• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.369-374
• /
• 2011

An induction motor operated with high voltage source generally generates high current in starting mode and has a long transient time after being started. This large and sustaining starting current causes the end windings of the stator to have excessive electromagnetic force. This force is the source of vibration and has a negative and serious influence on the insulation of end windings. Therefore, designing the end winding part with an appropriate support system is needed. To design the support ring enclosing the end windings, we analyze the distribution of electromagnetic force on the end windings by applying the Biot-Savart's law and the 3D finite element method (FEM), and comparing two simulation methods. Finally, we verify the safety of the support structure of the end winding part using stress analysis, which is analyzed with the electromagnetic forces from the 3D FEM simulation.

• Progress in Superconductivity and Cryogenics
• /
• 제21권3호
• /
• pp.32-37
• /
• 2019

In various types of large-scale electrical applications, the number of coil turns in such machines is usually large. Electromagnetic simulation of large-scale superconducting coils (tens to hundreds of turns) is indispensable in the design process of superconducting electrical equipment. However, due to the large scale of the coil and the large aspect ratio of super-conducting material layer in HTS coated conductor, it is usually difficult or even unable to perform 3-D transient electromagnetic simulation. This paper introduces an effective 3-D electromagnetic simulation method for large-scale HTS coated conductor coil based on T-A formulation. The simulation and experimental results show that the 3-D model based on the T-A formulation using homogeneous strategy is more accurate than the traditional 2-D models. The memory usage is not sensitive to the number of turns and this model will be even more superior as the number of turns becomes larger.

• Transactions of Materials Processing
• /
• 제28권3호
• /
• pp.159-166
• /
• 2019

Electromagnetic forming (EMF) simulations consider 3-dimensionally coupled electromagnetic-mechanical phenomenon using LS-DYNA, therefore the calculation cost is normally expensive. In this study, a sensitivity analysis in regard to the simulation variables affecting the calculation time was carried out. The EMF experiments were conducted to form an elliptically protruding shape on a high-strength steel sheet, and it was predicted using LS-DYNA simulation. In this particular EMF simulation case, the effect of several simulation variables, viz., element size, contact condition, EM-time step interval, and re-calculation number of the EM matrices, on the shape of elliptical protrusion and the total calculation time was analyzed. As a result, reasonable values of the simulation variables between the simulation precision and calculation time were proposed, and the EMF experiments with respect to the charging voltages were successfully predicted.

• Journal of Internet Computing and Services
• /
• 제23권3호
• /
• pp.67-76
• /
• 2022

Power and signal transmission using electromagnetic waves are essential in modern times, and a guided structure is needed to transmit electromagnetic waves efficiently through the desired path. This paper performed an electromagnetic simulation using the in-house code for the 2-D/3-D waveguide using the finite element method. The accuracy of the analysis was verified by comparing it with the results of HFSS, a representative electromagnetic wave simulation software. In addition, the performance of the Absorbing Boundary Condition (ABC), which is essential to truncate the infinite computational domain for computational electromagnetics, was analyzed. Finally, the parallelization technique was applied to accelerate the simulation speed, demonstrating performance improvement.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1957-1959
• /
• 2004

In this paper, maxwell 3D finite element analysis program was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 2.56[MHz] and some specific conditions.

• Journal of electromagnetic engineering and science
• /
• 제7권4호
• /
• pp.175-182
• /
• 2007

In this paper, a study on the reflector type frequency doubler, to suppress the undesired harmonics, is presented. A 12 to 24 GHz reflective frequency doubler is simulated and experimented. Design procedure of the frequency doubler with reflector is provided and the frequency doubler with good spectral purity is fabricated successfully. It has harmonic suppression of the $40{\sim}50\;dBc$ in the $1^{st}$ harmonic and the $50{\sim}60\;dB$ in the $3^{rd}$ harmonic with no additional filter. And, it has conversion gain with the input power of 0 dBm over bandwidth of 500 MHz. A NEC's ne71300(N) GaAs FET is used and the nonlinear model(EEFET3) using IC-CAP program is extracted for harmonic load pull simulation. Good agreement between simulated and measured results has been achieved.

• Journal of electromagnetic engineering and science
• /
• 제13권4호
• /
• pp.263-266
• /
• 2013

A novel compact and low-loss VHF bandpass filter is presented with enhanced stopband performance using metamaterial zeroth order resonator (ZOR) characteristics. An in-line ZOR filter is initially suggested and changed to have transmission zeros (TZs) due to source-load coupling for effective improvement of the isolation from UHF wireless channels. The proposed filter is smaller than 1/10 of the conventional filters in terms of size and has relatively very low insertion loss (< 1 dB for the electromagnetic (EM) simulation and < 3 dB for the measurement) and return loss (<-20 dB) in the passband due to the approximately 80% size reduction and the higher isolation in the stopband due to the TZs. The circuit and EM simulation are in good agreement with the measurements.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.225-228
• /
• 2000

In this paper, the design for a low noise amplifier with the EM simulation is presented. The ATF36077 pHEMT device is applied to design LNA for U-NII frequency band (5 GHz ～ 6 GHz). The matching networks have been designed by the only open ended stub in order to reduce parasitic effects generated from a via structure. Through EM simulator, the simulation result shows that the linear gain (@5.5 GHz) is over 10 dB, input return loss and output return loss (@ 5.5 GHz) are a below 10 dB respectively, and the 3rd order intercept point is about 17 dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제17권3호
• /
• pp.229-238
• /
• 2006

In this paper, developed study about isolator that after design and optimizes center strip to use 3-D simulator. We use the factor about the change and propose simple mode of the simulation. Design strip line that center frequency is 1.85 GHz by software that use 3-D finite element method(FEM) and confirmed variable. Developed isolator were shown that more than isolation 25 dB, reflection loss has the more than 25 dB and insertion loss does not 0.2 dB. We could confirm that compare with simulation and manufacture sample propertied agrees more than 90 %.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제11권5호
• /
• pp.839-848
• /
• 2000

This paper presents the results of an electromagnetic field analysis for a reverberation chamber that is an alternative method of a shielded anechoic chamber, which is widely used for the analysis and measurement of electromagnetic interference and immunity test. Inside the defined test volume of the rectangular and triangular type, the Schroeder Quadratic Residue Diffuser was employed. FDTD(Finite-Difference Time-Domain) simulation method was applied to produce the field characteristics inside those reverberation chambers. According to the results, field uniformities on the aforementioned two types of reverberation chambers were correlated within $\pm$3dB, and $\pm$4.4dB tolerances, and rectangular type reverberation chamber shows an independent polarization result.