• Structural Engineering and Mechanics
• /
• 제76권6호
• /
• pp.725-736
• /
• 2020

In this work the mixed mode I/III fracture of sandstone has been studied experimentally and numerically. The experimental work used three-point bending specimens containing pre-existing cracks, machined at various inclination angles so as to achieve varying proportions of mode I to mode III loading. Dimensionless stress intensity factors were calculated using the extended finite element method (XFEM) for and compared with existing results from literature calculated using conventional finite element method. A total of 28 samples were used to conduct the fracture test with 4 specimens for each of 7 different inclination angles. The fracture load and the geometry of the fracture surface were obtained for different mode mixities. Prediction of the fracture loads and the geometry of the fracture surface were made using XFEM coupled with a cohesive zone model (CZM) and showed a good comparison with the experimental results.

• 한국항공우주학회지
• /
• 제48권7호
• /
• pp.505-511
• /
• 2020

원형 복합재 튜브를 고고도 장기체공 무인기의 주요 스파에 사용하였다. 본 논문에서는 수정된 Brazier 방법을 이용하여 비대칭으로 보강된 원형 스파의 파단하중을 예측할 수 있는 이론적인 모델을 제안하였다. 이 모델을 이용하여 비대칭으로 보강된 원형스파의 최대 허용 굽힘 모멘트를 예측하였다. 해석 결과로부터 원형 스파의 상단에 위치한 보강된 캡은 최대 허용 굽힘 모멘트를 증가시키는 것을 알 수 있다. 4점 굽힘 실험을 수행하여 스파 캡이 파손하중에 미치는 영향을 평가하였고 제안된 모델과 비교하였다. 그리고 수치해석을 수행하여 보강된 원형 스파의 거동을 분석하였다. 제안된 이론적인 모델은 실험 및 수치해석 결과와 잘 일치함을 보였다.

• Journal of Welding and Joining
• /
• 제9권4호
• /
• pp.17-27
• /
• 1991

The direct brazing technology which could be used for the simplification of brazing process and the improvement of brazed joint quality was studied with $Al_2O_3$ and stainless steels. The brazing of $Al_2O_3$ to STS304 or STS430 was performed under different brazing conditions such as brazing filler metal, temperature, heating rate and brazing time. Microstructural observation and chemical analysis be SEM/EPAM were carried out to verify the quality of brazed joints. 4-point bending strength of brazed joints was also measured to find the optimal brazing conditions. The results showed that, in brazing of $Al_2O_3$, the mixed oxide layer resulted from the reaction between Ti in filler metal and oxide layer on the material surface to be brazed was found to be bery important for the joint quality. The width of oxide layer varied with the brazing conditions such as brazing time, heating rate and chemical composition of filler metals. The strength of brazed joints was more affected by the type of materials and their thermal properties than by brazing heat cycle.

• Wind and Structures
• /
• 제32권4호
• /
• pp.341-354
• /
• 2021

Articulated towers are one of the class of compliant offshore structures that freely oscillates with wind and waves, as they are designed to have low natural frequency than ocean waves. The present study deals with the dynamic response of a double-pendulum articulated tower under hydrodynamic and aerodynamic loads. The wind field is simulated by two approaches, namely, single-point and multiple-point. Nonlinearities such as instantaneous tower orientation, variable added mass, fluctuating buoyancy, and geometrical nonlinearities are duly considered in the analysis. Hamilton's principle is used to derive the nonlinear equations of motion (EOM). The EOM is solved in the time domain by using the Wilson-θ method. The maximum, minimum, mean, and standard deviation and salient power spectral density functions (PSDF) of deck displacement, bending moment, and central hinge shear are drawn for high and moderate sea states. The outcome of the analyses shows that tower response under multiple-point wind-field simulation results in lower responses when compared to that of single-point simulation.

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.957-962
• /
• 2009

Sialon was produced by hot-pressing the mixtures of $Si_3N_4$, AlN and $Y_2O_3$ powders. All fracture tests were performed on a three-point loading system with a 30 mm bending span. Fracture toughness and Vickers hardness of smooth specimen were average 7.05 $MPa{\cdot}m^{0.5}$ and Hv = 1580, respectively. Density of three kinds of specimens, smooth specimen, smooth and healed specimen, smooth with $SiO_2$ colloidal coating and healed specimen, had beyond 99 % of theoretical density. Bending strength of smooth healed specimens had high strength more than 1 GPa. Crack healed specimens recovered as strength as smooth specimen. That is, cracked specimen with $SiO_2$ colloidal coating on cracked part recovered strength by heat treatment, completely. Crack healing of $Si_3N_4$ composite ceramics had contributed glassy $SiO_2$ to strength recovery. Limiting high temperature for bending strength of heat treated smooth specimen for bending strength was about 1273 K.

• 대한기계학회논문집A
• /
• 제21권10호
• /
• pp.1541-1550
• /
• 1997

Since the ceramic/metal joint material is made at a high temperature, the residual stress develops when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of Si$_3$N$_4$STS304 joints quantitatively and to compare the strength of joints. The difference of residual stress is measured when repeated thermal cycl is loaded, under the conditions of the practical use of the ceramic/metal joint. The residual stress increases at 1 cycle of thermal load but decreases in 3 cycles to 10 cycles of thermal load. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a result, it is known that the stress of joint decreases as the number of thermal cycle increases.

• 한국항공우주학회지
• /
• 제32권3호
• /
• pp.17-21
• /
• 2004

테이프래핑 구조물은 유도무기의 노즐 구조에 많이 사용되고 있는데 주로 주자직 복합재료를 띠모양으로 이은 다음 이를 맨드럴에 경사각을 가지게 감는 방법으로 제작된다. 적층된 구조물은 고압의 오토클레이브나 하이드로 클레이브에서 성형된다. 테이프래핑 구조물은 적층 형태가 일방향 복합재료의 경우와는 다르며, 제작 시 주어진 경사각을 고려한 해석이 필요하다. 본 연구에서는 테이프래핑 구조물에 대한 해석 기법을 고찰하였다. 먼저 4점 굽힘 실험에 대한 유한요소 해석 결과와 실험 결과를 비교함으로써 테이프래핑 구조물의 모델링 기법의 타당성을 검증하였다. 4점 굽힘 실험의 파단 하중과 이방성 파단 판정식의 결과를 비교함으로써 최적의 이방성 파단 판정식을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1349-1352
• /
• 2005

This paper is to investigate a defect for thermal barrier coating layers by acoustic emission method in 4-point bending test. The two-layer thermal barrier coating is composed of $150\mu{m}\;CoNiCrAlY\;bond\;coating\;by\;vacuum\;plasma\;spray(VPS)\;process\;and\;250\mu{m}\;ZrO_2-8wt%Y_2O_3$ ceramic coating layer by air plasma spray(APS) process on Inconel-718. The specimen prepared by cyclic thermal test(500, 1000, 2000cycle) at $1050^{\circ}C$ The AE monitoring system is composed of PICO type sensor, a wide band pre-amplifier(40dB), PC and AE DSP(16/32 PAC) board. The AE event, amplitude, Cumulative energy and count of coating specimens is evaluated according to cyclic thermal test.

• 한국재료학회지
• /
• 제11권3호
• /
• pp.221-226
• /
• 2001

사파이어 ($\alpha$-$Al_2$$O_3$) 단결정에 있어 basal slip (0001)1/3<1120>의 전위속도를 4점 곡강도를 이용하여, 측정하였다. 이 곡강도는 온도 $1200^{\circ}C$ 에서 $1400^{\circ}C$ 그리고 응력은 90MPa, 120MPa, 160MPa에서 행하여졌다. 전위속도는 4 점굽힘 시편의 굽힘변위속도에 의해 구하여졌다. 얻어진 전위속도를 이용하여 전위속도의 온도 및 응력 의존성에 대해 검토하였다. 전위속도의 온도의존성을 이용하여 basal slip 전위속도를 위한 활성화에너지를 구하였으며, 그 값은 대략 2.2$\pm$0.4eV이었다. 한편, 전위속도의 응력의존성을 나타내는 응력지수 m은 2.0$\pm$0.2이었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1647-1650
• /
• 2003

The Objective of this work was to design Surface Antenna Structure (SAS) and investigate fatigue behavior of SAS that was asymmetric sandwich structure. This term, SAS, indicates that structural surface becomes antenna. Constituent materials were selected considering electrical properties, dielectric constant and tangent loss as well as mechanical properties. For the antenna performance, SSFIP elements inserted into structural layers were designed for satellite communication at a resonant frequency of 12.5 GHz and final demonstration article was 16${\times}$8 array antenna. From electrical measurements, it was shown that antenna performances were in good agreement with design requirements. In cyclic 4-point bending, flexure behavior was investigated by static and fatigue test. Fatigue lift curve of SAS was obtained. The fatigue load was determined experimentally at a 0.75(1.875kN) load level. SAS concept is the first serious attempt at integration for both antenna and composite engineers and promises innovative future communication technology.