• Coupled systems mechanics
• /
• v.7 no.5
• /
• pp.509-524
• /
• 2018

A hierarchical multi-scale modeling strategy devoted to the study of a Bitumen-Bound Gravel (BBG) is presented in this paper. More precisely, the paper investigates the temperature-dependent linear viscoelastic of the material when submitted to low deformations levels and moderate number of cycles. In such a hierarchical approach, 3D digital Representative Elementary Volumes are built and the outcomes at a scale (here, the sub-mesoscale) are used as input data at the next higher scale (here, the mesoscale). The viscoelastic behavior of the bituminous phases at each scale is taken into account by means of a generalized Maxwell model: the bulk part of the behavior is separated from the deviatoric one and bulk and shear moduli are expanded into Prony series. Furthermore, the viscoelastic phases are considered to be thermorheologically simple: time and temperature are not independent. This behavior is reproduced by the Williams-Landel-Ferry law. By means of the FE simulations of stress relaxation tests, the parameters of the various features of this temperature-dependent viscoelastic behavior are identified.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.11 s.116
• /
• pp.1124-1131
• /
• 2006

This paper presents a novel method to determine sound power level(PWL) emitted by a travelling vehicle for road traffic noise simulation. The PWL is evaluated by the equivalent sound pressure level (SPL) measured by close proximity method and the sound power correction factor derived from the maximum SPL measured by pass-by method and the propagation attenuation of vehicle noise during the pass-by measurement. Using the method, we derive the empirical formula for PWL estimation in 1/1-octave and overall frequency bands for 8 vehicles (automobile, SUV, small truck, large bus, trailer, 3 dump trucks) tested at two road surfaces (dense graded asphalt, 30mm transverse tinning concrete) of Korean highway test road. The suggested approach, if securing sufficient data to represent the acoustic characteristics of all vehicle types, has il strong merit to be able to evaluate sound power levels for any combination of vehicle categories and traffic volumes.

• The Journal of Korean Medicine
• /
• v.29 no.4
• /
• pp.213-217
• /
• 2008

Since at least the late 12th century, medical herbs grown naturally or cultivated in Korea have been referred to as 'HyangYak'(鄕藥, $Xi\bar{a}ngY\grave{a}o$). Herbs from other countries are referred to as 'DangYak'(唐藥, $D\bar{a}ngY\grave{a}o$). Some senior historians claim medicines made solely from HyangYak are purely Korean, since they originated and were developed fully within Korea. However, these localized medicines became abundant as the result of exchanges between Korea and other countries. Originally published in 1433, 'HyangYakJipSungBang' is the authoritative result of earlier writings of medical books using HyangYak. Comprised of a total of 85 volumes, it was large in scale and divided into three main sections: 1) a detailed description of the 703 kinds of HyangYak, 2) explanations of the 10,706 different herbal formulae and 959 types of symptoms or diseases, and 3) descriptions of the 1,416 various acupuncture and moxibustion formulae. It's noted that 'HyangYakJipSungBang' was not written all at once. In the process of its writing, the number of formulae increased through medical exchanges between Korea and China during the 15th century.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2235-2245
• /
• 2000

The necessity of using rapid prototyping(RP) for short-run manufacturing is continuously driving a development of a cost-effective technique that will produce completely-finished quality parts in a very short time. To meet these demands, the improvements in production speed, accuracy, materials, aid cost are crucial. Thus, a new hybrid-RP system performing both deposition and machining in a station is proposed. For the new hybrid RP process to maintain the same degree of process automation as in currently available processes like SLA or FDNI, a sophisticated process planning system is developed. In the process planner, CAD models(STEP AP203) are partitioned into 3D manufacturable volumes called 'Ueposition feature segment"(DFS) after machining features called "machining feature segmenf'(MFS) are extracted from the initial CAD model. Once MFS and DFS are identified, the process planner arranges them into a chain of processes and automatically generates machining information for each DFS and MFS. The goal of this paper is to present a framework for a process planning system for hybrid RP processes and to outline the geometric algorithms involved in developing such an environment.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.4
• /
• pp.318-326
• /
• 1999

Recently, electronic systems including computers have been rapidly shrinking in size while at the same time the complexity and the capability of these systems continue to grow/sup [1]/. Thus, system volumes have decreased as system power has increased, resulting in dramatic increases in system heat density. The high temperature of the computer system is considered as the major reason for low performance and shortening life of the product. It is necessary to solve this problem due to the heat density increased and to develop the design skill of the computer cabinet according to miniaturization. M4500 desk-top computer was selected for analyzing the thermal management inside cabinet. The cabinet volume, the configuration of the heating devices, the size and location of air ventilation, and the fan selection have been investigated as the important parameters to find out an optimal cabinet design. The objectives of this project were to analyze which design parameters would affect cooling performance by thermal strategy, to design an optimal model, and to measure the temperatures of the main parts to confirm the effect of the thermal design. The temperatures of each part of the optimal model were compared with those of the existing model. As a result. the volume of this miniaturized model was about 16% smaller than that of M4500 without any change in operating performance.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3749-3754
• /
• 2012

Nanoporous carbons with a high specific surface area were prepared directly from thermoplastic acrylic resin as carbon precursor and MgO powder as template by carbonization over the temperature range, $500-1000^{\circ}C$. The effect of the carbonization temperature on the pore structure and $CO_2$ adsorption capacity of the obtained porous carbon was examined. The textural properties and morphology of the porous carbon materials were analyzed by $N_2/-196^{\circ}C$ and $CO_2/0^{\circ}C$ adsorption/desorption isotherms, SEM and TEM. The $CO_2$ adsorption capacity of the prepared porous carbon was measured at $25^{\circ}C$ and 1 bar and 30 bar. The specific surface area increased from 237 to $1251m^2/g$, and the total pore volumes increased from 0.242 to $0.763cm^3/g$ with increasing the carbonization temperature. The carbonization temperature acts mainly by generating large narrow micropores and mesopores with an average pore size dependent on the level of carbonization of the MgO-templated nanoporous carbons. The results showed that the MgO-templated nanoporous carbons at $900^{\circ}C$ exhibited the best $CO_2$ adsorption value of 194 mg/g at 1 bar.

• The Journal of the Society of Korean Medicine Diagnostics
• /
• v.9 no.2
• /
• pp.57-71
• /
• 2005

Background and purpose: Maek Kyoung(脈經) is a book written, compiled, and edited by Wang Hui circa 3 A.D. This book is the first technical book devoted to the diagnostics. These are very important data but never make a special study and translate. so I hope this treatise can be great help to understand diagnosis study. Methods: Maek Kyoung(脈經) consists of ten volumes, and the third volume consists of the five chapters, including inter-generation and inter-restriction of the five viscera and the six entrails and prognosis of diseases. This treatise is made up of principal, notes, study and conclusion, we tried to make a translation faithful to the original. Results and Conclusion: Chapter 5 refers to three things. The first is relation between kidney and urinary bladder, the second is ordinary and extraordinary pulse condition of kidney, and the third is how to treat diseases related to kidney.

• Economic and Environmental Geology
• /
• v.45 no.1
• /
• pp.41-48
• /
• 2012

A theoretical $CO_2$ storage capacity is estimated on the southwestern continental shelf margin of Ulleung Basin, offshore Korea using 2D/3D multi-channel seismic and wellbore data acquired in the area over the two decades since the late 1980s. For the first time in Korea, the present study applies an efficiency factor to the capacity calculation, together with the other required parameters. For possible $CO_2$ storage volume estimation of the study area, we interpreted the seismic data in the Gorae area from 800 m to 3,000 m below the seafloor integrated with the well data, and identified five different seismic units; the limited depth interval is considered because of fluid state of $CO_2$ and tightness of the formation. The total volumes of each seismic unit were converted with a time-depth relation inferred from the checkshot surveys before the other required parameters including porosity and density were applied to compute the potential storage capacity. The accumulated possible storage volume from the five depositional units in the study area is estimated to be approximately 5,100 Mton ($P_{50}$). The approaches made in this study will be applied to the rest area of the basin and other continental shelves (i.e., Yellow Sea and northern part of East China Sea) in the next phase.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.681-689
• /
• 2023

Purpose: Muons are characterized by a strong penetrating ability and can travel through thousands of meters of rock, making them ideal to image large volumes and substances typically impenetrable to, for example, electrons and photons. The feasibility of 3D image reconstruction and material identification based on a cosmic ray muons tomography (MT) system with triangular bar plastic scintillator detectors has been verified in this paper. Our prototype shows potential application value and the authors wish to apply this prototype system to 3D imaging. In addition, an MT experiment with the same detector system is also in progress. Methods: A simulation based on GEANT4 was developed to study cosmic ray muons' physical processes and motion trails. The yield and transportation of optical photons scintillated in each triangular bar of the detector system were reproduced. An image reconstruction algorithm and correction method based on muon scattering, which differs from the conventional PoCA algorithm, has been developed based on simulation data and verified by experimental data. Results: According to the simulation result, the detector system's position resolution is below 1 ~ mm in simulation and 2 mm in the experiment. A relatively legible 3D image of lead bricks in size of 20 cm × 5 cm × 10 cm used our inversion algorithm can be presented below 1× 10⁴ effective events, which takes 16 h of acquisition time experimentally. Conclusion: The proposed method is a potential candidate to monitor the cosmic ray MT accurately. Monte Carlo simulations have been performed to discuss the application of the detector and the simulation results have indicated that the detector can be used in cosmic ray MT. The cosmic ray MT experiment is currently underway. Furthermore, the proposal also has the potential to scan the earth, buildings, and other structures of interest including for instance computerized imaging in an archaeological framework.

• Imaging Science in Dentistry
• /
• v.43 no.3
• /
• pp.135-143
• /
• 2013

Purpose: This study was performed to obtain a quantitative evaluation of the cortical and cancellous bone graft harvestable from the mental and canine regions, and to evaluate the cortical vestibular thickness. Materials and Methods: This study collected cone-beam computed tomographic (CBCT) images of 100 Italian patients. The limits of the mental region were established: 5 mm in front of the medial margin of each mental foramen, 5 mm under the apex of each tooth present, and above the inferior mandibular cortex. Cortical and cancellous bone volumes were evaluated using SimPlant software (SimPlant 3-D Pro, Materialize, Leuven, Belgium) tools. In addition, the cortical vestibular thickness (minimal and maximal values) was evaluated in 3 cross-sections corresponding to the right canine tooth (3R), the median section (M), and the left canine tooth (3L). Results: The cortical volume was $0.71{\pm}0.23mL$ (0.27-1.96 mL) and the cancellous volume was $2.16{\pm}0.76mL$ (0.86-6.28 mL). The minimal cortical vestibular thickness was $1.54{\pm}0.41mm$ (0.61-3.25 mm), and the maximal cortical vestibular thickness was $3.14{\pm}0.75mm$ (1.01-5.83 mm). Conclusion: The use of the imaging software allowed a patient-specific assessment of mental and canine region bone availability. The proposed evaluation method might help the surgeon in the selection of the donor site by the comparison between bone availability in the donor site and the reconstructive exigency of the recipient site.