• Journal of Surface Science and Engineering
• /
• v.50 no.3
• /
• pp.198-205
• /
• 2017

Thermal dissipation was investigated for poly methyl methacrylate (PMMA) composite films containing graphite and multi wall carbon nanotube(CNT) powders as filler materials. After mixing PMMA with fillers, solvent, and dispersant, the pastes were prepared by passing through a three roll mill for three times. The prepared pastes were coated $15{\sim}40{\mu}m$ thick on a side of 0.4 mm thick aluminium alloy plate and dried for 30 min at $150^{\circ}C$ in an oven. The content of fillers in dried films was varied as 1, 2, and 5 weight % maintaining the ratio of graphite and CNT as 1:1. Raman spectra from three different samples exhibited D, G and 2D peaks, as commonly observed in graphite and multi wall CNT. Among those peaks, D peak was prominent, which manifested the presence of defects in carbon materials. Thermal emissivity values of three samples were measured as 0.916, 0.934, and 0.930 with increasing filler content, which were the highest ever reported for the similar composite films. The thermal conductivities of three films were measured as 0.461, 0.523, and $0.852W/m{\cdot}K$, respectively. After placing bare Al plate and film coated samples over an opening of a polystyrene box maintained for 1 h at $92^{\circ}C$, the temperatures inside and outside of the box were measured. Outside temperatures were lower by $5.4^{\circ}C$ in the case of film coated plates than the bare one, and inside temperatures of the former were lower by $3.6^{\circ}C$ than the latter. It can be interpreted that the PMMA composite film coated Al plates dissipate heat quicker than the bare Al plate.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.377-385
• /
• 2015

The span-lengthening of PSC I girder has increased the risk of lateral instability of the girder with the increases in the aspect ratio and self-weight of the girder. Recently, collapses of PSC I girder during construction raise the necessity of evaluating the lateral instability of the girder. Thus, the present study evaluated the lateral behavior and instability of PSC I girders under wind load, regarded as one of the main causes of the roll-over collapse during construction. Lateral instability of the girder is mainly dependent on the length of the girder and the stiffness of the support. The analysis results of this study showed the decrease in the critical wind load and the increase in the critical deformation and angle of the girder, leading to the lateral instability of the girder. Finally, this study proposed analytical equations that can predict the critical amount of wind load and lateral deformation of the girder, which would provide quantitative management values to maintain lateral stability of PSC I girder during construction.

• Particle and aerosol research
• /
• v.9 no.4
• /
• pp.261-269
• /
• 2013

The chemical mechanical polishing (CMP) process is widely used in semiconductor manufacturing process for planarization of various materials and structures. Point-of-use (POU) filters are used in most of the CMP processes in order to reduce the unwanted micro-scratches which may result in defects. The performance of the POU filter is depends on type and size of the abrasives used during cleaning process. For this reason, there is a need to evaluate POU filters for their filtration efficiency (FE) with different types of abrasives. In this study, we developed filter test system to evaluate the FE of POU using ceria and silica abrasives (slurry). The POU filter is roll type capsule filter with retention size of 0.2 ${\mu}m$. Two POU filters of different make are evaluated for FE. We observed that both POU filters show similar filtration efficiency for silica and ceria slurry. Results reveal that the ceria slurry and the colloidal silica particle are removed not only by mechanical way but also hydrodynamic and electrostatic interaction way.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.683-690
• /
• 2012

In this work, the semi-active control of a large-sized bus suspension system with an MR damper was studied. An MR damper model that can aptly describe the hysteretic characteristics of an MR damper was adopted. Parameter values of the MR damper model were suitably modified by considering the maximum damping force of a passive damper used in the suspension system of a real large-sized bus. In addition, a fuzzy logic controller was developed for semi-active control of a suspension system with an MR damper. The vertical acceleration at the attachment point of the MR damper and the relative velocity between sprung and unsprung masses were used as input variables, while voltage was used as the output variable. Straight-ahead driving simulations were performed on a road with a random road profile and on a flat road with a bump. In straight-ahead driving simulations, the vertical acceleration and pitch angle were measured to compare the riding performance of a suspension system with a passive damper with that of a suspension with an MR damper. In addition, a single lane change simulation was performed. In the simulation, the lateral acceleration and roll angle were measured in order to compare the handling performance of a suspension system using a passive damper with that of a suspension system using an MR damper.

• Journal of the Korean Society of Physical Medicine
• /
• v.9 no.4
• /
• pp.455-463
• /
• 2014

PURPOSE: The purpose of this study was to compare the effects of Graston and self-myofascial release (SMR) techniques on knee joint flexibility, hamstring, and quadriceps strength. METHODS: Twenty subjects with hamstring shortness participated in this study. The subjects were assigned randomly to one of two groups: The Graston technique (GT) group received intervention using a Graston instrument for one minute, and the SMR group performed self-exercises using a foam roll for one minute. The range of motion (ROM) of the knee joint was measured by active knee extension test, and a handheld dynamometer was utilized to collect the hamstring and quadriceps muscle strength. This experiment was performed by two physical therapists. The significant level was set at ${\alpha}$=0.05. RESULTS: The results were as follows: 1) The ROM of the knee joint and quadriceps muscle strength were significantly increased in both groups. 2) Hamstring muscle strength was significantly reduced in both groups. 3) There were no significant differences between the GT group and SMR group for any variable. CONCLUSION: The results of this study suggest that SMR is an effective and easy technique for restoring proper muscle length and strength in subjects with hamstring shortness. We recommend that SMR technique be used for treat hamstring shortness in clinical setting and home-program.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.4
• /
• pp.443-450
• /
• 2012

In this study, This study investigates the axial load behavior of concrete-filled steel columns using seismic rectangular steel tube with the width-to-thickness and slenderness ratio. Due to cold-roll forming and cold-press forming of steel tube, the flat part and the corner part of the rectangular steel tubes are changed in the material properties compared to SN-steel plate. It was showed the tendency to increase yield strength, tensile strength and upper limit of yield ratio This phenomenon affects the nonlinear behavior after local buckling of the steel tube. Therefore, the coupon test was performed by the processing of rectangular steel tube, in order to assess forming performance. And a total of 6 CFT-columns were tested under monotonic loading condition. Main parameters were the width-thickness ratio and the slenderness ratio.

• Journal of Ginseng Research
• /
• v.14 no.2
• /
• pp.317-331
• /
• 1990

Nitrogen compounds of Panax ginseng and their biological activities in plant and animal were reviewed. Major nitrogen combounds found in P. ginseng are free amino acids, Water soluble teins, insoluble proteins and peptides. Minor nitrogen compounds are dencichine. glycol)roteins. amines, alkaloides, methoxy or alkyl pyrazine derivatives. free nucleosides and nllrleir arid bases. 4-me- thymi-5-thiazoleethanol and pyroglutamic acid. The contents of total nitrogen and protein in root increased until 13 years old rvhich was the highest age tinder investigation. Soluble protein content increased With the root weight and was higher in xylem pith than cortex-epidermis indicating the rlosc relation with root growth. Arginine which covered 58% of total free amino aroids may serve as a storage nitrogen. Arginine seems to be changed into proline in rhizome, threonine in stem and again threoning and arginine in leaf. The greater the root weight the higher the polyaminc content. Polyamine stimulated the growth of root callus. Physiological roles of other minor nitrogen compounds are unknown although dencichine content is relatively high (0.5% d.w.). biochemical and pharmatological activities of some nitrogen compounds for animal were more investigated than physiological roll iota plant itself. Radiation and U.V. protective function (heat stable protein), insulin-like activity in lipogenesis and lipolysis (adenosine and pyroglutamic acid), depression of blood sugar content (glycopeptide). hemostatir and nellrotoxic activity (denrichine) and. sedative and hypnotic activity (4-methyl-5-thiazoleethilnol) are reported. Heat stable protein increased with root age. The traditional quality critsria appear to be well in accordance with biological activities of nitrogen compounds. Chemical stlldies of nitrogen compounds seem relatively rare, probably dole to difficulty of isolation, subsequently the investigations of biological activities are little.

• Journal of Bio-Environment Control
• /
• v.6 no.4
• /
• pp.242-249
• /
• 1997

Environmental control operations have been considerably contributed to the reduction of labor cost in both plastic film and glass greenhouses since government supported projects were begun. However, some problems are still remaining on the optimal environmental control and excessive operation due to an inflexible software regulating ventilation gear - reducers. The unadjustable software caused the damage of ventilation system, resulting in heat stresses of crops. This study was performed to develop a ventilation software controlling the vent opening level, opening sequence, based on the wind direction, and control interval according to the difference between ambient and set- up temperatures. The software included a beeper system alarming urgent cases, while a manager was remote from the greenhouse. A compatible hardware with the software was also developed by using a low-cost diffused DSP controller.

• Journal of Korean Neurosurgical Society
• /
• v.51 no.4
• /
• pp.203-207
• /
• 2012

Objective: The purpose of this prospective study was to evaluate the efficacy and safety of screw fixation without bone fusion for unstable thoracolumbar and lumbar burst fracture. Methods: Nine patients younger than 40 years underwent screw fixation without bone fusion, following postural reduction using a soft roll at the involved vertebra, in cases of burst fracture. Their motor power was intact in spite of severe canal compromise. The surgical procedure included postural reduction for 3 days and screw fixations at one level above, one level below and at the fractured level itself. The patients underwent removal of implants 12 months after the initial operation, due to possibility of implant failure. Imaging and clinical findings, including canal encroachment, vertebral height, clinical outcome, and complications were analyzed. Results: Prior to surgery, the mean pain score (visual analogue scale) was 8.2, which decreased to 2.2 at 12 months after screw fixation. None of the patients complained of worsening of pain during 6 months after implant removal. All patients were graded as having excellent or good outcomes at 6 months after implant removal. The proportion of canal compromise at the fractured level improved from 55% to 35% at 12 months after surgery. The mean preoperative vertebral height loss was 45.3%, which improved to 20.6% at 6 months after implant removal. There were no neurological deficits related to neural injury. The improved vertebral height and canal compromise were maintained at 6 months after implant removal. Conclusion: Short segment pedicle screw fixation, including fractured level itself, without bone fusion following postural reduction can be an effective and safe operative technique in the management of selected young patients suffering from unstable burst fracture.

• Molecular & Cellular Toxicology
• /
• v.4 no.4
• /
• pp.307-310
• /
• 2008

AAD16034 is an alginate lyase from Pseudoalteromonas sp. IAM14594. A very close homologue with known 3D structure exists (marine bacterium Pseudoalteromonas sp. strain no. 272). A three-dimensional structure of AAD16034 was generated based on this template (PDB code: 1J1T) by comparative modeling. The modeled enzyme exhibited a jelly-roll like structure very similar to its template structure. Both enzymes possess the characteristic alginate sequence YFKhG+Y-Q. Since AAD16034 displays enzymatic activity for poly-M alginate, docking of a tri-mannuronate into the modeled structure was performed. Two separate and adjacent binding sites were found. The ligand was accommodated inside each binding site. By considering both binding sites, a plausible binding pose for the poly-M alginate polymer could be deduced. From the modeled docking pose (i.e., the most important factor that attracts alginate polymer into this lyase) the most likely interaction was electrostatic. In accordance with a previous report, the hydroxyl group of Y345 was positioned close to the ${\alpha}$-hydrogen of ${\beta}$-mannuronate, which was suitable to initiate a ${\beta}$-elimination reaction. K347 was also very near to the carboxylatemoiety of the ligand, which might stabilize the dianion intermediate during the ${\beta}$-elimination reaction. This implies that the characteristic alginate sequence is absolutely crucial for the catalysis. These results may be exploited in the design of novel enzymes with desired properties.