• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.369-374
• /
• 2011

An induction motor operated with high voltage source generally generates high current in starting mode and has a long transient time after being started. This large and sustaining starting current causes the end windings of the stator to have excessive electromagnetic force. This force is the source of vibration and has a negative and serious influence on the insulation of end windings. Therefore, designing the end winding part with an appropriate support system is needed. To design the support ring enclosing the end windings, we analyze the distribution of electromagnetic force on the end windings by applying the Biot-Savart's law and the 3D finite element method (FEM), and comparing two simulation methods. Finally, we verify the safety of the support structure of the end winding part using stress analysis, which is analyzed with the electromagnetic forces from the 3D FEM simulation.

• 한국초전도ㆍ저온공학회논문지
• /
• 제21권3호
• /
• pp.32-37
• /
• 2019

In various types of large-scale electrical applications, the number of coil turns in such machines is usually large. Electromagnetic simulation of large-scale superconducting coils (tens to hundreds of turns) is indispensable in the design process of superconducting electrical equipment. However, due to the large scale of the coil and the large aspect ratio of super-conducting material layer in HTS coated conductor, it is usually difficult or even unable to perform 3-D transient electromagnetic simulation. This paper introduces an effective 3-D electromagnetic simulation method for large-scale HTS coated conductor coil based on T-A formulation. The simulation and experimental results show that the 3-D model based on the T-A formulation using homogeneous strategy is more accurate than the traditional 2-D models. The memory usage is not sensitive to the number of turns and this model will be even more superior as the number of turns becomes larger.

• 소성∙가공
• /
• 제28권3호
• /
• pp.159-166
• /
• 2019

Electromagnetic forming (EMF) simulations consider 3-dimensionally coupled electromagnetic-mechanical phenomenon using LS-DYNA, therefore the calculation cost is normally expensive. In this study, a sensitivity analysis in regard to the simulation variables affecting the calculation time was carried out. The EMF experiments were conducted to form an elliptically protruding shape on a high-strength steel sheet, and it was predicted using LS-DYNA simulation. In this particular EMF simulation case, the effect of several simulation variables, viz., element size, contact condition, EM-time step interval, and re-calculation number of the EM matrices, on the shape of elliptical protrusion and the total calculation time was analyzed. As a result, reasonable values of the simulation variables between the simulation precision and calculation time were proposed, and the EMF experiments with respect to the charging voltages were successfully predicted.

• 인터넷정보학회논문지
• /
• 제23권3호
• /
• pp.67-76
• /
• 2022

현대에는 전자기파를 이용한 전력 및 신호 전달이 필수적인데, 전자기파를 원하는 경로를 통해 효율적으로 전달하기 위해서는 도파 구조(guided structure)가 필요하다. 본 논문에서는 먼저 전파해석 기법인 유한요소법(FEM : Finite Element Method)을 적용하여 도파 구조 중 하나인 2-D/3-D 도파관(waveguide)에 대해 직접 in-house code를 작성하여 전자기 시뮬레이션하였다. 이후 in-house code의 해석 결과를 대표적인 전자파 상용 시뮬레이션 소프트웨어인 HFSS의 결과와 비교하여 해석의 정확성을 검증하였다. 아울러, 전자기 해석에 있어 무한대의 해석 영역을 잘라 해석하기 위해 필수적인 흡수경계조건(ABC : Absorbing Boundary Condition)의 성능을 분석한 후, 병렬화 기법의 적용에 따른 성능 향상을 제시하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1957-1959
• /
• 2004

In this paper, maxwell 3D finite element analysis program was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 2.56[MHz] and some specific conditions.

• Journal of electromagnetic engineering and science
• /
• 제7권4호
• /
• pp.175-182
• /
• 2007

In this paper, a study on the reflector type frequency doubler, to suppress the undesired harmonics, is presented. A 12 to 24 GHz reflective frequency doubler is simulated and experimented. Design procedure of the frequency doubler with reflector is provided and the frequency doubler with good spectral purity is fabricated successfully. It has harmonic suppression of the $40{\sim}50\;dBc$ in the $1^{st}$ harmonic and the $50{\sim}60\;dB$ in the $3^{rd}$ harmonic with no additional filter. And, it has conversion gain with the input power of 0 dBm over bandwidth of 500 MHz. A NEC's ne71300(N) GaAs FET is used and the nonlinear model(EEFET3) using IC-CAP program is extracted for harmonic load pull simulation. Good agreement between simulated and measured results has been achieved.

• Journal of electromagnetic engineering and science
• /
• 제13권4호
• /
• pp.263-266
• /
• 2013

A novel compact and low-loss VHF bandpass filter is presented with enhanced stopband performance using metamaterial zeroth order resonator (ZOR) characteristics. An in-line ZOR filter is initially suggested and changed to have transmission zeros (TZs) due to source-load coupling for effective improvement of the isolation from UHF wireless channels. The proposed filter is smaller than 1/10 of the conventional filters in terms of size and has relatively very low insertion loss (< 1 dB for the electromagnetic (EM) simulation and < 3 dB for the measurement) and return loss (<-20 dB) in the passband due to the approximately 80% size reduction and the higher isolation in the stopband due to the TZs. The circuit and EM simulation are in good agreement with the measurements.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.225-228
• /
• 2000

In this paper, the design for a low noise amplifier with the EM simulation is presented. The ATF36077 pHEMT device is applied to design LNA for U-NII frequency band (5 GHz ～ 6 GHz). The matching networks have been designed by the only open ended stub in order to reduce parasitic effects generated from a via structure. Through EM simulator, the simulation result shows that the linear gain (@5.5 GHz) is over 10 dB, input return loss and output return loss (@ 5.5 GHz) are a below 10 dB respectively, and the 3rd order intercept point is about 17 dBm.

• 한국전자파학회논문지
• /
• 제17권3호
• /
• pp.229-238
• /
• 2006

본 논문에서는 3-D 시뮬레이터를 이용하여 아이솔레이터의 공진기를 설계하고 변화에 대한 factor를 이용하여 단순화된 시뮬레이션 방식을 제안하고 그에 따른 제품의 특성 값을 비교하고자 하였다. 3차원 유한요소법(FEM)을 이용한 소프트웨어로 중심 주파수가 1.85 GHz 대역인 스트립라인을 설계하여 변수를 확인하였으며, 최종 최적화된 스트립라인과 상용화되어 있는 페라이트를 이용하여 삽입 손실, 0.2 dB 이하, 반사 손실과 격리도가 25 dB 이상인 아이솔레이터를 개발하였다. 시뮬레이션 결과와 비교하여 90 % 이상 일치하는 것을 확인할 수 있었다.

• 한국전자파학회논문지
• /
• 제11권5호
• /
• pp.839-848
• /
• 2000

본 논문은 전자파 장해 및 복사내성 측정에 사용되는 전자파 무반사실의 대용 방법으로 활용될 수 있는 전자파 잔향실의 전자기장 특성에 관하여 연구하였다. 체적이 동일한 직사각형 및 삼각형 구조의 잔향실 내부 필드균일성을 확보하기 위하여 Shroeder diffuser 방식을 적용하였으며, FDTD(Finite-Difference Time-Domain) 방법을 사용하여 잔향실 내부의 필드 특성을 조사하였다. 앞에서 언급한 두 가지 형태의 잔향실 내부에서 필드 특성을 조사하기 위해 시험공간 내의 75% 샘플을 가지고 분석하였다. 직사각형 잔향실의 경우 최대 $\pm$3dB, 삼각형 잔향실의 경우 최대 $\pm$4.4dB 내의 tolerance를 나타내었으며, 또한 직사각형 잔향실의 경우 편파에 대해서도 독립적이라는 결과를 얻을 수 있었다.