• Journal of the Korea Knowledge Information Technology Society
• /
• v.12 no.4
• /
• pp.539-550
• /
• 2017

In this paper, we designed, fabricated and tested an UHF band cylindrical dipole array antenna. In the proposed antenna, cylindrical dipoles were vertically arranged in four stages. A parallel structure feeding circuit was installed inside the cylindrical dipole and mounted so as to be broadband matching. The feeding circuit was installed at the center of the cylindrical dipole to optimize the gain flatness characteristic of the azimuth direction omnidirectional radiation pattern. Minimizing the difference between the signals branched from the feeding circuit and realizing the symmetry of the radiation pattern. The required specifications are more than 11.2% bandwidth in UHF band, above 6dBi antenna gain, standing wave ratio of 2:1 or less, less than ${\pm}1dB$ gain flatness in azimuth radiation pattern, more than 13 degrees in elevation radiation pattern of 3dB beamwidth. We confirmed the possibility of implementation through M&S and verified the result of M&S through production and testing. The test results are 11.2% bandwidth in the UHF band, 6.30 to 8.31 dBi gain, 1.53:1 standing wave ratio or less, within ${\pm}0.2dB$ gain flatness in the azimuth radiation pattern, elevation radiation pattern of 3dB beam width was 15.62 to 15.84 degrees. The test result meets all requirements specifications.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.220-223
• /
• 2000

In this study for the development of a 3D pattern mill, we designed its layout which has high stiffness and low-weight structure. We calculated the load of each axis component when 3D pattern mill is under the worst cutting conditions. On base of the calculations, we determined the size of its structure and selected main components of the machine. Also, using FEM we analyzed the layout design of 3D pattern mill to reduce the wcight of structure and increase stiffness of it. According to the load position and direction, shapes and values of the deformation and the stress distributions are calculated, also we calculated the natural frequencies and mode shapes in order ta modify and redesign the weak parts

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.752-757
• /
• 2018

This study presents the performance evaluation results of a 77-GHz waveguide slot array antenna that was fabricated by attaching a patterned printed circuit board(PCB) on a metal block. The 77-GHz waveguide was divided into a top plate and a bottom structure. The top plate was fabricated using a patterned PCB that can implement a fine slot at low cost. The top cover was then bonded to the bottom metal structure with a waveguide trough using anisotropic conductive film. For evaluating the antenna performance, a $1{\times}16$ slot array antenna was fabricated using our proposed method and the gain and pattern were measured and compared with the simulation results. Though the measurement results demonstrate a reduction in gain of around 2.3~3.5 dB compared to the simulation results assuming ideal bonding conditions, the pattern hardly changed and the slot antenna with a gain of approximately 17 dBi at 77 GHz can be easily manufactured at a low cost using the proposed method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37C no.10
• /
• pp.933-939
• /
• 2012

In general, the three-dimensional(3D) coordinates of the manufactured ship blocks are measured using the laser measuring equipment by ship engineers. But, many deflections between the measured coordinates in manufactured step and the designed coordinates in the design step are occurred because of the measuring process of ship blocks manually. Thus, the ship engineer should conform the consistency between the measured coordinates and the designed coordinates step by step, and it largely causes the loss of manpower and time. In this paper, the automated pattern matching algorithm of 3D coordinates for quality control in ship blocks is suggested in order to solve this problem, and the performance of the algorithm is analyzed using the 3D coordinates simulation software developed by our research laboratory. The coordinates matching rate of the measured coordinates in the single/multi ship block(s) is about 90.2% under the tolerated distance error range is 20~25cm.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.5
• /
• pp.107-116
• /
• 2020

The purpose of this study was to compare the pattern of two men's pants for education and two for industry, and to analyze the patterning method that is most suitable for the body shape of middle-aged men. As a result of appearance evaluation for 3D simulation, J pattern was evaluated as the best in most items, and H pattern was analyzed to be the most inappropriate. As a result of measuring the airgap, all four patterns of the waist circumference were evaluated to have very small airgap, and the J pattern had the smallest airgap for the pants. J pattern was analyzed as the most suitable pattern for middle-aged men's body shape by synthesizing the appearance evaluation of virtual wear, color distribution, sectional view, airgap, etc. However, in the case of J pattern, it was analyzed that the pants length needs to be modified. Since this study compared and analyzed only two patterns for education and two for industry, it is thought that the development of pants for middle-aged men should be developed through actual wearing experiments with J patterns.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.12
• /
• pp.1139-1143
• /
• 2007

A simple method for the fabrication of 3D micro-nano hybrid patterns was presented. In conventional fabrication methods of the micro-nano hybrid patterns, micro-patterns were firstly fabricated and then nano-patterns were formatted on the micro-patterns. Moreover, these micro-nano hybrid patterns could be fabricated on the flat substrate. In this paper, we suggested the fabrication method of 3D micro-nano hybrid patterns using micro-indentation on the anodized aluminum substrate. Since diameter of the hemispherical nano-pattern can be controlled by electrolyte and applied voltage in the anodizing process, we can easily fabricated nano-patterns of diameter of loom to 300nm. Nano-patterns were firstly formatted on the aluminum substrate, and then micro-patterns were fabricated by deforming the nano-patterned aluminum substrate. Hemispherical nano-patterns of diameter of 150nm were fabricated by anodizing process, and then micro-pyramid patterns of the side-length of $50{\mu}m$ were formatted on the nano-patterns using micro-indentation. Finally we successfully replicated 3D micro-nano hybrid patterns by hot-embossing process. 3D micro-nano hybrid patterns can be applied to nano-photonic device and nano-biochip application.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.1 s.4
• /
• pp.75-83
• /
• 2004

This paper describes the design, fabrication, and measurement of a low side lobe antenna for RSE base station of the ETCS which is one of the ITS services. The antenna is installed on the gantry of road side and provides the wireless communication lint between vehicles and RSE. The required characteristics of ETCS base station antenna are low sidelobe and specific beam pattern by the road and install environment and installed place of OBU. To minimize the affects of multipath signal by reflection, Circular polarization is required. To get low sidelobe of antenna, array configuration and weighting factor by Taylor distribution in radiator elements are applied. The measured results of fabricated antenna are as follows; return loss of 130MHz by -10dB, an axial ratio of 2.6dB, and a gain of 17dBi. It is found that the measured beam patterns are similar to design results.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.5
• /
• pp.549-556
• /
• 2015

In this paper, design and fabrication for inset fed microstrip patch antennas applied to the $3{\times}3$ array CSLR and eight CSLR, respectively, to the ground plane are studied. The theoretical results are compared to the experimental results for the return loss and radiation pattern. For 'CSLR 09' antenna, the theoretical result for the resonant frequency and the return loss are 2.82 GHz and - 25.35 dB, respectively. The experimental results are obtained for a 2.885 GHz, -30.72 dB. Theoretical results for the resonant frequency and the return loss of the 'CSLR 08' antenna are 2.82 GHz, -16.77 dB, respectively, and the experimental results are obtained for a 2.885 GHz, -14.90 dB. In addition, E-plane and H-plane radiation patterns in comparison with designed and fabricated antennas are in good agreement.

• Fashion & Textile Research Journal
• /
• v.22 no.1
• /
• pp.11-24
• /
• 2020

This research examines pattern production of 3 men's costumes in the second half of 19th century by 3D reconstruction to reveal technical aspects of mail costumes. The steps are as follows. First, an examination of selective type according to research study. Second, a pattern analysis of 3 historical male tops of 19th century referred to 9 pattern books of the France National Library collection. Third, a categorized type analysis that referred to paintings of the Musée d'Orsay collection. Fourth, a measurement and structure research of 3 historical garments of Fashion and Textile Museum collection. Fifth, the pattern making and fitting by 3D simulation. Research discussed the following subjects and results. First, main type of men's coat can be categorized by frac, redingote, jaquette, and veston. Second, the male costume pattern contained in pattern books was researched along with distinguished silhouettes and structures; X silhouette for frac and redingote, H silhouette for jaquette, and straight box silhouette for veston. Third, based on the analysis of representative type of men's costume per period conducted previous studies, 2 redingotes and a jaquette in the museum were selected and compared to other data such as image materials. Last, the following process was conducted for reconstruction; 'Drawing diagram-Primary pattern drafting by measurement value-3D virtual fitting-Checking the fit-Modification and complement'. We also obtained a 3D virtual reconstruction and a 2D research pattern that suggested a costume pattern by each type along with 3D reconstruction that included insights for male coat techniques of 19th century France.

• Fashion & Textile Research Journal
• /
• v.15 no.6
• /
• pp.963-970
• /
• 2013

The purpose of this study was to develop torso pattern of underweight female in their 20s~30s by using Clo 3D virtual garment simulation system. The results were as follows; first, as a result of analyzing torso somatotype, underweight women showed lower average than average values of whole women in their twenties and thirties in the items such as length, width, circumference, thickness except for height. Second, by using 3D virtual garment simulation, new torso pattern considered underweight female was development. The basic numerical formula were as follows ; bust girth B/2+3.5, armhole depth B/4+0.5, front waist girth W/4+0.5+0.7, back waist girth W/4+0.5-0.7, front hip girth H/4+1+0.5, back hip girth H/4+1-0.5, chest width B/6+3.1, back width B/6+4.5, neck width B/12+0.2 and neck depth B/12+1.7. Third, by reducing hollowed amount of front, back, and side line, and hollowed amount of back center line, the reduced quantity was included to darts amount. Number of dart was adjusted to two pieces so that darts amount was equally distributed to two darts. Forth, according to the results of the new torso pattern's appearance evaluation, it estimated more highly than existing pattern in silhouette and ease amount, confirming that new torso pattern was appropriate for the underweight women. This study is expected to serve as one of important basic data for ensuing studies that may utilize 3D virtual garment simulation system with 2D patterns, and also for future 3D pattern production program development.