본 논문에서는 잡음 환경에서 효과적인 음성 인식을 위해 마스크 기반의 음성 향상 기법을 개선한다. 마스크 기반의 음성 향상 기법에서는 심층 신경망을 기반으로 추정한 마스크를 잡음 오염 음성에 곱하여 향상된 음성을 얻는다. 마스크 추정 모델로 VoiceFilter(VF) 모델을 사용하고 추정된 마스크로 얻은 음성으로부터 잔여 잡음을 보다 확실히 제거하기 위해 Spectrogram Inpainting(SI)기법을 적용한다. 본 논문에서는 음성 향상 결과를 보다 개선하기 위해 마스크 추정을 위한 모델 학습 과정에 사용되는 조합된 손실함수를 제안한다. 음성 구간에 남아 있는 잡음을 보다 효과적으로 제거하기 위해 잡음 오염 음성에 마스크를 적용한 Triplet 손실함수의 Positive 부분을 컴포넌트 손실함수와 조합하여 사용한다. 실험 평가를 위한 잡음 음성 데이터는 TIMIT 데이터베이스와 NOISEX92, 배경음악 잡음을 다양한 Signal to Noise Ratio(SNR) 조건으로 합성하여 만들어 사용한다. 음성 향상의 성능 평가는 Source to Distortion Ratio(SDR), Perceptual Evaluation of Speech Quality(PESQ), Short-Time Objective Intelligibility(STOI)를 이용한다. 실험을 통해 평균 제곱 오차로만 훈련된 기존 시스템과 비교하여, VF 모델은 평균 제곱 오차로 훈련하고 SI 모델은 조합된 손실함수를 사용하였을 때 SDR은 평균 0.5dB, PESQ는 평균 0.06, STOI는 평균 0.002만큼 성능이 향상된 것을 확인했다.
무선 네트워크의 특징들 중에 노드들은 이동성을 가지며, 제한된 대역폭과 대역폭의 변화, 높은 지연시간과 지연시간의 변화, 무선랜덤오류를 가지며 경로의 연결이 자주 단절된다. 이러한 무선 네트워크의 특징들이 무선 네트워크에서 유선 네트워크용 TCP를 사용 할 때에 성능을 떨어뜨리게 된다. 현재 무선 네트워크에 적절한 전송 프로토콜은 계속 연구 중이며, 기존에 연구된 연구 결과들은 성능이 우수하지 못하며, 특정한 환경에서만 좋은 성능을 보이기 때문에 일반적인 무선 네트워크 환경에는 적합하지 않다. 따라서 본 연구에서는 무선 네트워크에 알맞은 전송프로토콜을 연구하고 제안하기 위해 기존의 TCP 프로토콜과 이미 제안된 무선 전달계층용 프로토콜들을 분석한 뒤 성능이 더욱 우수한 무선 전달계층용 프로토콜을 제안하고자 한다. 또 다중경로를 사용하여 기존 연구가 경로의 연결이 끊기고 연결이 재설정될 때까지 전송을 할 수 없는 문제점도 해결한다. 이를 위해 TCP를 무선 환경에 적합하게 수정한 ATP(A reliable Transmission Protocol)와 TCP를 다중경로를 통해 통신을 할 수 있는 TCP-M 방식을 기반으로 ATP-M을 제안하였다. 성능이 더욱 개선되고 다중경로를 지원하는 ATP-M 프로토콜이 기존의 TCP, TCP-M, ATP보다 처리량이 우수함을 NS-2 시뮬레이션을 통해 보인다. 또한 다중경로 ATP-M에서 다중경로 개수에 따른 성능평가를 통하여 적절한 다중경로 개수를 찾는다.
정위적 방사선 수술은 한 번에 두 개내 병소에는 고선량의 방사선을 조사하면서, 주위 정상조직에는 최소한의 방사선이 조사되도록 시술하는 치료기법이다. 본 연구는 정위적 방사선 수술시 자동적 치료계획을 수행하기 위하여, 선형가속기와 감마나이프의 다수의 회전중심점을 이용하는 치료계획에 대한 물리적 격자구조에 기반한 새로운 방법을 개발하였다. 최적의 방사선 수술계획은 많은 빔관련 변수들의 조합으로서 만들어진다. 본 연구에서는 선형가속기와 감마나이프 수술시 빔 측면도의 50% 수준에서의 선량분포가 콜리메이터/헬멧의 구멍 크기와 일치하는 점을 이용하여 하나의 회전중심점을 중심으로 선량분포를 구형으로 모델화시켰다. 그리고, 다수의 회전중심점들은 병소내 위치와 크기를 고려한 정육면체 구조와 1×1×1 ㎣의 체적소 단위의 계산에 의해 자동적으로 배치시켰다. 이 기법에 의한 치료계획 방법은 선량체적히스토그램, 선량의 일치성, 선량의 균질성의 병소내 선량분포로서 평가되었다. 그 결과, 새로운 기법은 불규칙한 병소들에 대하여 프로그램 시스템에 의해 빠르게 다수의 회전중심점들을 배치시켰다. 또한, RTOG의 권고사항에 언급된 병소내 선량분포의 일치성, 균질성이 기준을 잘 만족하였고, 병소들은 50% 이상의 등선량 곡선 내에 포함되었다. 이와 같은 성과는 불규칙하게 형성된 병소와 선형가속기나 감마나이프와 같은 다른 치료 장치 기법들에서 특별한 제약없이 보편적으로 적용이 될 수 있을 것으로 생각된다.
본 연구에서는 기상조건에 영향을 받지 않고 레이더산란 측정을 할 수 있는 X-band 안테나 기반 자동관측 시스템을 구축하였다. 이 시스템을 이용하여 벼 생육시기에 따른 편파별 후방산란계수 변화와 벼 생육인자 변화를 관측하고, 후방산란계수와 벼 생육인자와의 관계를 분석을 통해 최적조건의 후방산란계수를 이용한 벼 생육을 추정하였다. 벼 생육시기에 후방산란계수 변화를 관측해 본 결과 생육초기에는 VV-편파가 HH, HV/VH-편파 보다 후방산란계수가 높게 나타났고, 모든 편파별 후방산란계수가 벼 유수형성기 (7월 말경)까지 증가하다가 그 후 감소 한 후 9월 초순이후 다시 증가하는 dual-peak 현상을 뚜렷이 나타났다. 동시에 생육시기에 따른 생체중, 이삭 건물중, 엽면적지수, 초장 등 벼 생육인자들의 생육 변화를 관측해 보았는데 생체중, 엽면적지수, 초장은 6월 중순부터 7월 하순까지 편파별 후방산란계수와의 변화 경향이 비슷하게 나타났고, 이삭 건물중의 경우 특히 VV-편파 후방산란계수가 9월 초순에서 10월 초순까지 변화 경향이 동일하게 나타났다. 편파별 후방산란계수와 벼 생육인자와의 상관관계를 분석한 결과 엽면적지수, 생체중은 6월 중순 (DOY 168)부터 7월 하순 (DOY 209) 시기에 HH-편파 후방산란 계수와 상관관계가 높았고, 초장은 같은 시기에 VV-편파 후방산란계수와 관계가 높게 나타났다. 이삭 건물중의 경우 벼 출수기가 끝나고 결실기로 접어드는 9월 초순 (DOY 244) 부터 10월 초순 (DOY 276) 시기에 VV-편파 후방산란계수와 상관관계가 높게 나타났다. 이 결과를 바탕으로 벼 생육인자와 상관이 높게 나타난 편파별 후방산란계수를 이용하여 벼 생육을 추정하였다. 엽면적지수는 HH-편파 후방산란계수를 이용하여 2007년도 실측값과 2008년도 추정 경험 모형을 비교해본 결과 비교적 오차가 작았고 (RMSE=0.43), 상관관계가 높은 HH-편파 후방산란계수를 이용하여 2007년도 생체중 실측값과 생체중 추정 모형 (2008년도)을 비교해 본 결과 RMSE가 41.0 g $m^{-2}$ 으로 비교적 작은 오차를 보여 생체중 추정 모형의 유효성이 높다는 것이 증명되었다. 또한 초장의 경우 실측값 (2007년)과 초장 추정 모형 (2008년)을 비교 분석한 결과 오차 범위가 비교적 작게 나타났고 (RMSE=6.93 cm), VV-편파 후방산란계수를 이용해 얻은 이삭 건물중 추정 경험 모형 (2008년도)과 2007년도 이삭 건물중 실측값과의 관계를 통해 추정식을 검증한 결과 RMSE=0.35 g/m2 을 보여 이삭 건물중 추정모형의 유효성이 높다는 것이 증명되었다. 본 연구결과에서는 Kim et al. (2009)이 일정한 간격을 두고 수동조건으로 관측한 결과와 비교해서 벼 생육시기에 따른 편파별 후방산란계수 변화 경향이 뚜렷하게 나타났고, 이 후방산란계수를 이용하여 벼 생육인자와의 관계 및 추정 결과에서도 기존 결과보다 상관관계 및 생육추정 모형 유효성이 높게 나타났다. 본 연구 결과를 통해 X-band 산란계 자동측정 시스템을 이용하여 벼 생육을 예측 할 수 있음을 확인하였다.
방사선치료계획시스템의 MU계산 결과를 포괄적이고 독립적으로 검증할 수 있고 빔데이터 관리를 위한 사용자 친화적인 프로그램을 개발하였다. 선량계산의 정확성을 향상시키기 위해서 축이탈 인자, 빔 경화효과, 비균질성 보정 등의 요소를 계산 알고리듬에 포함하였고 상시적 정도관리 결과로 측정된 빔데이터로의 경신이 용이하도록 하였다. 기준깊이, SSD 등의 측정조건이 다를 때에 보정하는 알고리듬을 구현하였다. 상용 스프레드시트의 워크시트 함수를 빔데이터베이스 접근에 사용하였고, Visual Basic for Application (VBA) 개발환경을 사용하여 graphic user interface (GUI)를 구현하였다. 프로그램의 정확도를 평가하기 위하여 동일한 빔 데이터를 가진 치료계획 시스템을 이용하여 213개의 경우에 대한 팬톰의 선량을 계산하고 비교하였다. 또한 3차원 입체조형방사선 치료를 받은 17명의 환자데이터로부터 108개의 MU계산 기록을 추출하여 본 프로그램에서 계산된 MU와 비교하였다. 가상의 팬톰을 대상으로 계산을 수행한 결과, 과도한 비균질 영역계산을 제외하면 계산된 MU가 치료계획시스템과 3% 이내에서 잘 일치하였고, 환자 데이터를 이용한 계산에서도 과도한 비균질 영역 계산을 제외한 모든 계산에서 최대오차가 5% 이하로 나타났다. VBA 및 Microsoft Excel 워크시트 인터페이스를 이용하여 임상에 이용될 빔데이터 자료의 자동 생성 및 빔데이터 비교 템플릿 등의 용이성이 판명되었다. 본 프로그램을 이용하여 치료계획시스템의 정확성을 포괄적으로 검증할 수 있으므로 치료계획시스템의 정도관리 및 환자의 독립적 선량검증을 효과적으로 수행할 수 있다. 빔데이터베이스 생성 기능을 이용하여 빔데이터의 주기적 관리 경신 및 대단위 빔데이터베이스의 모니터링을 효율적으로 수행할 수 있다.
최근 스마트폰의 등장으로 인해 사용자들은 시간과 공간의 제약 없이 스마트폰을 이용한 새로운 의사소통의 방법을 경험하고 있다. 이러한 스마트폰은 고화질의 컬러화면, 고해상도 카메라, 실시간 3D 가속그래픽과 다양한 센서(GPS와 Digital Compass) 등을 제공하고 있으며, 다양한 센서들은 사용자들(개발자, 일반 사용자)로 하여금 이전에 경험하지 못했던 서비스를 경험할 수 있도록 지원하고 있다. 그 중에서 모바일 증강현실은 스마트폰의 다양한 센서들을 이용하여 개발할 수 있는 대표적인 서비스 중 하나이며, 이러한 센서들을 이용한 다양한 방법의 모바일 증강현실 연구들이 활발하게 진행되고 있다. 모바일 증강현실은 크게 위치 정보 기반의 서비스와 내용 기반 서비스로 구분할 수 있다. 위치 정보 기반의 서비스는 구현이 쉬운 장점이 있으나, 증강되는 정보의 위치가 실제의 객체의 정확한 위치에 증강되는 정보가 제공되지 않는 경우가 발생하는 단점이 존재한다. 이와 반대로, 내용 기반 서비스는 정확한 위치에 증강되는 정보를 제공할 수 있으나, 구현 및 데이터베이스에 존재하는 이미지의 양에 따른 검색 속도가 증가하는 단점이 존재한다. 본 논문에서는 위치 정보 기반의 서비스와 내용기반의 서비스의 장점들을 이용한 방법으로, 스마트폰의 다양한 센서(GPS, Digital Compass)로 부터 수집된 정보를 이용하여 데이터베이스의 탐색 범위를 줄이고, 탐색 범위에 존재하는 이미지들의 특징 정보를 기반으로 실제의 랜드마크를 인식하고, 인식한 랜드마크의 정보를 링크드 오픈 데이터(LOD)에서 검색하여 해당 정보를 제공하는 랜드마크 가이드 시스템을 제안한다. 제안하는 시스템은 크게 2개의 모듈(랜드마크 탐색 모듈과 어노테이션 모듈)로 구성되어있다. 첫 번째로, 랜드마크 탐색 모듈은 스마트폰으로 인식한 랜드마크(건물, 조형물 등)에 해당하는 정보들을 (텍스트, 사진, 비디오 등) 링크드 오픈 데이터에서 검색하여 검색된 결과를 인식한 랜드마크의 정확한 위치에 정보를 제공하는 역할을 한다. 스마트폰으로부터 입력 받은 이미지에서 특징점 추출을 위한 방법으로는 SURF 알고리즘을 사용했다. 또한 실시간성을 보장하고 처리 속도를 향상 시키기 위한 방법으로는 입력 받은 이미지와 데이터베이스에 있는 이미지의 비교 연산을 수행할 때 GPS와 Digital Compass의 정보를 사용하여 그리드 기반의 클러스터링을 생성하여 탐색 범위를 줄임으로써, 이미지 검색 속도를 향상 시킬 수 있는 방법을 제시하였다. 두 번째로 어노테이션 모듈은 사용자들의 참여에 의해서 새로운 랜드마크의 정보를 링크드 오픈 데이터에 추가할 수 있는 기능을 제공한다. 사용자들은 키워드를 이용해서 링크드 오픈 데이터로에서 관련된 주제를 검색할 수 있으며, 검색된 정보를 수정하거나, 사용자가 지정한 랜드마크에 해당 정보를 표시할 수 있도록 지정할 수 있다. 또한, 사용자가 지정하려고 하는 랜드마크에 대한 정보가 존재하지 않는다면, 사용자는 랜드마크의 사진을 업로드하고, 새로운 랜드마크에 대한 정보를 생성하는 기능을 제공한다. 이러한 과정은 시스템이 카메라로부터 입력 받은 대상(랜드마크)에 대한 정확한 증강현실 컨텐츠를 제공하기 위해 필요한 URI를 찾는데 사용되며, 다양한 각도의 랜드마크 사진들을 사용자들에 의해 협업적으로 생성할 수 있는 환경을 제공한다. 본 연구에서 데이터베이스의 탐색 범위를 줄이기 위해서 랜드마크의 GPS 좌표와 Digital Compass의 정보를 이용하여 그리드 기반의 클러스터링 방법을 제안하여, 그 결과 탐색시간이 기존에는 70~80ms 걸리는 반면 제안하는 방법을 통해서는 18~20ms로 약 75% 정도 향상된 것을 확인할 수 있었다. 이러한 탐색시간의 감소는 전체적인 검색시간을 기존의 490~540ms에서 438~480ms로 약 10% 정도 향상된 것을 확인하였다.
한국퍼지및지능시스템학회 1993년도 Fifth International Fuzzy Systems Association World Congress 93
/
pp.975-976
/
1993
This talk presents the overview of the author's research and development activities on fuzzy inference hardware. We involved it with two distinct approaches. The first approach is to use application specific integrated circuits (ASIC) technology. The fuzzy inference method is directly implemented in silicon. The second approach, which is in its preliminary stage, is to use more conventional microprocessor architecture. Here, we use a quantitative technique used by designer of reduced instruction set computer (RISC) to modify an architecture of a microprocessor. In the ASIC approach, we implemented the most widely used fuzzy inference mechanism directly on silicon. The mechanism is beaded on a max-min compositional rule of inference, and Mandami's method of fuzzy implication. The two VLSI fuzzy inference chips are designed, fabricated, and fully tested. Both used a full-custom CMOS technology. The second and more claborate chip was designed at the University of North Carolina(U C) in cooperation with MCNC. Both VLSI chips had muliple datapaths for rule digital fuzzy inference chips had multiple datapaths for rule evaluation, and they executed multiple fuzzy if-then rules in parallel. The AT & T chip is the first digital fuzzy inference chip in the world. It ran with a 20 MHz clock cycle and achieved an approximately 80.000 Fuzzy Logical inferences Per Second (FLIPS). It stored and executed 16 fuzzy if-then rules. Since it was designed as a proof of concept prototype chip, it had minimal amount of peripheral logic for system integration. UNC/MCNC chip consists of 688,131 transistors of which 476,160 are used for RAM memory. It ran with a 10 MHz clock cycle. The chip has a 3-staged pipeline and initiates a computation of new inference every 64 cycle. This chip achieved an approximately 160,000 FLIPS. The new architecture have the following important improvements from the AT & T chip: Programmable rule set memory (RAM). On-chip fuzzification operation by a table lookup method. On-chip defuzzification operation by a centroid method. Reconfigurable architecture for processing two rule formats. RAM/datapath redundancy for higher yield It can store and execute 51 if-then rule of the following format: IF A and B and C and D Then Do E, and Then Do F. With this format, the chip takes four inputs and produces two outputs. By software reconfiguration, it can store and execute 102 if-then rules of the following simpler format using the same datapath: IF A and B Then Do E. With this format the chip takes two inputs and produces one outputs. We have built two VME-bus board systems based on this chip for Oak Ridge National Laboratory (ORNL). The board is now installed in a robot at ORNL. Researchers uses this board for experiment in autonomous robot navigation. The Fuzzy Logic system board places the Fuzzy chip into a VMEbus environment. High level C language functions hide the operational details of the board from the applications programme . The programmer treats rule memories and fuzzification function memories as local structures passed as parameters to the C functions. ASIC fuzzy inference hardware is extremely fast, but they are limited in generality. Many aspects of the design are limited or fixed. We have proposed to designing a are limited or fixed. We have proposed to designing a fuzzy information processor as an application specific processor using a quantitative approach. The quantitative approach was developed by RISC designers. In effect, we are interested in evaluating the effectiveness of a specialized RISC processor for fuzzy information processing. As the first step, we measured the possible speed-up of a fuzzy inference program based on if-then rules by an introduction of specialized instructions, i.e., min and max instructions. The minimum and maximum operations are heavily used in fuzzy logic applications as fuzzy intersection and union. We performed measurements using a MIPS R3000 as a base micropro essor. The initial result is encouraging. We can achieve as high as a 2.5 increase in inference speed if the R3000 had min and max instructions. Also, they are useful for speeding up other fuzzy operations such as bounded product and bounded sum. The embedded processor's main task is to control some device or process. It usually runs a single or a embedded processer to create an embedded processor for fuzzy control is very effective. Table I shows the measured speed of the inference by a MIPS R3000 microprocessor, a fictitious MIPS R3000 microprocessor with min and max instructions, and a UNC/MCNC ASIC fuzzy inference chip. The software that used on microprocessors is a simulator of the ASIC chip. The first row is the computation time in seconds of 6000 inferences using 51 rules where each fuzzy set is represented by an array of 64 elements. The second row is the time required to perform a single inference. The last row is the fuzzy logical inferences per second (FLIPS) measured for ach device. There is a large gap in run time between the ASIC and software approaches even if we resort to a specialized fuzzy microprocessor. As for design time and cost, these two approaches represent two extremes. An ASIC approach is extremely expensive. It is, therefore, an important research topic to design a specialized computing architecture for fuzzy applications that falls between these two extremes both in run time and design time/cost. TABLEI INFERENCE TIME BY 51 RULES {{{{Time }}{{MIPS R3000 }}{{ASIC }}{{Regular }}{{With min/mix }}{{6000 inference 1 inference FLIPS }}{{125s 20.8ms 48 }}{{49s 8.2ms 122 }}{{0.0038s 6.4㎲ 156,250 }} }}
A 1,989-bp genomic region encoding nickel resistance genes was isolated from Legionella pneumophila, a pathogen for legionellosis. From a sequencing and computer analysis, the region was found to harbor two structural genes, a nreB-like protein gene (1,149 bp) and a nreA-like protein gene (270 bp), in a row. Both genes exhibited a significant degree of similarity to the corresponding genes from Synechocystis sp. PCC6803 ($54\%$ amino acid sequence identity) and Achromobacter xylosoxidans 31A ($76\%$). The gene was successfully expressed in E. coli MG1655 and conferred a nickel resistance of up to 5 mM in an LB medium and 3 mM in a TMS medium including gluconate as the sole carbon source. E. coli harboring the nickel resistance gene also exhibited a substantial resistance to cobalt, yet no resistance to cadmium or zinc. Since the extracellular concentration of nickel remained constant during the whole period of cultivation, it was confirmed that the nickel resistance was provided by an efflux system like the $Ni^2+$permease (nrsD) of Synechocystis sp. strain PCC6803. Since polyphosphate (poly-P) is known as a global regulator for gene expression as well as a potential virulence factor in E. coli, the nickel resistance of a ppk mutant of E. coli MG 1655 harboring the nickel resistance gene from L. pneumophila was compared with that of its parental strain. The nickel resistance was significantly attenuated by ppk inactivation, which was more pronounced in an LB medium than in a TMS medium.
Oral implants must fulfill certain criteria arising from special demands of function, which include biocompatibility, adequate mechanical strength, optimum soft and hard tissue integration, and transmission of functional forces to bone within physiological limits. And one of the critical elements influencing the long-term uncompromise functioning of oral implants is load distribution at the implant- bone interface, Factors that affect the load transfer at the bone-implant interface include the type of loading, material properties of the implant and prosthesis, implant geometry, surface structure, quality and quantity of the surrounding bone, and nature of the bone-implant interface. To understand the biomechanical behavior of dental implants, validation of stress and strain measurements is required. The finite element analysis (FEA) has been applied to the dental implant field to predict stress distribution patterns in the implant-bone interface by comparison of various implant designs. This method offers the advantage of solving complex structural problems by dividing them into smaller and simpler interrelated sections by using mathematical techniques. The purpose of this study was to evaluate the stresses induced around the implants in bone using FEA, A 3D FEA computer software (SOLIDWORKS 2004, DASSO SYSTEM, France) was used for the analysis of clinical simulations. Two types (external and internal) of implants of 4.1 mm diameter, 12.0 mm length were buried in 4 types of bone modeled. Vertical and oblique forces of lOON were applied on the center of the abutment, and the values of von Mises equivalent stress at the implant-bone interface were computed. The results showed that von Mises stresses at the marginal. bone were higher under oblique load than under vertical load, and the stresses were higher at the lingual marginal bone than at the buccal marginal bone under oblique load. Under vertical and oblique load, the stress in type I, II, III bone was found to be the highest at the marginal bone and the lowest at the bone around apical portions of implant. Higher stresses occurred at the top of the crestal region and lower stresses occurred near the tip of the implant with greater thickness of the cortical shell while high stresses surrounded the fixture apex for type N. The stresses in the crestal region were higher in Model 2 than in Model 1, the stresses near the tip of the implant were higher in Model 1 than Model 2, and Model 2 showed more effective stress distribution than Model.
우리나라 3대 수면 질환으로는 코골이, 수면무호흡증, 불면증이 있다. 수면 부족은 만병의 근원이며 수면 부족으로 인한 질병은 심혈관계 질환, 인지장애, 비만, 당뇨, 대장염, 전립선암에 이르기까지 다양하게 나타난다. 수면 관리 중요성을 인식한 정부도 2018년 7월부터 수면다원검사를 국민건강보험 혜택을 적용해서 작은 부담으로 검사를 받아볼 수 있도록 하고 있다. 그럼에도 불구하고 불면증 환자는 시간적·공간적·경제적 부담감을 해소하고 일상생활 속에서 수면의 질을 관리할 필요가 있다. 이러한 문제를 해결하기 위해서 본 논문에서는 병원이 아닌 일상생활 속에서 수면관리에 활용할 수 있는 안대형 생체신호 측정기기를 개발하였다. 측정기기에서는 6개 생체신호(안구동작, 뒤척임, 체온, 산소포화도, 심박수, 오디오)를 측정할 수 있다. 사용되는 센서로는 안구동작, 뒤척임은 자이로스코프센서(MPU9250, InvenSense, 미국)가 사용되었다. 센서값 입력 범위는 258~460°/sec 단위로 조정되며, 입력 범위값 내에서 작동상태를 확인하였다. 체온, 산소포화도, 심박수는 센서(MAX30102, Analog Devices, 미국)를 사용하였다. 체온은 30~45℃ 작동상태를 확인했으며, 산소포화도 사용범위는 미사용상태는 0%이고 사용상태는 20~90%의 작동상태를 확인하였다. 심박수의 범위는 40~180 bpm에서 작동상태를 확인하였다. 오디오 신호는 센서(AMM2742-T-R, PUIaudio, 미국)를 통해서 생체신호를 측정하며 감도는 -42±1 dB이며 주파수 범위는 20~20 kHz에서의 작동상태를 확인하였다. 시스템 구성은 생체신호 측정기기와 데이터수집 장치로 PC 및 모바일 애플리케이션으로 구성되었다. 측정된 데이터는 모바일과 PC로 수집되며 수집된 데이터는 수면의 단계를 판단하고 수면 유도와 수면장애에 대한 사전 선별기능을 진행할 수 있는 기초자료로 사용될 수 있다. 앞으로 간편하게 가정에서 불면증 환자들에게 수면의 질을 측정할 수 있게 되어 불면증 환자들의 치료에 도움이 될 것으로 예상한다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.