• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.467-468
• /
• 2006

In this work, we present the comparison between $d_{31}\;and\;d_{33}$ mode characterization using the PZT micro-actuator for large displacement. The PZT micro-actuator consisted of Si, PZT, and Pt layer on SOI wafer. The electrode shapes were laminated and interdigitated for $d_{31}\;and\;d_{33}$ mode, respectively. In order to characterize the actuation mode, we measured the displacement using laser interferometer. The maximum displacement of d31 mode was $12.2{\mu}m$ at 10V, the actuation characterization of d31 was better than that of d33 mode. We estimated that displacement of d33 mode would be larger than that of d31 above 30V.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.2
• /
• pp.184-192
• /
• 2019

Compared to 31-mode rings, 33-mode rings are highly utilized as wide bandwidth underwater acoustic transducers because the electro-mechanical coupling and piezoelectric constant d are high. On the other hand, the 31-mode ring is an axial symmetry structure, so it is possible to model it as a simple two-dimensional asymmetrical model for numerical analysis, but the 33-mode ring requires a three-dimensional numerical analysis. That is, a lot of computing resources and computation time are required. In this study, the effective material properties of an equivalent 31-mode ring were derived to simulate the electro-mechano-acoustical responses of the 33-mode ring transducer. Using the effective material properties derived from this study, a numerical analysis of rings in vacuum, air backed rings in water, and FFR (Free Flooded Ring) transducers were performed to compare the responses of 33-mode rings.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.62-71
• /
• 1996

In this paper, we design tripel-mode channel filter using iris optimization technique and investigate its response. The cavity diameter is determined to resonate three orthogonal modes coincidently and inter-cavity iris is optimized in which one slot control one TE-TE mode and other TM-TM mode couplings simultaneously. Since the electric/magnectic field is variable due to slot position, the center position of the slot which handle coupling coefficients of two modes should be designe dwith optimizatin technique presented here. The implemented triple-mode filter in this paper saves its mass and volume upto 33% relating to the dual-mode filter, caused by the reduced number of cavities.

• Journal of radiological science and technology
• /
• v.40 no.2
• /
• pp.297-302
• /
• 2017

In this study, the generation of photoneutrons between the 10 MV FF mode and the FFF mode was evaluated and the amount of photoneutrons generated by the 10 MV and 15 MV energy changes in the FFF mode was evaluated. The generated neutrons were evaluated at 13 measurement points and the KTEPC was used to collect the generated neutrons. 10 MV FF mode was measured at 10 MV FF mode and FFF mode at all measurement points. In the superior direction, 0.455mSv and 0.152mSv were the largest, and more than 33% optical neutron was generated in FF. 10 MV in FFF mode, 15 MV in 15 MV, and 0.402 mSv in the direction of Superior, and 6.9% in the direction.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.3
• /
• pp.270-275
• /
• 2013

In this study, focusing of ultrasonic Lamb wave by negative refraction with mode conversion from antisymmetric to symmetric mode was investigated. When a wave propagates backward by negative refraction, the energy flux is antiparallel to the phase velocity. Backward propagation of Lamb wave is quite well known, but the behavior of backward Lamb wave at an interface has rarely been investigated. A pin-type transducer is used to detect Lamb wave propagating on a steel plate with a step change in thickness. Conversion from forward to backward propagating mode leads to negative refraction and thus wave focusing. By comparing the amplitudes of received Lamb waves at a specific frequency measured at different distance between transmitter and interface, the focusing of Lamb wave due to negative refraction was confirmed.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.12
• /
• pp.985-992
• /
• 2016

Bearings have various uses in industrial equipment. The lifetime of bearings is often lesser than anticipated at the time of purchase, due to environmental wear, processing, and machining errors. Bearing conditions are important, since defects and damage can lead to significant issues in production processes. In this study, we developed a method to diagnose faults in the bearing conditions. The faults were determined using kurtosis, average, and standard deviation. An intrinsic mode function for the data from the selected axis was extracted using empirical mode decomposition. The intrinsic mode function was obtained based on the frequency, and the learning data of ANN (Artificial Neural Network) was concluded, following which the normal and fault conditions of the bearing were classified.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.22-27
• /
• 2004

In this paper, we designed a mode size converter to reduce coupling loss between optical waveguide and single mode fiber. The proposed mode converter is composed of periodically segmented tapered waveguide to achieve small size and easy fabrication. For the optimally designed mode size converter at 1550nm, the taper length is 500(equation omitted), the segmentation period 5ß:, the waveguide width of fiber contact section 1.3ß:, and duty cycle 0.95. The coupling loss of the optimized mode size converter is 0.33㏈/point, which is 1.27㏈/point lower than that without the mode size converter.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.4
• /
• pp.83-90
• /
• 2004

In this paper, we proposed a new instruction set(X32Y ISA) with 3 different types of instruction mode. The proposed instruction set organizes 32-bit, 24-bit, 16-bit instruction in order to solves a problem of memory size limitation in an embedded microprocessor. We designed a 32-bit 5 stage pipeline RISC microprocessor based on the X32V ISA. To verify the proposed the X32V ISA and a microprocessor, we estimated a program code size of multimedia application programs using a X32V simulator. In result, we verified that the Light mode and the Ultra Light mode obtains 8%, 27% reduction of a program code size through comparison with the Default mode. The proposed microprocessor was verified all X32V instructions execution at Xilinx FPGA with 33MHz operating frequency,

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.11
• /
• pp.1719-1732
• /
• 2009

A firm seeking to enter a foreign market must make an important strategic decision of which market entry mode to use. Because entry modes involve resource commitments, the initial choice by a firm on a particular entry mode is difficult to change without a considerable loss of time and money. Substantial prior research has been undertaken to explain why firms select a particular entry mode into global markets. However, there exists limited research on this area in the field of foreign apparel brands in Korea, although some research has analyzed influential entry mode factors when Korean textile and clothing companies went overseas. This study reviews prior research on the entry mode choice and analyzes the factors that influence the entry mode choice for 510 foreign clothing brands in Korea. Price range, clothing types, distribution strategy, and cultural distance were considered as influential determinants for different entry mode choices. Crosstabs with a chi-square test and logistic regression are used for analysis. This study shows that high-priced brands and luxury brands are associated with the export orientated entry mode in the Korean market. Brands that pursued the strategy of multiple distribution channels showed a preference for a licensing mode or direct investment over other entry modes, and brands from higher-cultural-distance countries entered the Korean clothing market by licensing mode. The findings of this study are appropriate for the strategic planning of foreign apparel intent on entering the Korean market or for Korean apparel firms planning to enter the global market.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.1
• /
• pp.27-33
• /
• 2009

Human postural responses appeared to have stereotyped modality, such as ankle mode, knee mode and hip mode in response to various perturbations. We examined whether human postural control gain of full-state feedback could be decoupled along with the eigenvector. To verify the model, postural responses subjected to fast backward perturbation were used. Upright posture was modeled as 3-segment inverted pendulum incorporated with feedback control, and joint torques were calculated using inverse dynamics. Postural modalities such as ankle, knee and hip mode were obtained from eigenvectors of biomechanical model. As oppose to the full-state feedback control, independent eigenvector control assumes that modal control input is determined by the linear combination of corresponding modality. We used optimization method to obtain and compare the feedback gains for both independent eigenvector control and full-state feedback control. As a result, we found that simulation result of eigenvector feedback was not competitive in comparison with that of full-state feedback control. This implies that the CNS would make use of full-state body information to generate compensative joint torques.