• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.465-470
• /
• 2020

Heterolayered K(Ta,Nb)O₃/Pb(Zr,Ti)O₃ thin films on Pt/Ti/SiO₂/Si substrates were prepared by a sol-gel process and spin-coating method. The structural and electrical properties were measured to investigate the possibility of application as an electrocaloric effect device. All specimens exhibited dense and uniform cross-sectional structures without pores, and the average thickness of the specimen coated six times was approximately 394 nm. Curie temperatures were observed at 5℃ or less in type-I and 10℃ in type-II specimens, respectively. Type-II specimens coated 6 times showed a relative dielectric constant of 758 and remanent polarization of 9.71 μC/㎠ at room temperature. The maximum electrocaloric effect occurred between 20 and 25℃, slightly higher than their Curie temperature, and the electrocaloric property (ΔT) of the type-II specimens coated 6 times was approximately 1.2℃ at room temperature.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.7
• /
• pp.1213-1217
• /
• 2008

Poling is an important process in fabricating PZT ceramic devices such as filters and resonators and activates piezoelectricity to sintered PZT ceramics. Tolerance of the operating frequency of these devices is tightly required in applications. And a factor to attribute the tolerance is the temperature dependence of the resonance frequency of PZT ceramics. In this paper the relationship of poling strength and temperature dependence of resonance frequency of PZT specimens was studied. The $Pb(Zr_{0.53}Ti_{0.47})O_3$ ceramics were fabricated and the poling strengths were chosen to be 0.5, 1.5, 2.5 and 3.5 [kV/mm]. The dielectric constant of the specimen poled in poling strength 0.5 [kV/mm] was less than that of unpoled specimen and the specimen poled in higher electric field had the higher dielectric constant. (002) peak in X-ray diffraction patterns of the specimens increased as poling strength increased. And the change of resonance frequency of the specimens according to the variation of temperature was measured. Resonance frequency of all specimens increased as the temperature increased. The specimen poled in higher electric field had the smaller positive temperature coefficient of resonance frequency. The effect that temperature coefficient of resonance frequency becomes smaller is obtained when Zr mole in PZT composition equation increase. Controlling the poling strength is believed to be a method to adjust the temperature stability of resonance frequency of the PZT ceramic devices.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.799-801
• /
• 1988

This paper was studied on the effects of Ca-La-Nb substitution and Zr/Ti ratio variation to Pb(Zr, Ti)$O_3$ system on structural, electrical, optical and sound level characteristics in order to develope the piezoelectric and electrooptic ceramic devices. Also the specimens were prepared by the two stage sintering technique. The molecular formular was X($CaO{\cdot}1/4La_{2}O_{3}{\cdot}1/4Nb_{2}O_{5}){\cdot}(1-X)Pb(Zr_{Y}Ti_{1-Y})O_{3}$(x=100X, y=100Y), and the variation of x was $6{\sim}12$, y was 60${\sim}$49 and second stage sintering time was 20${\sim}$40 hours. The experimental results obtained from this study are as follows : 1. The density was decreased, the grain size was increased according to increase of Ca-La-Nb substitution. 2. The crystal structure was rhombohedral in composition 6/60/40, and the crystal structure was tetragonal and cubic according to increase of Ca-La-Nb substitution. 3. The Ca substitution of PZT system enhanced the sintering property. The Pb site vacancy resulting from the substitution of La-Nb increased the dielectrical constant, the piezoelectric charge constant, the dielectric loss and decreased the coercive field. 4. The resistivity of PZT system which has the P type conduction mechanism increased according to substitution of La-Nb because of the substituent acting as donor. 5. The PZT ceramics varied from ferroelectric substance according to increase of Ca-La-Nb substituent. The coercive field and saturation remanent polarization decreased, and at last straight line according to increase of La-Nb substitution. 6. The amount of Ca-La-Nb substitution to improve the light transmittance of speciment was 10 mol%, the Zr/Ti ratio was 49/51, and the second stage sintering time was 40 hours. 7. According to Ca-La-Nb substitution, the specimens was to be transparent. The 7.5/51/49 specimen was suitable for transparent sound vibrator because it had 58% light transmittance (thick 0.2[mm], wave length 700[mm]) and 48% electromechanical coupling factor.

• Electrical & Electronic Materials
• /
• v.11 no.10
• /
• pp.46-52
• /
• 1998

In this study, polarization switching characteristics of Pb(ZrxTil-x)O3 (PZT) thin films were investigated. Switching times(ts) were found to be decreased as the Zr mol% was increased. But, the switching peak currents(Imax) showed the largest value at 50 mol% Zr. As a result of this experiment, ts was found to be depended on the remanent polarization and coercive field and also Imax strongly depended on the dielectric constant of PZT thin films. In order to investigate the partial switching kinetics of PZT thin films, short and relatively small voltage pulses were applied to the MFM(metalferroelectric metal) PZT capacitors and polarization switching curves were measured with a variation of the total width of the applied pulses. Also, the switching curves were measured at different applied voltages(4, 8, 10, 12 and 14 volts). As the applied voltages increased, ts and Imax were found to be decreased and increased, respectively. In case of fatigued specimen which we applied $\pm$10 volts square pulse for 1010 cycles, ts and Imax were found to be shorter and smaller than those of virgin specimens. This is due to the decrease of the remanent polarization and the increase of the coercive field.

• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.178-183
• /
• 1995

Piezoelectric properties of sintered specimen having a tetragonal phase of $Pb_{0.9888}Sr_{0.012}(Zr_{0.52}Ti_{0.48})O_{3}$ were comparatively studied with two different poling methodes, i.e., DC field and corona discharge technique. Internal stress of poled specimens by indentation fracture toughness was analyzed to evaluate degradation phenomenon. As the results, it was confirmed that corona discharge poling technique is practicable and has merits such as low-temperature poling, slow degradation and no electric breakdown comparing to DC field poling. However, corona discharge technique showed lower Kp value than DC field poling.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1400-1401
• /
• 2006

In this study, in order to develop low temperature sintering piezoelectric ceramics for multilayer piezoelectric actuator, $PbSr(Mn_{1/3}Nb_{2/3})O_3-(Mg_{1/3}Nb_{2/3})O_3-(ZrTi)O_3$ ceramics were fabricated using $Na_{2}CO_{3}-Li_{2}CO_{3}$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the sintering tempo rature. At the sintering temperature of $900^{\circ}C$, the density, electrom echanical coupling factor(kp), mechanical quality factor(Qm) and dielectric constant(${\varepsilon}r$) of specimen showed the optimum value of $7.730[g/cm^2]$, 0.552, 1134, 1492 and 330[pC/N], respectively.

• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.3
• /
• pp.514-523
• /
• 1998

The purpose of this study was to compare the wear characteristics of Type III Gold Alloy (Degular C : Degussa AG), VMK 95 (Vita Zahnfabrik), Vitadur Alpha (Vita Zahnfabrik), IPS Empress (Ivoclar-Vivadent) and Targis (Ivoclar- Vivadent). Ten samples of each material were abraded against enamel of extracted incisors for 160,000 cycles on the wear machine. The depth of wear scars on enamel was analized with profilometer (Alpha-step 200;Tencor). And the wear of material specimen was determined with micrometer (PB-IB;Mitutoyo Co. Japan). The results obtained were as follows : 1. Type III gold alloy ($2.47{\mu}m$) and Targis ($5.89{\mu}m$) caused less wear of enamel specimens compared to VMK 95 ($75.59{\mu}m$), IPS Empress ($78.60{\mu}m$) and Vitadur Alpha ($78.89{\mu}m$) (p<0.05). 2. The wear of material specimen when opposing enamel was the lowest in type III gold alloy ($3.0{\mu}m$), followed by Targis ($69.8{\mu}m$), IPS Empress ($148.4{\mu}m$). VMK 95 ($298.0{\mu}m$) and Vitadur Alpha ($300.8{\mu}m$ exhibited the most severe wear against enamel (p<0.05).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.665-668
• /
• 1999

Thin films of Pb(Zr,Ti)O$_3$ were fabricated by means of the sol-gel spin-coating method and the multi-coating of eight coating numbers. The thin films were dried on the temperature range of 250 ~ 400($^{\circ}C$), whenever the specimens were dried after each coating Processing. The fabricated ferroelectric thin films of lead zirconate titanate(PZT) were treated with the rapid thermal annealing(RTA) at 650($^{\circ}C$),or 3(min), and direct insertion thermal annealing(DITA) at 650($^{\circ}C$), for 30(min). The measured properties of dielectric thin films were following: The good results of dielectric properties were shown by the RTA specimen. The saturation polarization(Ps), remanent polarization(Pr), coercive field (Ec), dielectric constant and dielectric loss factor of the RTA specimen were estimated to be about 27.1[ $\mu$ C/$\textrm{cm}^2$], 13.7[ $\mu$ C/$\textrm{cm}^2$], 55.6(kV/cm), 786 and 6.4(%) respectively.

• Journal of Korean Society of Water and Wastewater
• /
• v.14 no.4
• /
• pp.303-310
• /
• 2000

This study is conducted in order to find more improved solidifying effects than the former converter slag solidification technology. The converter slag is used as a solidifying agent, and the quick lime and the gypsum are used as solidifying aids. Several tests are performed for the purpose of investigating the solidifying effects and the applicability of the solidified sludge as a daily or intermediate landfill cover. The unconfined uniaxial compressive strength, pH and leaching of heavy metal are investigated. In the case of using both quick lime and gypsum as solidifying aids, the compressive strength of specimen has significantly increased that of specimen which used quick lime only. The compressive strength of each specimen cured for 7 days which is mixed with quick lime and gypsum as mixing ratios 7:1, 5:1 and 3:1 are $0.59kg/cm^2$, $1.18kg/cm^2$, and $1.25kg/cm^2$, respectively. The results of all the leaching tests of specimen cured for 7 days show that the concentrations of leachate heavy metals(Cu, Pb, Cd and $Cr^{6+}$) are lower than the Korea toxic waste criteria. The microstructure analysis by SEM shows that needlelike crystals appear as the solidification proceed. The analysis of these crystals by EDS confirms that these main components are Ca. Si etc. Also, XRD analysis shows that the main solidification products are CSH and Ettringite; in addition, $Ca(OH)_2$ CAH are observed. When the added gypsum is used as a solidifying aid, more improved solidifying effects are obtained and the solidified sludge may be appropriately used as a daily or intermediate landfill cover.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.1
• /
• pp.68-77
• /
• 2009

For the reservoir sediment highly contaminated with total Cr, Pb, and Cd, the applicability of electrokinetic remediation method was evaluated. Also, BCR sequential extraction method was adopted to compare the heavy metal speciation in between before and after electrokinetic reaction that is operated under constant current condition for the sediment. After reaction, total Cr and Pb moved toward the direction of anode, while Cd tended to cathode and stayed highest in the midst of sediment specimen. From the BCR sequential extraction analysis, it was known that for total Cr and Pb the residual fraction that showed high fraction before reaction decreased and changed to the oxidation fraction. On the other hand, for Cd the fraction of exchangeable/carbonate that dominated most fractions before reaction changed to the residual and oxidation fractions.