• 한국수소및신에너지학회논문집
• /
• 제20권4호
• /
• pp.291-299
• /
• 2009

Ni-plated polytetrafluoroethylene(Ni-PTFE) particles($25{\mu}m$, $500{\mu}m$) were prepared by using nickel electroless plating. The Ni content in Ni-PTFE particles increased with increasing the amount of reduction agent. At about 53 wt% Ni content, $25{\mu}m$ Ni-PTFE particles showed conductivity of 320S/m. The Ni-PTFE particles were formed into the Ni-PTFE plate using heat treatment at $350^{\circ}C$ under $10{\sim}1000kg/cm^2$. The Ni-PTFE plate displayed the high conductivity of 5100S/m due to the formation of 3-dimentional Ni network. The plate was used as an electrode in an alkaline fuel cell(AFC). In terms of the current density, the Ni-PTFE electrode having higher Ni content(53 wt%) showed improved performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.32-35
• /
• 1996

This paper analyzes characteristics of PMLSM using 3 dimensional equivalent magnetic circuit network method (3-D EMC). PMLSM of which the effective electric-airgap is not only very large, but also the width is finite width lateral edges has much leakage flux. Therefore, 2-D analysis method cannot consider it so carefully that 3-D analysis method must required. 3-D EMC which will be used for analysis of PMLSM performs modeling of it including solt and teeth structure, uses the magnetic motive force of stator winding and permanent magnet as source. and calculates magnetic flux density and force considering nonlinear characteristics of materials. we verified analysis validity by comparing simulation results with expermental results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권5호
• /
• pp.228-233
• /
• 2002

A computational method for analysis of the 3 dimensional electro-magnetic induction problems has been developed. The developed method is capable of modeling the induced current and analyzing its characteristics using only scalar Potential at each node. A benchmark model of asymmetrical conductor with a hole is analyzed to verify the application of the developed method. The calculated value of magnetic flux density are compared with the measured value, and the results indicate that the developed method is valid. Also, Comparing with 3-D finite element method (FEM) results, we conformed effectiveness of the developed method for the accuracy and computation times.

• 한국측량학회지
• /
• 제11권2호
• /
• pp.27-34
• /
• 1993

정확하고 경제성 있는 지형정보의 구축은 각종 건설공사를 비롯한 국토종합개발에 기본 요건으로서 그 중요성이 강조되고 있다. 본 연구에서는 남한 지역을 대상으로 하는 광역망과 충남·북 일원의 지역망내, 1, 2 등 삼각점에 대한 GPS 관측을 수행하여 WGS 84 좌표를 조정·산출하고 Bessel 타원체 상의 좌표로 변환하기 위한 변환계수론 Bessel Geoid Undulation을 고려한 7-Parameter 변환기법으로 도출하므로서, GPS에 의한 정밀 3차원 지형정보의 획득은 물론, 순변환된 성과와 역변환된 성과에 각각 T.M. 및 U.T.M 투영도법을 적용하여 정밀 지도제작을 위한 기본 자료의 산출 가능성을 제시코자 한다.

• 전기학회논문지
• /
• 제62권10호
• /
• pp.1475-1480
• /
• 2013

In this paper, the basic design study of a water-cooling jacket, which have reported no cases for applying to railway traction motors so far, were conducted for applying to Interior Permanent Magnet Synchronous Motor (IPMSM) for railway vehicles. The basic thermal characteristics analysis of the 110kW-class IPMSM was performed by using 3-dimentional thermal equivalent network method. The necessary design requirements of the water-cooling jacket were derived by analyzing the results of the basic thermal properties. Next, the thermal characteristics analysis technique was established by using the equivalent model of the solenoid-typed pipe to be installed on the inside of the water-cooling jacket for 110kW-class IPMSM. Finally, a design model of 6kW-class water-cooling jacket was derived through the analysis of various design parameters.

• 한국인쇄학회지
• /
• 제18권1호
• /
• pp.59-69
• /
• 2000

The characteristics of liquid crystal polymer composite(LCPC) films are possessed of large-area and flexible display, polarizer free, high contrast, wide angle of visual filed and high responsiveness. It is well known that the LCPC films consisting of a continuous LC phase embeded in a three-dimentional network of polymer matrix are formed by photopolymerization-induced phase separation. In this study, we have investigated the point that both liquid crystals and polymer having different properties have to coexiste as composed films. The purpose of this study has been the development of new application with liquid crystals and UV-curable monomers. In the results abtained on the miscibility of nematic liquid crystal and UV-curable resins, difunctional monomer HX-620 turned out to shows the best. From the results abtained on structures, electro-optical properties and dynamic visocoelasticity for LCPC films, the best mixing ratio of monomer to LC mixture were 3/7(photoinitiator; 4wt%) by weight, and this ratio has been provided the most thermal stability for LCPC films. In the results abtained on structure and discoloration properties of LCPC films, it has been demonstrated that consiste of a 8:2 mixture of chiral nematic liquid crystal and HX-620 has the greatest domain and it was the best discoloration.

• 한국환경과학회지
• /
• 제4권5호
• /
• pp.75-75
• /
• 1995

In order to provide for the guidance on groundwater quality monitoring network design and also, to suggest the index to the solution of the contaminated groundwater remediation problems in the lake watershed, it is necessary to analyze the contaminant transport in the groundwater. The solute transport was analyzed in the lake watershed to investigate the behavior of the injected contaminant sources depend on the relationships between the point of contaminant sources and position of the lake. Three hypothetical groundwater flow systems, which is composed of a flow-through lake and two solute sources, were considered. The lakes located in the upper, middle, and lower portions of a watershed respectively. The transported contaminant was numerically simulated for five years by using MT3D contaminant transport model under the three-dimentional steady state conditions. From the above simulations, it can be concluded that the contaminant concentration was high as the contaminant source located at the upper position of a watershed, and the influence of the contaminant injection was large as the solute source located at the lower position. When the injection of contaminant was continued for one year without regard to the position of contaminant source and the lake, the influence of contaminant source was reached to bedrock.

• 한국환경과학회지
• /
• 제4권5호
• /
• pp.461-468
• /
• 1995

In order to provide for the guidance on groundwater quality monitoring network design and also, to suggest the index to the solution of the contaminated groundwater remediation problems in the lake watershed, it is necessary to analyze the contaminant transport in the groundwater. The solute transport was analyzed in the lake watershed to investigate the behavior of the injected contaminant sources depend on the relationships between the point of contaminant sources and position of the lake. Three hypothetical groundwater flow systems, which is composed of a flow-through lake and two solute sources, were considered. The lakes located in the upper, middle, and lower portions of a watershed respectively. The transported contaminant was numerically simulated for five years by using MT3D contaminant transport model under the three-dimentional steady state conditions. From the above simulations, it can be concluded that the contaminant concentration was high as the contaminant source located at the upper position of a watershed, and the influence of the contaminant injection was large as the solute source located at the lower position. When the injection of contaminant was continued for one year without regard to the position of contaminant source and the lake, the influence of contaminant source was reached to bedrock.

• Restorative Dentistry and Endodontics
• /
• 제24권1호
• /
• pp.100-115
• /
• 1999

The purpose of this study was to investigate the distribution of calcitonin gene-related peptide containing nerve fibers in rat pulp after dentinl injury by means of immunohistochemistry and confocal laser scanning microscope. The Spague-Dawley rats weighing about 250-300gm were used. The animals were devided into normal control and experimental groups. Experimental animals were sacrified 1, 2, 4, 7, 10, 21days after dentinal injury (dentin cutting, and then acid etching with 35% phosphoric acid) on the maxillary molar teeth. The maxillary teeth and alveolar bone were removed and immersed in the 4% paraformaldehyde in 0.1M phosphate buffer (pH 7.4), then were decalcified with 15% formic acid for 10 days. Serial frozen $50{\mu}m$ thick sections were cut on a cryostat. The rabbit CGRP antibody was used as a primary antibody with a dilution of 1:2000 in 0.01M PB. The sections were incubated for 48 hours at $4^{\circ}C$, and placed into biotinylated antirabbit Ig G as a secondary anti body with dilution of 1:200 in 0.01M PB and incubated in ABC(avidin-biotin complex). The peroxidase reaction was visualized by incubating the sections in 0.05% 3,3 diaminobenzidine tetrahydrochloride containing 0.02% $H_2O_2$. For the confocal laser scanning microscopic examination, Primary antibody reaction was same as immunoperoxidase stainning, but fluorescein isothiocyanate(FITC)-conjugate antirabbit IgG as a secondary antibody was used. The confocal laser scanning microscope was used for the examination. A series of images of optical sections was collected with a 20x objective at $3{\mu}m$ intervals throughout the depth of specimen. FITC fluerescence was registrated through a 488nm and 568nm excitation filter, and images were saved on optical disk. The stereoscopic images and three dimentionnal images were reconstructed by computer software, and then were analyzed. The results were as follows : 1. In normal control group, CGRP containing nerve fibers were coursed through the root with very little branching, and then formed a dense network of terminals in coronal pulp. 2. A slight increase in CGRP containing nerve fibers at 1 and 2day postinjury was noted subjacent to the injury site. In the 4day group, there were an extensive increase in the number of reactive fibers, followed by a partial return toward normal levels at 7~10 day postinjury, and return by 21days. 3. The sprouting of the CGRP containing nerve fibers was evident within 2day after dentinal injury, and by 4days there was a maximal increased, but was decreased at 7days and returned to normal 10~21 day postinjury. 4. In confocal laser scanning microscopic exammination, the distinct distribution pattern and sprouting reaction of CGRP containing nerve fibers were observed in stereoscopic images and three dimentional images. These results suggest that CGRP containing nerve fiber can be important role in the response to dental injury and pain regulation.