• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.153-154
• /
• 2007

AISI316L강은 AISI304L강과 기본 조성은 같지만 316L강이 약 2.5%의 Mo가 첨가되어 있다. 저온 플라즈마 질탄화 시 모재에 첨가된 Mo의 영향을 조사하기 위하여 처리온도를 변화시켜 실험하였다. 같은 처리온도의 경우 경화층의 두께는 316L강이 비교적 두껍게 형성되었다. 316L강의 경우 $450^{\circ}C$이하에서 약 25 ${\mu}m$까지 형성되었고, 306L강의 경우 $400^{\circ}C$에서 약 10 ${\mu}m$까지 형성되었다. $400^{\circ}C$ 이하에서 경화층은 두 가지시편 모두 확장된 오스테나이트 (${\gamma}_N,\;{\gamma}_c$)로 이루어져 있으나, 304L의 경우 $430^{\circ}C$부터 석출물(CrN)이 형성되기 시작하였다. 316L의 경우 $450^{\circ}C$까지 석출물이 형성되지 않았고, $480^{\circ}C$에서 석출물 (CrN)이 관찰되었다. 석출물이 형성된 시편을 제외한 모든 시편의 내식성은 모제보다 증가 하였다.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.147-154
• /
• 2008

The general corrosion behavior of austenitic and ferritic steels(316L, 304, N controlled 304L, and 410) in supercritical water is investigated in this paper. After exposure to deaerated supercritical water at $480^{\circ}C$/25 MPa for up to 500 h, the four steels studied were characterized using gravimetry, scanning electron microscopy/energy dispersive X-ray spectroscopy(SEM/EDS), X-ray photoelectron spectroscopy(XPS), and X-ray diffraction(XRD). The results show that the 316L steel with a higher Cr and Ni content has the best corrosion-resistance performance among the steels tested. In addition to the oxide layer mixed with $Fe_{3}O_{4}$ and $(Fe,Cr)_{3}O_{4}$ that formed on all the samples, a $Fe_{3}O_{4}$ loose outer layer was observed on the 410 steel. The corrosion mechanism of stainless steels in supercritical water is discussed based on the above results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.68-74
• /
• 2011

This papers investigated the mechanical characteristics and the weldability of identical as well as dissimilar welding by GTAW for STS 304 and STS 316L. It is applied to double wall gas pipe of duel fuel engine for LNG carrier. Consequently, the weldability of dissimilar and identical welded zone of STS 304 decreased compared to base metal significantly. The result of microstructure observation for welded zone, a degree of acicular ferrite in welding zone for STS 304 presented more than STS 316L. The hardness of welding zone for STS 304 presented higher value than that for STS 316L by this effect.

• Nuclear Engineering and Technology
• /
• v.27 no.4
• /
• pp.453-462
• /
• 1995

In connection with the safe storage of high level nuclear waste, effect of $H_2O$$_2$ on the corrosion behavior of 304L stainless steel was examined. Open circuit potentials and polarization curves were measured with and without $H_2O$$_2$. The experimental results show that $H_2O$$_2$ increased corrosion potential and decreased pitting potential. The passive range, therefore, decreased as $H_2O$$_2$ concentration increased, indicating that pitting resistance was decreased by the existence of $H_2O$$_2$ in the electrolyte. These effect of $H_2O$$_2$ on corrosion of 304L stainless steel are considered to be similar to those of ${\gamma}$-irradiation. To compare the effects of $H_2O$$_2$ with those of $O_2$, cathodic and anodic polarization curves ore made in three types of electrolyte such as aerated, deaerated, and stirred electrolyte. The experimental results show that the effects of $H_2O$$_2$ on the corrosion behavior were tory similar to those of $O_2$ such as increase of corrosion potential, decrease of pitting resistance, and increase of repassivation potential. In acid and alkaline media, the corrosion potential shifts by $H_2O$$_2$ were restricted by the large current density of proton reduction and by the le Chatelier's principle respectively.y.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.11
• /
• pp.131-137
• /
• 2009

A pair of connectors for transferring torque is widely used in various types of a mechanical system. By the repetition of mechanical contact between a pair of connector, wear occurs easily. This kind of defect sometimes can cause a serious problem of health in case of the connector is used in a refrigerator. In this work, the material combination of connectors was experimentally studied to reduce the amount of wear; for the combination of connectors, various types of engineering materials including polyacetal, polycabonate, stainless steel (STS-304), NiP coated STS-304, and STS-310 were evaluated to check each wear behavior. Also an effective method of wear test was suggested for precise controlling of wear conditions such as contact area, contact force, and relative motion speed. From the test results, it was found out that a pair of polyacetal to STS-304 and STS-310 showed the lowest specific wear rates among other pairs.

• Steel and Composite Structures
• /
• v.28 no.3
• /
• pp.349-362
• /
• 2018

This paper presents a semi-analytical solution for the creep analysis and life assessment of 304L austenitic stainless steel thick truncated conical shells using multilayered method based on the first order shear deformation theory (FSDT). The cone is subjected to the non-uniform internal pressure and temperature gradient. Damages are obtained in thick truncated conical shell using Robinson's linear life fraction damage rule, and time to rupture and remaining life assessment is determined by Larson-Miller Parameter (LMP). The creep response of the material is described by Norton's law. In the multilayer method, the truncated cone is divided into n homogeneous disks, and n sets of differential equations with constant coefficients. This set of equations is solved analytically by applying boundary and continuity conditions between the layers. The results obtained analytically have been compared with the numerical results of the finite element method. The results show that the multilayered method based on FSDT has an acceptable amount of accuracy when one wants to obtain radial displacement, radial, circumferential and shear stresses. It is shown that non-uniform pressure has significant influences on the creep damages and remaining life of the truncated cone.

• Korean Journal of Metals and Materials
• /
• v.48 no.12
• /
• pp.1090-1096
• /
• 2010

This pitting corrosion study of welded joints of austenitic stainless steels (AISI 304L and 316L) has addressed the differentiating solidification mode using three newly introduced filler wires with a flux-cored arc welding process (FCAW). The delta ferrite (${\delta}$-ferrite) content in the welded metals increased with an increasing equivalent weight ratio of chromium/nickel ($Cr_{eq}/Ni_{eq}$). Ductility dip cracking (DDC) was observed in the welded metal containing ferrite with none of AISI 304L and 0.1% of AISI 316L. The potentiodynamic anodic polarization results revealed that the $Cr_{eq}/Ni_{eq}$ ratio in a 3.5% NaCl solution didn't much affect the pitting potential ($E_{pit}$). The AISI 316L welded metals with ${\ddot{a}}$-ferrite content of over 10% had a superior $E_{pit}$ value. Though the AISI 316L welded metal with 0.1% ferrite had larger molybdenum contents than AISI 304L specimens, it showed a similar $E_{pit}$ value because the concentration of chloride ions and the corrosion product induced severe damage near the DDC.

• Corrosion Science and Technology
• /
• v.17 no.6
• /
• pp.279-286
• /
• 2018

Austenitic stainless steels used in nuclear power plants mainly use pipes made of seamless pipes, which depend on imports. The manufacturing process and high cost are some of the problems associated with seamless pipes. Therefore, in this study, the corrosion characteristics of the seamless pipe and the SAW pipe were assessed to determine the safety and reliability of the SAW pipe in a bid to replace the seamless pipe. Microstructure was analyzed using an optical microscope and the degree of hardness was measured using a Rockwell B scale. Intergranular corrosion resistance was evaluated by ASTM A262 Practice A, C, and E methods. The degree of sensitization was determined using a DL-EPR test. Anodic polarization test was performed in deaerated 1% NaCl solution at $30^{\circ}C$ and the U-bend method was used to evaluate the SCC resistance in 0.01 M $Na_2S_4O_6$ at $340^{\circ}C$ and 40% NaOH solution at $290^{\circ}C$. Weld metal of the SAW pipe specimen showed relatively high degree of sensitization and intergranular corrosion rate. However, annealing to SAW pipes improved the corrosion properties in comparison to that of the seamless pipe.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.59-68
• /
• 1998

In this study, effects of solidification modes (primary $\delta$-ferrite, primary ${\gamma}$-austenite) on the pit initiation and propagation in the 304L and 316L austenitic stainless steel weld metals were investigated. The solidification mode of weld metal was controlled by the addition of nitrogen to Ar shielding gas. Through the electrochemical experiments (potentiodynamic anodic polarization and potentiostatic time-current transient test) and metallographic examination (microstructure and elemental distribution), the following results were obtained. The more the volume content of nitrogen in the shielding gas were, the lower critical current density for passivity was observed. In comparison with weldments solidified through the primary $\delta$-ferrite solidification mode and the primary ${\gamma}$-solidification mode, the former showed higher critical pitting potential and a longer incubation time for stable pit initiation than the latter. However, in the pit propagation stage the former exhibited a faster dissolution rate than the latter. These results were believed to ee related to the distribution of alloying elements such as Cr, Mo, Ni and S.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.317-327
• /
• 2024

This study investigated the chloride-induced stress corrosion cracking (CISCC) behavior expected to occur in welds of austenitic stainless steel, which are considered candidate materials for dry storage containers for spent nuclear fuel. The behavior was studied by varying temperature, relative humidity (RH), and chloride concentration. 304L-ER308L welded plates were processed into U-bend specimens and exposed to a cyclic corrosion chamber for 12 weeks. The CISCC behavior was then analyzed using electron microscopy. A previous study by the authors confirmed that CISCC occurred in ER308L at 60 ℃, 30% RH, and 0.6 M NaCl via selective corrosion of δ-ferrite. When the temperature was lowered from 60 ℃ to 50 ℃, CISCC still occurred. However, when the humidity was reduced to 20% RH, CISCC did not happen. This can be attributed to the retardation of the deliquescence of NaCl at lower humidity, which was insufficient to promote CISCC. Furthermore, increased chloride concentration to 1.0 M resulted in the absence of CISCC and widespread surface corrosion with severe pitting corrosion because of the increase in thin film thickness.