• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.34 no.3
• /
• pp.296-302
• /
• 1989

The mesocotyl elongation, having much effect on emergence and stand establishment in the direct sowing culture of rice, was investingated and summarized as follows: As to origin of cultivars, the average lengths of mesocotyl were 9.6 mm in the Indica-Japonica hybrid cultivars, 4.4 mm in the native cultivars and 3.2mm in the Japonica type, respectively. The mesocotyl lengths were tjereh, aman, aus, boro and bulu in order, with the mesocotyl lengths of 29.3mm and 5.4 mm in tjereh and bulu, respectively. The mesocotyl lengths were great in Baekkyungjo, Dadajo & Hejo among the native cultivars, in Sangpungbyeo, Paltal & Gokyangdo of the Japonica type and in Weonpungbyeo, Gayabyeo, Milyang 30 & Sujeongbyeo in Indica- Japonica hybrid cultivars, respectively. The mesocotyl length was the greatest at the seeds sampled I week after flowering (39. 3mm in length), and became decreased with the longer grain-filling. The mesocotyl elongated worse with the longer duration of seed storage regardless of seed maturity, and became longer at the 5$^{\circ}C$ storage plot than at the 15 and 25$^{\circ}C$ plots.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.101-106
• /
• 2002

In a bank-to-turn(BTT) missile, if a 2-gimbaled seeker was stabilized using a 2-axis rate gyro mounted along its primary axis, the change of line of sight(LOS) measured by the seeker would be induced by rolling effects due to bank-to-turn(BTT) steering as well as an actual change. It is observed that the body-coupled effects in a homing loop of BTT missile are mainly concerned with the spurious target maneuver and the coupling due to the rate gyro misalignments. In this paper, we formulate a simple linear BTT homing loop model with seeker model including each body-coupling. With the model, we analyze the effects of the couplings on the homing loop stability, and propose a direct linear compensator for the coupling to recover the stability.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1233-1242
• /
• 2017

Various attempts have been made to prevent crime risk. One of the cases where outdoor pedestrians are attacked by criminals is the abnormal health condition. When a mental or mental condition that can not sustain normal walking due to drunkenness is exposed, the case of being a crime is revealed through crime case analysis. In this study, we propose a method for estimating the state of an individual that can be detected in outdoor activities. In order to avoid the inconvenience of installing a separate terminal for event information transmission of sensors and sensors, it is possible to estimate an abnormal state by using a 3-axis acceleration sensor built in a smart phone. The state of the user can be estimated by analyzing the momentum of the user and analyzing it with the passage of time. It is possible to distinguish the flow of time at regular intervals, to recognize the activity patterns in each time band, and to distinguish between normal and abnormal. In this study, we have evaluated the total amount of kinetic energy and kinetic energy in each direction of the acceleration sensor and the Fourier transformed value of the total energy amount to distinguish the abnormal state.

• Journal of the wind engineering institute of Korea
• /
• v.22 no.4
• /
• pp.163-169
• /
• 2018

In this study, wind loads exerted on the offshore wind turbine rotor in parked condition were predicted with variations of wind speeds, yaw angles, azimuth angle, pitch angles, and power of the atmospheric boundary layer profile. The calculated wind loads using blade element theorem were compared with those of estimated aerodynamic loads for the simplified blade shape. Wind loads for an NREL's 5 MW scaled offshore wind turbine rotor were also compared with those of NREL's FAST results for more verification. All of the 6-component wind loads including forces and moments along the three axis were represented on a non-rotating coordinate system fixed at the apex of rotor hub. The calculated wind loads are applicable for the dynamic analysis of the wind turbine system, or obtaining the over-turning moment at the foundation of support structure for wind turbine system.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6A
• /
• pp.989-999
• /
• 2006

In this paper, numerical analysis method to perform linear dynamic analysis of bridge considering the road surface roughness and bridge-vehicle interaction when vehicle is moving on bridge is presented. The vehicle and bridge are modeled as three-dimension where contact length of tire and pitching of tandem spring are considered and single truck with 2-axles and 3- axles, and tractor-trailer with 5-axles are modeled as 7-D.O.F., 8-D.O.F., and 14-D.O.F., respectively. Dynamic equations of vehicle are derived from the Lagrange's equation and solution of the equation is obtained by Newmark-${\beta}$ method. The surface roughness of bridge deck for this analysis is generated from power spectral density (PSD) function. Beam element for the main girder, shell element for concrete deck and rigid link between main girder and concrete deck are used. The equations of the motion of bridges are solved by mode-superposition procedures. The proposed procedure is validated by comparing the results with the experimental data by Whittemore and Fenves.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.2
• /
• pp.227-233
• /
• 2015

In this study, an indoor test environment was developed for studying the vision stabilizer of an unmanned vehicle, using a virtual environment and a 6-axis motion simulator. The real driving environment was replaced by a virtual environment based on the Aberdeen Proving Ground bump test course for military tank testing. The vehicle motion was reproduced by a 6-axis motion simulator. Virtual reality driving courses were displayed in front of the vision stabilizer, which was located on the top of the motion simulator. The performance of the stabilizer was investigated by checking the image of the camera, and the pitch and roll angles of the stabilizer captured by the IMU sensor of the camera.

• Journal of Bio-Environment Control
• /
• v.6 no.3
• /
• pp.133-142
• /
• 1997

Most of the greenhouses employ the roll-up type ventilation control system. Torque required to roll-up and down might be theoretically expressed with the weight times radius of the ventilation roll; however, measured torques were two times of the theoretically estimated values. As the window film of roll-up vent is used over the periods of time, the warping and crumpling of the material caused the increase of the torque in addition to a span deformation. Therefore, this study was performed to develop an empirical torque formulae to present basic torque data and to assist the development of roll-up type ventilation control system. The empirically adjusted rolling radius (r＋a) exponentially increased at the maximum span deformation. The coefficient of rolling resistance (Cr) was about 0.7―0.8 depending upon the wrinkle status of film material.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.1001-1009
• /
• 2002

The objective of this study is to determine the range of confinement (or the transverse reinforcement of the reinforced concrete structural walls with the T-shaped cross section subjected to cyclic lateral loads. The range of confinement for transverse reinforcement is related to the location of neutral axis and determined by the magnitude and distribution of compressive strain. The compressive strain depends on the ratio of wall cross sectional area to the floor-plan area, the aspect ratio, configuration, the axial load, and the reinforcement ratios. By affection of flange, the neutral axis appears different depending on positive and negative forces and because of this reason, when web and flange are subjected to compressive stress, the range of confinement for the transverse reinforcement of T-shaped walls would shows different result. Therefore this experimental research focused on the structural characteristics of T-shaped walls and suggested the neutral axis depth through comparing the results of this study with sectional analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.53-63
• /
• 2016

Wheel dynamometers are used to measure dynamic load that is conveyed from the road to a vehicle while driving. In this paper, two types of six-component wheel dynamometers utilizing shear deformation and bending deformation were designed and evaluated. Prior to designing the shear and bending type wheel dynamometers, the shear and bending deformation behaviors of the basic structure of the wheel dynamometer itself were analyzed using finite element analysis. Strain analysis was performed repeatedly in order to obtain a similar output sensing strain for each load component. The design was modified with a bridge circuit in order to minimize coupling strain. The results indicated that the shear type dynamometer was expected to obtain stable characteristics due to uniform strain distribution while the bending type dynamometer was expected to obtain high-quality sensitivity performance due to consistent output sensitivity.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.527-532
• /
• 2016

The effects of gas velocity and solid circulation rate on the axial solid holdup distribution have been determined in a 10 mm-I.D. ${\times}$ 800 mm-high circulating fluidized bed plasma reactor under reduced pressure (1torr). Polystyrene polymer powder and nitrogen gas are used as solid and gas materials respectively. The change of solid circulation rate by a large gas flow rate of the riser (40~80 sccm) is also possible by a relatively small gas flow rate of the solid recirculation part (6.6~9.9 sccm). The solid circulation rate in the reactor under reduced pressure increases with increasing aeration velocity in the solid recirculation part. The axial solid holdup in the riser decreases from the dense at the bottom to the dilute phase at the top section of the riser. Solid holdups at the axial positions in the riser increase linearly with increasing solid circulating velocity. From these results, we could determine the position of plasma load for good plasma ignition, maintain and plasma reaction.