• 소성∙가공
• /
• 제17권4호
• /
• pp.257-262
• /
• 2008

The control of wire temperature is very important in the fine wire drawing process. The wire speed should be increased, and the wire temperature should be dropped as much as possible. Up to now, the process design of wire drawing process depends on the experiences of experts. In this study, a wire drawing process design method was proposed to increase the productivity. The proposed method of this study includes the pass schedule and the design of a multi pass wire drawing machine. A pass schedule was performed based on the calculation of the wire temperature. Also, a new multi pass wire drawing machine was manufactured to apply the designed pass schedule. Through the wire drawing experiment, the effectiveness of the proposed process design method was evaluated. The final drawing speed was increased from 1,100m/min to 2,000m/min without deterioration of final drawn wire.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권1호
• /
• pp.72-75
• /
• 2007

Magnetization loss of HTS wire is strongly dependent on the critical current density and the aspect ration of the HTS wire. This paper presents the magnetization loss of stacked BSCCO wire and stacked YBCO wires which had different critical current densities. Width of the BSCCO wire was 4mm and widths of two YBCO wires were 4mm and 8mm. Single wire, two stacked three stacked and four stacked wires were fabricated and tested. Ratio of magnetization loss of BSCCO wire to YBCO wire was presented at single wire. For stacked wire, ratio of magnetization loss of single wire to stacked wire was presented. Test results shows that magnetization losses of stacked wires were greater than that of single wire at large high magnetic field above critical magnetic field.

• 센서학회지
• /
• 제18권4호
• /
• pp.322-326
• /
• 2009

To estimate the measurement uncertainty for industrial platinum resistance thermometers(IPRTs) made with 3-wire connection, the immersion temperature profile was investigated using a liquid bath. Two types of IPRTs having lead wires made of silver and nickel were constructed and the immersion profiles were measured at temperatures from -50 $^{\circ}C$ to 250 $^{\circ}C$ using 3-wire and 4-wire method. As immersion depth and temperature increased, the resistances measured by 3-wire method increased linearly but not for 4-wire method. To calibrate a 3-wire IPRT, the immersion effect must be accounted for. We propose a linear equation to assess correctly the measurement uncertainty.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.414-419
• /
• 1995

The wire displacement of wire electric discharge machine has been measured using He-Ne laser. A measurement system consisted of He-Ne laser, A/D converter, 4 divided photodiode, amplifier, sensor process instrument, and personal computer. The processing parameters were varid with feed rate, wire tension, wire speed and voltage. The laser beam intensity transmitted on a 4 divided photodiode was varied by processing wire electric descharge machine with various process parameters. The 4 divided photodiode and amplifier were used to change the detected beam intensity into voltage. Variation of wire displacement was between 11 and 125 .mu. m. The wire tension was dominant on the variation of wire displacement among many parameters.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.856-860
• /
• 2008

Wire-suspensions in the conventional actuators mechanically support the moving part and guarantee the accuracy of the actuator without tangential tilt actuation. However, such a suspension configuration has considerable stiffness in the tangential tilt direction with two additional wire beams for the tangential tilt. Thus, we performed a design sensitivity analysis for the wire-suspension stiffness of 4-axis actuator and controlled the main parameters such as distance among wire-suspensions and wire-suspension length to allow tangential tilt flexibility. The elasticity of frame PCB that supports the moving part by wire-suspensions was also exploited to improve the flexibility of wire-suspension in the tangential tilt direction. A novel suspension structure was devised by establishing eight wire-suspensions at both sides of the moving part for electrical connection to coils. The magnetic circuit according to the proposed 4-axis actuator using multi-polar magnet and coils was also suggested for the generation of electromagnetic forces in the focusing, tracking, radial and tangential tilt directions.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.349-351
• /
• 1999

This paper presents a new control algorithm for series active power filters that are applied to 3-phase 3-wire and 3-phase 4-wire systems with capacitive loads. It is difficult to reduce harmonic currents in neutral lines of the 3-phase 4-wire systems using conventional series active power filter control methods. 3-phase 4-wire series active power filter systems using the proposed method in this study lower neutral line harmonics. Simulation was carried out to verify the algorithm.

• 청정기술
• /
• 제22권4호
• /
• pp.281-285
• /
• 2016

난분해성 1,4-다이옥산을 분해시키기 위하여 촉매습식과산화반응에 활성적인 Cu wire촉매를 사용하였다. Cu wire 촉매를 사용함으로써 1,4-다이옥산의 완전한 분해가 가능하였으나, 분해된 1,4-다이옥산은 완전 무기화($CO_2$와 $H_2O$로 전환)되지 못하고 중간생성물인 ethylene glycol diformate, oxalic acid, formic acid, formaldehyde, acetaldehyde 등으로 전환되었다. 1,4-다이옥산이 분해되어 없어짐에 따라 formaldehyde와 oxalic acid가 점진적으로 나타나기 시작하여 증가하다가 최고농도를 보인 후 다시 감소하였다. 이들 두 중간체의 최고농도 도달시점에 acetaldehyde의 농도가 급격히 증가하여 최고농도를 보인 후 다시 감소하였다. 이들 세가지 중간물질의 감소와 함께 ethylene glycol diformate, formic acid가 생성되기 시작하여 그 농도가 점진적으로 증가하였다. 이들은 연속적인 과정을 통해 생성되었다. Cu wire 촉매는 반응이 진행되는 동안 활성이 떨어지지 않고 매우 안정적이었다.

• 대한치과교정학회지
• /
• 제22권4호
• /
• pp.823-836
• /
• 1992

Guiding a tooth along an arch wire results in a counteracting frictional force among arch wires, bracket and ligature. This frictional forces should be eliminated or minimized when orthodontic teeth movement is being planned. The purpose of this study was to evaluate the changes of width, cross-sectional forms and surface morphologies of stainless steel wire and $Elgiloy^{\circledR}$ wire after electropolising. Experimental variables included in this experiment were arch wire materials, current, electrolyte temperature and polishing time. Wire widths were measured by micrometer and cross-sectional forms and surface morphologies were examined with optical microscope and scanning electron microcope. The results were as follows: 1. The mean and standard deviation of widths of stainless steel wire and $Elgiloy^{\circledR}$ wire varying polishing time with condition of $249A/dm^2$ and $20^{\circ}C,\;249A/dm^2$ and, $332A/dm^2$ and $20^{\circ}C$ and $332A/dm^2$ and $250^{\circ}C$ were obtained. 2. With increasing polishing time, the widths of stainless steel wire and $Elgiloy^{\circledR}$ wire became decreased proportionally 3. The changes of widths of stainless steel wire and $Elgiloy^{\circledR}$ wire were statistically insignificant between $20^{\circ}C$ group and $25^{\circ}C$ group, but significant between $249A/dm^2$ group and $332A/dm^2$ group. 4 The cross-sectional forms of wire after electropolishing were not changed in stainless steel wire, and while it were changed to rounded corners in $Elgiloy^{\circledR}$ wire. 5. The surface morphologies of wire after electropolishing were scratch-absent and more smoothened both in stainless steel wire and $Elgiloy^{\circledR}$ wire.

• 소성∙가공
• /
• 제27권4호
• /
• pp.244-249
• /
• 2018

Rhodium is a representative platinum group material. Rhodium is used in several industrial fields including jewelry, chemical reaction catalyst, electric component etc. In recently, ultra-fine rhodium wire has been applied to the pins of probe card used to test a semiconductor. In this study, in order to produce a fine rhodium wire with the diameter of $50{\mu}m$, a fine rhodium wire drawing process was designed. After design of the fine wire drawing process by using a uniform reduction ratio theory, finite element analysis was performed. Finally, fine wire drawing experiment was performed to verify the effectiveness of the designed process.

• 대한치과교정학회지
• /
• 제22권3호
• /
• pp.647-656
• /
• 1992

The purpose of this study was to evaluate the elastic memory process in cold worked stainless steel wire and the effect of heat treatment on it. 0.018 inch round and $0.019\times0.025$ inch rectangular wire (ORMCO stainless wire) were used in this study. Each wire type had 4 groups: non-heat treatment group, furnace heat treatment group, electric current heat treatment group, and bending after heat treatment group. Each group was consisted of 10 specimens. With the Jig, each wire was bent into v-shape uniformly, and width of two free ends of each v-shaped wire was measured by caliper (to the point of 0.1 mm correctly) at time interval of offjig, after heat treatment, 1, 2, 3, 4 hours, 1, 2, 3, 4, 5, 6 days, 1, 2, 3, 4 weeks after. The results were as follows: 1. In non-heat treatment group and bending after heat treatment group, elastic memory process was occured $60\%$ within 1 hour, and more than $90\%$ within 1 week. 2. In furnace and electric current heat treatment group, almost all elastic memory process was occured during teat treatment, and then specimen was stabilized dimensionally. 3. Magnitude of deformation by elastic memory was greater in heat treatment group than non heat treatment group and bending after heat treatment group. 4. There was no remarkable difference in deformation pattern between 0.018 inch round wire and $0.019\times0.025$ inch rectangular wire.