• Journal of the Korean Geotechnical Society
• /
• v.22 no.6
• /
• pp.71-82
• /
• 2006

One of the most popular pre-reinforcement methods of tunnel heading in cohesionless soils would be the fore-polling of grouted pipes, known as RPUM (reinforced protective umbrella method) or UAM (umbrella arch method). This technique allows safe excavation even in poor ground conditions by creating longitudinal arch parallel to the tunnel axis as the tunnel advances. Some previous studies on the reinforcing effects have been performed using numerical methods and/or laboratory-based small scale model tests. The complexity of boundary conditions imposes difficulties in representing the tunnelling procedure in laboratory tests and theoretical approaches. Full-scale study to identify reinforcing effects of the tunnel heading has rarely been carried out so far. In this study, a large scale model testing for a tunnel in granular soils was performed. Reinforcing patterns considered are four cases, Non-Reinforced, Crown-Reinforced, Crown & Face-Reinforced, and Face-Reinforced. The behavior of ground and pipes as reinforcing member were fully measured as the surcharge pressure applied. The influences of reinforcing pattern, pipe length, and face reinforcement were investigated in terms of stress and displacement. It is revealed that only the Face-Reinforced has decreased sufficiently both vertical settlement in tunnel heading and horizontal displacement on the face. Vertical stresses along the tunnel axis were concentrated in tunnel heading from the test results, so the heading should be reinforced before tunnel advancing. Most of maximum axial forces and bending moments for Crown-reinforced were measured at 0.75D from the face. Also it should be recommended that the minimum length of the pipe is more than l.0D for crown reinforcement.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.125-135
• /
• 2009

Statement of problem: Loosening or fracture of the abutment screw is one of the common problems related to the dental implant. Generally, in order to make the screw joint stable, the preload generated by tightening torque needs to be increased within the elastic limit of the screw. However, additional tensile forces can produce the plastic deformation of abutment screw when functional loads are superimposed on preload stresses, and they can elicit loosening or fracture of the abutment screw. Therefore, it is necessary to find the optimum tightening torque that maximizes a fatigue life and simultaneously offer a reasonable degree of protection against loosening. Purpose: The purpose of this study was to present the influence of tightening torque on the implant-abutment screw joint stability with the 3 dimensional finite element analysis. Material and methods: In this study, the finite element model of the implant system with external butt joint connection was designed and verified by comparison with additional theoretical and experimental results. Four different amount of tightening torques(10, 20, 30 and 40 Ncm) and the external loading(250 N, $30^{\circ}$) were applied to the model, and the equivalent stress distributions and the gap distances were calculated according to each tightening torque and the result was analyzed. Results: Within the limitation of this study, the following results were drawn; 1) There was the proportional relation between the tightening torque and the preload. 2) In case of applying only the tightening torque, the maximum stress was found at the screw neck. 3) The maximum stress was also shown at the screw neck under the external loading condition. However in case of applying 10 Ncm tightening torque, it was found at the undersurface of the screw head. 4) The joint opening was observed under the external loading in case of applying 10 Ncm and 20 Ncm of tightening torque. 5) When the tightening torque was applied at 40 Ncm, under the external loading the maximum stress exceeded the allowable stress value of the titanium alloy. Conclusion: Implant abutment screw must have a proper tightening torque that will be able to maintain joint stability of fixture and abutment.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.152-161
• /
• 2023

In general, large-capacity hydrogen storage vessels, typically in the form of vertical cylindrical vessels, are constructed using steel materials. These vessels are anchored to foundation slabs that are specially designed to suit the environmental conditions. This anchoring method involves pre-installed anchors on top of the concrete foundation slab. However, it's important to note that such a design can result in concentrated stresses at the anchoring points when external forces, such as seismic events, are at play. This may lead to potential structural damage due to anchor and concrete damage. For this reason, in this study, it selected an vertical hydrogen storage vessel based on site observations and created a 3D finite element model. Artificial seismic motions made following the procedures specified in ICC-ES AC 156, as well as domestic recorded earthquakes with a magnitude greater than 5.0, were applied to analyze the structural behavior and performance of the target structures. Conducting experiments on a structure built to actual scale would be ideal, but due to practical constraints, it proved challenging to execute. Therefore, it opted for an analytical approach to assess the safety of the target structure. Regarding the structural response characteristics, the acceleration induced by seismic motion was observed to amplify by approximately ten times compared to the input seismic motions. Additionally, there was a tendency for a decrease in amplification as the response acceleration was transmitted to the point where the centre of gravity is located. For the vulnerable components, specifically the sub-system (support columns and anchorages), the stress levels were found to satisfy the allowable stress criteria. However, the concrete's tensile strength exhibited only about a 5% margin of safety compared to the allowable stress. This indicates the need for mitigation strategies in addressing these concerns. Based on the research findings presented in this paper, it is anticipated that predictable load information for the design of storage vessels required for future shaking table tests will be provided.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.2
• /
• pp.63-75
• /
• 2013

The Inner Port Phase 2 area of the Pyeongtaek-Dangjin Port is enclosed by a total of three permeable sea-walls, and the disposal site to the east of the Inner Port Phase 2 is also enclosed by two permeable sea-walls. The maximum tidal range measured in the Inner Port Phase 2 and in the disposal site in May 2010 is 4.70 and 2.32 m, respectively. It reaches up to 54 and 27%, respectively of 8.74 m measured simultaneously in the exterior. Regression formulas between the difference of hydraulic head and the rate of interior water volume change, are induced. A three-dimensional numerical hydrodynamic model for the Asan Bay is constructed incorporating a module to compute water discharge through the permeable sea-walls at each computation time step by employing the formulas. Hydrodynamics for the period from 13th to 27th May, 2010 is simulated by driving forces of real-time reconstructed tide with major five constituents($M_2$, $S_2$, $K_1$, $O_1$ and $N_2$) and freshwater discharges from Asan, Sapkyo, Namyang and Seokmoon Sea dikes. The skill scores of modeled mean high waters, mean sea levels and mean low waters are excellent to be 96 to 100% in the interior of permeable sea-walls. Compared with the results of simulation to obstruct the flow through the permeable sea-walls, the maximum current speed increases by 0.05 to 0.10 m/s along the main channel and by 0.1 to 0.2 m/s locally in the exterior of the Outer Sea-wall of Inner Port. The maximum bottom shear stress is also intensified by 0.1 to 0.4 $N/m^2$ in the main channel and by more than 0.4 $N/m^2$ locally around the arched Outer Sea-wall. The module developed to compute the flow through impermeable seawalls can be practically applied to simulate and predict the advection and dispersion of materials, the erosion or deposion of sediments, and the local scouring around coastal structures where large-scale permeable sea-walls are maintained.

• Korean Journal of Culture and Social Issue
• /
• v.9 no.spc
• /
• pp.107-122
• /
• 2003

The object of this study is to evaluate the prevailing physical and psychosocial conditions regarding occupational low back injury. This study consists of two parts. In the first part of the study, analytic biomechanical model and NIOSH guidelines are applied to evaluate risk levels of low back injury for automobile assembly jobs. Total of 246 workers are analysed. There are 20 jobs having greater back compressive forces than 300kg at L5/S1. Also, there are 44 jobs over Action Limit with respect to 1981 NIOSH guidelines. The relationship between psychosocial factors and low back injury was examined in the second part of the study. A battery of questionnaires concerning the psychosocial stress based on PWI (Psychosocial Well-being Index) and musculoskeletal pain symptoms at low back was completed by 246 workers at the same plant. Results showed that 207 out 246 workers experienced the symptoms and 27 workers were diagnosed as patients. Two groups(low stressed, high stressed) based on PWI score had no significant relationships with both symptoms and results of diagnosis. The relationships between physical work load and psychosocial stress were also analysed. Specifically, some postural factors(vertical deviation angle of forearm, horizontal deviation angle of upperarm, vertical deviation angle of thigh, etc) were highly correlated with psychosocial stress. The results illustrated that PWI scores were associated with some physical workloads. However, psychosocial stress levels couldn't be well related with the pain symptom as well as the actual incidence of low back injury since pain or discomfort regarding low back injury were more complex than that of other musculoskeletal disorders.

• Journal of Biosystems Engineering
• /
• v.2 no.1
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

• The Journal of Industrial Distribution & Business
• /
• v.2 no.2
• /
• pp.5-14
• /
• 2011

Opening agricultural market expansion, reduced purchases through wholesale markets, expanding the influence large retailers of consumer's market such as changes in the distribution system to the farmer's market conditions are changing rapidly. Because of this, retailers of the scaled and chain-store operations was centered on distribution environmental changes of the consumer market place. In producing area due to changes in market conditions in the agricultural production of in producing area distribution organization and the size distribution can not be put off no longer challenge is imminent. If it do not raise forces banded together, the producer is bound to remain as the weak. To support the distribution of this production was introduced in 2000 enable the Activation Project of in producing area distribution. Recent in producing area Changes of Agricultural conditions in order to cope with the Small-scale farmers and small individual farmers are becoming Scaled and specialized. Also, is specific to each item and regional is showing aspects. Government support for Activation Project of in producing area distribution is greatly improved, but in terms of competitiveness on the market still is showing the limitations. The most common of these problems, the market response if in producing area producer's organization and scale of the problem. Equipped for the purpose of consumer market place responsiveness unreasonable propelled outward from the Painter-sized weakens the organizational power. also, Difficult to succeed organizational size is a dissolution or anything within a few years, farmers around the best producer organizations, such as deviation occurs is exposed to a variety of issues. In this study, previous studies refer to the recent changes in agricultural retail environment, background and needs of organization·scaled, Determine the status of the domestic in producing area organizations and derived Problems, look into Domestic and overseas of in producing area organization with best practices for enhancing the competitiveness of the proposed improvement are intended to. In the future, in producing area distribution policy would like to provide direction to the development. The results of the study showed the follwing : 1) enhance utilization and orrganized through the diversification of the agricultural Collection systems. 2) Scaled to achieve through Items of specialized a wide area marketing. 3) Management operating units, such as installation and operating that overseas the best practices " Comite Economique Agricole Regional 'Fruits et Legumes' de Bretagne". 4) To establish a support system that in producing area distribution organization model development for appropriate domestic. In particular, in case of domestic in producing area distribution organization, through the analysis of various case study that a successful organization and scaled. The process of the various challenges arising in organizational scaled and generalization, and by the way he goes about trying to overcome is required. At the end of the study's limitations and future research directions suggested.

• Journal of Korea Entertainment Industry Association
• /
• v.15 no.8
• /
• pp.91-106
• /
• 2021

The purpose of this study is to define the process of leading to self-realization and social solidarity through the process of contents planning, production, and distribution as Contents Activism, and to categorize specific execution steps. Based on this, we try to analyze concrete cases to find out the social meaning and effect of the practice of Contents Activism. As for the research method, after examining the differences between traditional activism and Contents Activism through a review of previous studies, the implementation process of Contents Activism was categorized into 7 steps. By applying this model, this study analyzed two cases of Contents Activism. The first case is the 100 laps challenge in the backyard planned by an elderly man ahead of his 100th birthday in early 2020, when the fear of COVID-19 spread. Sir Tom Moore, who lives in the UK, challenged to walk 100 laps in the backyard to help medical staff from the National Health Service as COVID-19 infections and deaths increased due to a lack of protective equipment. His challenge, which is difficult to walk without assistive devices due to cancer surgery and fall aftereffects, drew sympathy and participation from many people, leading to global solidarity. The second case analyzes the case of 'The Unfreedom of Expression, Afterwards' by Kim Seo-kyung and Kim Woon-seong, who were invited to the 2019 Aichi Triennale special exhibition in Japan. The 'Unfreedom of Expression, After' exhibition was a project to display the Statue of Peace and the lives of comfort women in the Japanese military, but it was withdrawn after three days of war due to threats and attacks from the far-right forces. Overseas artists who heard this news resisted the Triennale's decision, took and shared photos in the same pose as the Statue of Peace on social media such as Twitter and Instagram, empathizing with the historical significance of the Statue of Peace. Activism, which began with artists, has expanded through social media to the homes, workplaces, and streets of ordinary citizens living in various regions. The two cases can be said to be Contents Activism that led to social practice while solidifying and communicating with someone through contents.

• KDI Journal of Economic Policy
• /
• v.32 no.2
• /
• pp.93-143
• /
• 2010

This paper estimates the impact of Japan's economic sanction on DPRK trade in the 2000s. It conceptualizes the effects of sanction on DPRK trade, econometrically tests whether such effects exist in case of Japan's sanction using currently available DPRK trade statistics, and measures the size of the effects by correcting and reconfiguring the deficiencies of the currently available DPRK trade statistics. The main findings of the paper are as follows. First, Japan's sanction can have two different effects on DPRK trade: 'Sanction Country Effect' and "Third Country Effect.' The former means that the sanction diminishes DPRK trade with Japan while the latter refers to the effects on DPRK trade with other countries as well. The third country effect can arise not simply because the DPRK changes its trade routes to circumvent the sanction, but because the sanction forces the DPRK to readjust its major trade items and patterns. Second, currently no official DPRK trade statistics are available. Thus, the so-called mirror data referring to DPRK trading partners' statistics should be employed for the analysis of the sanction effects. However, all currently available mirror data suffer from three fundamental problems: 1) they may omit the real trade partners of the DPRK; 2) they may confuse ROK trade with DPRK trade; 3) they cannot distinguish non-commercial trade from commercial trade, whereas only the latter concerns Japan's sanction. Considering those problems, we have to adopt the following method in order to reach a reasonable conclusion about the sanction effect. That is, we should repeat the same analysis using all different mirror data currently available, which include KOTRA, IMF and UN Commodity Trade Statistics, and then discuss only the common results from them. Third, currently available mirror data make the following points. 1) DPRK trade is well explained by the gravity model. 2) Japan's sanction has not only the sanction country effect but also the third country effect on DPRK trade. 3) The third country effect occurs differently on DPRK export and import. In case of export, the mirror statistics reveal positive (+) third country effects on all of the major trade partners of the DPRK, including South Korea, China and Thailand. However, on DPRK import, such third country effects are not statistically significant even for South Korea and China. 4) This suggests that Japan's sanction has greater effects on DPRK import rather than its export. Fourth, as far as DPRK export is concerned, it is possible to resolve the abovementioned fundamental problems of mirror data and thus reconstruct more accurate statistics on DPRK trade. Those reconstructed statistics lead us to following conclusions. 1) Japan's economic sanction diminished DPRK's export to Japan from 2004 to 2006 by 103 million dollars on annual average (Sanction Country Effect). It comprises around 60 percent of DPRK's export to Japan in 2003. 2) However, for the same period, the DPRK diverted its exports to other countries to cope up with Japan's sanction, and as a result its export to other countries increased by 85 million dollars on annual average (Third Country Effect). 3) This means that more than 80 per cent of the sanction country effect was made up for by the third country effect. And the actual size of impact that Japan's sanction made on DPRK export in total was merely 30 million dollars on annual average. 4) The third country effect occurred mostly in inter-Korean trade. In fact, Japan's sanction increased DPRK export to the ROK by 72 million dollars on annual average. In contrast, there was no statistically significant increase in DPRK export to China caused by Japan's sanction. 5) It means that the DPRK confronted Japan's sanction and mitigated its impact primarily by using inter-Korean trade and thus the ROK. Fifth, two things should be noted concerning the fourth results above. 1) The results capture the third country effect caused only by trade transfer. Facing Japan's sanction, the DPRK could transfer its existing trade with Japan to other countries. Also it could change its main export items and increase the export of those new items to other countries as mentioned in the first result. However, the fourth results above reflect only the former, not the latter. 2) Although Japan's sanction did not make a huge impact on DPRK export, it might not be necessarily true for DPRK import. Indeed the currently available mirror statistics suggest that Japan's sanction has greater effects on DPRK import. Hence it would not be wise to argue that Japan's sanction did not have much impact on DPRK trade in general, simply using the fourth result above.