) and to the clip implanted in the most posterior area of tumor bed. Three different electron fields were outlined on a simulation film. The radiological tumor bed was determined by connecting all the clips implanted during surgery Clinical field (CF) was drawn by adding 3 cm margin around surgical scar. Surgical field (SF) was drawn by adding 2 cm margin around surgical clips and an Ideal field (IF) was outlined by adding 2 cm margin around both scar and clips. These fields were digitized into our planning system to measure the area of each separate field. The areas of the three different electron boost fields were compared. Finally, surgical clips were contoured on axial CT images and dose volume histogram was plotted to investigate 3-dimensional coverage of the clips. Results : The average depth difference between SCD and the maximal clip location was $0.7{\pm}0.55cm$. Greater difference of 5 mm or more was seen in 12 patients. The average shift between the borders of scar and clips were 1.7 1.2, 1.2, and 0.9 cm in superior, inferior, medial, and lateral directions, respectively. The area of the CF was larger than SF and IF in 6y20 patients. In 15/20 patients, the area difference between SF and if was less than 5%. One to three clips were seen outside the CF in 15/20 patients. In addition, dosimetrically inadequate coverage of clips (less than 80% of prescribed dose) were observed in 17/20 patients when CF was used as the boost field. Conclusion: The electron field determined from clinical scar underestimates the tumor bed in superior-inferior direction significantly and thereby underdosing the tissue at risk. The electron field obtained from surgical clips alone dose not cover the entire scar properly As a consequence, our technique, which combines the surgical clips and clinical scars in determining electron boost field, was proved to be effective in minimizing the geographical miss as well as normal tissue complications.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.7 no.1
• /
• pp.861-876
• /
• 1965

During my stay in the Netherlands, I have studied the following, primarily in relation to the Mokpo Yong-san project which had been studied by the NEDECO for a feasibility report. 1. Unit hydrograph at Naju There are many ways to make unit hydrograph, but I want explain here to make unit hydrograph from the- actual run of curve at Naju. A discharge curve made from one rain storm depends on rainfall intensity per houre After finriing hydrograph every two hours, we will get two-hour unit hydrograph to devide each ordinate of the two-hour hydrograph by the rainfall intensity. I have used one storm from June 24 to June 26, 1963, recording a rainfall intensity of average 9. 4 mm per hour for 12 hours. If several rain gage stations had already been established in the catchment area. above Naju prior to this storm, I could have gathered accurate data on rainfall intensity throughout the catchment area. As it was, I used I the automatic rain gage record of the Mokpo I moteorological station to determine the rainfall lntensity. In order. to develop the unit ~Ydrograph at Naju, I subtracted the basic flow from the total runoff flow. I also tried to keed the difference between the calculated discharge amount and the measured discharge less than 1O~ The discharge period. of an unit graph depends on the length of the catchment area. 2. Determination of sluice dimension Acoording to principles of design presently used in our country, a one-day storm with a frequency of 20 years must be discharged in 8 hours. These design criteria are not adequate, and several dams have washed out in the past years. The design of the spillway and sluice dimensions must be based on the maximun peak discharge flowing into the reservoir to avoid crop and structure damages. The total flow into the reservoir is the summation of flow described by the Mokpo hydrograph, the basic flow from all the catchment areas and the rainfall on the reservoir area. To calculate the amount of water discharged through the sluiceCper half hour), the average head during that interval must be known. This can be calculated from the known water level outside the sluiceCdetermined by the tide) and from an estimated water level inside the reservoir at the end of each time interval. The total amount of water discharged through the sluice can be calculated from this average head, the time interval and the cross-sectional area of' the sluice. From the inflow into the .reservoir and the outflow through the sluice gates I calculated the change in the volume of water stored in the reservoir at half-hour intervals. From the stored volume of water and the known storage capacity of the reservoir, I was able to calculate the water level in the reservoir. The Calculated water level in the reservoir must be the same as the estimated water level. Mean stand tide will be adequate to use for determining the sluice dimension because spring tide is worse case and neap tide is best condition for the I result of the calculatio 3. Tidal computation for determination of the closure curve. During the construction of a dam, whether by building up of a succession of horizontael layers or by building in from both sides, the velocity of the water flowinii through the closing gapwill increase, because of the gradual decrease in the cross sectional area of the gap. 1 calculated the . velocities in the closing gap during flood and ebb for the first mentioned method of construction until the cross-sectional area has been reduced to about 25% of the original area, the change in tidal movement within the reservoir being negligible. Up to that point, the increase of the velocity is more or less hyperbolic. During the closing of the last 25 % of the gap, less water can flow out of the reservoir. This causes a rise of the mean water level of the reservoir. The difference in hydraulic head is then no longer negligible and must be taken into account. When, during the course of construction. the submerged weir become a free weir the critical flow occurs. The critical flow is that point, during either ebb or flood, at which the velocity reaches a maximum. When the dam is raised further. the velocity decreases because of the decrease\ulcorner in the height of the water above the weir. The calculation of the currents and velocities for a stage in the closure of the final gap is done in the following manner; Using an average tide with a neglible daily quantity, I estimated the water level on the pustream side of. the dam (inner water level). I determined the current through the gap for each hour by multiplying the storage area by the increment of the rise in water level. The velocity at a given moment can be determined from the calcalated current in m3/sec, and the cross-sectional area at that moment. At the same time from the difference between inner water level and tidal level (outer water level) the velocity can be calculated with the formula $h= \frac{V^2}{2g}$ and must be equal to the velocity detertnined from the current. If there is a difference in velocity, a new estimate of the inner water level must be made and entire procedure should be repeated. When the higher water level is equal to or more than 2/3 times the difference between the lower water level and the crest of the dam, we speak of a "free weir." The flow over the weir is then dependent upon the higher water level and not on the difference between high and low water levels. When the weir is "submerged", that is, the higher water level is less than 2/3 times the difference between the lower water and the crest of the dam, the difference between the high and low levels being decisive. The free weir normally occurs first during ebb, and is due to. the fact that mean level in the estuary is higher than the mean level of . the tide in building dams with barges the maximum velocity in the closing gap may not be more than 3m/sec. As the maximum velocities are higher than this limit we must use other construction methods in closing the gap. This can be done by dump-cars from each side or by using a cable way.e or by using a cable way.

• The Korean Journal of Physiology
• /
• v.2 no.2
• /
• pp.101-135
• /
• 1968

As physical fitness measured was muscle strength (hand grips, leg extention, back lift, and arm pull and thrust), skinfold thickness (5 different sites), circulatory function (resting heart rate and blood pressure), speed (kinesiological analysis during 100m sprint, record, maximal and final speed), motor function (50 meter dash, ball throwing, standing broad jump, and pull-ups), maximal aerobic power (maximum oxygen intake by field running method), muscle power (leg and arm by inertia ergometer), and general endurance (maximum endurance running time on the treadmill at the speed of 5 MPH and grade of 15.5%) of 1131 Korean children (boys 572, girls 559) aged of 6 to 17 years, who were randomly sampled from 24 primary, middle and high schools at the two districts of Seoul and KyungKi. The results are summarized as follows: 1) The status (height and weight) of the children was almost same as that of the previously reported Korean and Japanese children of same ages. 2) Muscle strength was a gained linearly with geting age in the boys and girls but there was a little improvement in girls aged of 13 years or more. 3) The mean skin fold thickness was increased linearly with geting ages in both sexes, but the girls from 12 to 17 years of age were increased rapidly, and maximum value was 17mm, while boys was 7.0 mm. 4) In the circulatory function, the resting heart rate was decreased, but the blood pressure was increased with ages in both sexes within the normal limits. 5) The maximum and final speed during 100 meter sprint increases with age in boys but girls who are 12 years old or older, were not improved any mere. The patterns of running were same in both sexes, and maximum speed reached at about 30 meters from starting line. 6) The motor function was increased with age in both sexes, but there was no improvement in 12 years of age or older girls. More over records of all functions except standing broad jump was less than those of Japanese in the same age, respectively. 7) The maximum oxygen intake (MOI) was increased considerably with ages and maximum values were 2.93 L/min (boys) and 2.09 L/min (girls) at the age of 17years. This result was almost same as that of the Japanese and Easter Island population, but the value was lower than that of Europe. The average of the maximum oxygen intake per kg body weight per minute from 9 to 17 years of age were around 53 ml in the boys and 42 ml in the girls. 8) Muscle power was increased linearly with ages in boys while there was relatively a little increment in girls. The maximum values of leg muscle in boys and girls at the 17 years of age were 0.168 and 0.088 horse power, respectively. 9) The maximum endurance running time was increased considerably from the age of 9 in boys, while there was no improvement in girls. The maximum values were 6.0 min and 1.8 min, respectively.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.10 no.1
• /
• pp.19-30
• /
• 2005

To investigate the seasonal distribution and grazing impacts of benthic protozoa in mud flat, their abundance, biomass and grazing rates of benthic protozoa were evaluated at interval of two or three month in Gangwha Island from April, 2002 to April, 2004. Heterotrophic flagellates and ciliates accounted for an average 98% of benthic protozoa biomass. Abundance and carbon biomass of heterotrophic flagellates ranged from $0.2{\times}10^5$ to $5.9{\times}10^5\;cells\;cm{-3}$ and from 0.02 to $9.2\;{\mu}gC\;cm^{-3}$, respectively. Biomass of heterotrophic flagellates was high in spring and fall, and showed no differences among stations. Abundance and biomass of heterotrophic flagellates decreased with the depth and were high within the surface 2.5 m sediment layer. The majority of heterotrophic flagellates were less than $10\;{\mu}m$ in length, and few euglenoid flagellates were larger than $20\;{\mu}m$. Abundance and carbon biomass of ciliates ranged from $0.1{\times}10^3$ to $17.8{\times}10^3\;cells\;cm^{-3}$ and from 0.02 to $9.1\;{\mu}gC\;cm^{-3}$, respectively, and those of ciliates were high in spring and fall. Biomass of ciliates was high within the surface 2.5 mm sediment layer and was higher at st. J2 and st. J3 than st. J1. Among the revealed benthic ciliates, the hypotrichs were the most important group in terms of abundance and biomass. During the sampling periods, an average 66% of benthic protozoa biomass was covered by ciliates. The seasonal distribution of benthic protozoa showed an almost similar fluctuation pattern to that of chlorophyll-a. The results suggest that the biomass of benthic protozoa were mainly controlled by prey abundance, for example, diatoms. Based on ingestion rates, benthic protozoa removed from 13.4 to 40.7% of bacterial production and from 20.1 to 36.4% of primary production. Ingestion rates of benthic protozoa on bacteria and microphytobenthos were high in April. Benthic protozoa in this study area may play a pivotal role in the carbon flow of the benthic microbial food web during spring.

• Journal of Korean Dental Science
• /
• v.1 no.1
• /
• pp.28-34
• /
• 2008

Objectives. The objectives of this study were: 1) to compare the effect of varying timing of light curing on shear bond strength, and; 2) to compare the shear bond strength of three self-adhesive cements. Materials and methods. A total of 72 extracted non-carious teeth were divided into 24 for Unicem tests, 24 for Maxcem tests, and 24 for Biscem tests; they were assigned 3 * 2 subgroups of 12 teeth each. The specimens were prepared as follows: 1) The calculus and periodontal ligament were removed from the teeth; 2) The teeth were stored in normal saline; 3) The occlusal enamel of each tooth was removed using high-speed coarse diamond burs under water cooling, and; 4) Finally, the teeth were flattened by 600-grit silicone carbide paper disks. Resin blocks were adhered using either Unicem, Maxcem, or Biscem. Light curing timing was divided into two groups: U10, M10, and B10 were exposed to light after 10 seconds, and; U150, M150, and B150 on the other side were exposed to light after 150 seconds. Shear bond strength was measured by a Universal testing machine with cross head speed of 1mm/min. T-test and One way ANOVA were used for the statistical analysis of data. Results. The shear bond strength of U150 was not significantly higher than that of U10 (U150: 20.55.7Mpa, U10: 18.73.80Mpa). On the other hand, the shear bond strength of M150 was significantly higher than that of M10. The shear bond strength of B150 was also significantly higher than that of B10 (M150:14.45.7Mpa, M10: 9.94.2Mpa, B150: 24.38.3Mpa, B10: 17.27.3Mpa). When the light curing timing was 10sec after bonding, the shear bond strength of Unicem was highest; the shear bond strength of Biscem was highest when the light curing timing was 150sec after bonding (U10: 18.73.80Mpa, B150: 24.38.3Mpa). Significance. Since Unicem is less sensitive based on light curing timing, dentists seem to use it without considering the light curing timing. Maxcem showed the lowest bonding strength (especially M10). Thus, when using Maxcem, dentists need to delay the light curing after adhesion.

• Journal of Animal Science and Technology
• /
• v.46 no.3
• /
• pp.397-404
• /
• 2004

Turkey thigh meats with skin were ground twice through a 3-mm plate and patties were prepared. Patties were cooked using 5 different methods(oven cooking, pan frying, oil deep frying, boiling, and microwaving) to an internal temperature of 85${\sim}90^{\circ}C$ and packaged in either oxygen permeable PVC zipperbags or oxygen impermeable PVDC bags. The samples were analyzed for thiobarbituric acid reactive substances(TBARS) and cholesterol oxidation products(COPs) after storage at $4^{\circ}C$. The TBARS of cooked meat increased during the storage regardless of cooking methods, vacuum packaged thigh meat produced less TBARS and COPs than the aerobically packaged samples. At the beginning of storage, aerobically packaged meat cooked by boiling method produced higher TBARS than that of others. However, the TBARS of microwaved meat with vacuum packaging increased rapidly after 3 days of storage at $4^{\circ}C$. The amount of total COPs in cooked thigh meat increased linearly with storage time. The level of total COPs in aerobically packaged cooked meat was higher than the vacuum-packaged meat. Microwave produced higher level of total COPs in meat than other cooking methods during storage.