• Journal of the Korean Magnetics Society
• /
• v.25 no.3
• /
• pp.83-86
• /
• 2015

Nowadays the weapon systems are employed air bursting munition (ABM) as smart programmable 40 mm shells which have been developed in order to hit the target with programmed munition that can be air burst after a set distance in the battlefield. In order to improve the accuracy of such a bursting time, by measuring the speed of the munition from the barrel, weapon systems calculate the exact time of flight to the target and then the time information must be inputted to the munition. In this study, we introduce a device capable of detecting a shot at K4 40 mm automatic grenade. The shot is composed of a rotating copper band to convert linear motion into rotary motion when it passes through the barrel, the steel section is exert the effect of fragment and aluminum section to give fuze information. The aluminum section was used to detect munition using eddy current method. To measure muzzle velocity by means of non-contact method, two eddy current probes separated 10 cm was employed. Time interval between two eddy current probe detection times was used as muzzle velocity. The eddy current probe was fabricated U-shape Mn-Zn ferrite core with enamelled copper wire, and 200 kHz alternating current was used to detect inductance change. Measured muzzle velocity using the developed sensor was compared to the Doppler radar system. The difference was smaller than 1%.

• Annals of Clinical Neurophysiology
• /
• v.13 no.2
• /
• pp.80-86
• /
• 2011

Background: A dry-type electrode is an alternative to the conventional wet-type electrode, because it can be applied without any skin preparation, such as a conductive electrolyte. However, because a dry-type electrode without electrolyte has high electrode-to-skin impedance, an impedance-converting amplifier is typically used to minimize the distortion of the bioelectric signal. In this study, we developed an active dry electroencephalography (EEG) electrode using an impedance converter, and compared its performance with a conventional Ag/AgCl EEG electrode. Methods: We developed an active dry electrode with an impedance converter using a chopper-stabilized operational amplifier. Two electrodes, a conventional Ag/AgCl electrode and our active electrode, were used to acquire EEG signals simultaneously, and the performance was tested in terms of (1) the electrode impedance, (2) raw data quality, and (3) the robustness of any artifacts. Results: The contact impedance of the developed electrode was lower than that of the Ag/AgCl electrode ($0.3{\pm}0.1$ vs. $2.7{\pm}0.7\;k{\Omega}$, respectively). The EEG signal and power spectrum were similar for both electrodes. Additionally, our electrode had a lower 60-Hz component than the Ag/AgCl electrode (16.64 vs. 24.33 dB, respectively). The change in potential of the developed electrode with a physical stimulus was lower than for the Ag/AgCl electrode ($58.7{\pm}30.6$ vs. $81.0{\pm}19.1\;{\mu}V$, respectively), and the difference was close to statistical significance (P=0.07). Conclusions: Our electrode can be used to replace Ag/AgCl electrodes, when EEG recording is emergently required, such as in emergency rooms or in intensive care units.

• Journal of the Korean Vacuum Society
• /
• v.18 no.1
• /
• pp.9-14
• /
• 2009

We calculated tetragonal-$HfO_2$/Si superstructures using density functional theory. When a and b-axes of cubic-$HfO_2$ were increased to be matched with those of Si for epitaxy contact, c-axis was decreased by 2%. Eight models of interface layers were produced by choosing different terminating layers of tetragonal-$HfO_2$ and Si substrate at the interface. It was found that tetragonal-$HfO_2$ $(004)_{1/4}$/Si $(004)_{3/4}$ superstructure was the most favorable and tetragonal-$HfO_2$ (004)$_{1/4}$/Si (002) superstructure was the most unfavorable. In tetragonal-$HfO_2$ $(004)_{1/4}$/Si (002) superstructure, there were two oxygen vacancies in tetragonal-$HfO_2$ as two oxygen atoms were moved to Si substrate located at the interface.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.1
• /
• pp.1-12
• /
• 2021

In the design of a tunnel boring machine (TBM), the excavation efficiency of the equipment depends on the design of the cutter head, which is directly in contact with the ground. Especially, the allocation of disc cutter is crucial issue. Disc cutters can be divided into center cutter zone, inner cutter zone and transition cutter zone depending on where they are placed. Many studies have been conducted to identify optimal cutting conditions for face cutters. However, research to determine the optimal cutting conditions for the transition cutter has been relatively incomplete. In this study, to identify the optimal cutting conditions for the transition cutter, numerical analysis using discrete element method was performed, and the specific energy curve according to the angle between the transition cutters was drawn to find out the optimum cutting conditions. The results show that the angle between the transition cutters showing minimum specific energy in the transition cutter zone is 9°. Transition cutter zone was divided into three sections according to the slope angle of the transition cutter. It is also found that, the greater the slope angle of the transition cutter. This finding shows good agreement with the present design of transition cutter zone.

• Composites Research
• /
• v.33 no.6
• /
• pp.365-370
• /
• 2020

The icing formation at aircraft occur problems such as increasing weight of the body, fuel efficiency reduction, drag reduction, the error of sensor, and etc. The viscosity of polyurethane (PU) topcoat was measured at 60℃ in real time to set the pre-curing time. SiO2 nanoparticles were dispersed in ethanol using ultra-sonication method. The SiO2/ethanol solution was sprayed on PU topcoat that was not cured fully with different pre-curing conditions. Surface roughness of SiO2/PU nanocomposites were measured using surface roughness tester and the surface roughness data was visualized using 3D mapping. The adhesion property between SiO2 and PU topcoat was evaluated using adhesion pull-off test. The static contact angle was measured using distilled water to evaluate the hydrophobicity. Finally, the pre-curing time of PU topcoat was optimized to exhibit the hydrophobicity of SiO2/PU topcoat.

• Journal of the Korean Burn Society
• /
• v.22 no.2
• /
• pp.66-70
• /
• 2019

Purpose: The necrotizing fasciitis is a terrifying infectious disease that can rapidly spreads to surrounding tissues when fascia is infected and it can cause sepsis to death if not properly diagnosed and treated. The purpose of this study is to investigate the characteristics, causes, and treatment methods of necrotizing fasciitis in Korea through reviewing patients admitted to our burn center. Methods: 21 patients with necrotizing fasciitis were selected for this study among those inpatients with electronic medical records (EMR) admitted to Hallym University Hangang Sacred Heart Medical Center from Jan 1, 2008 to June 30, 2019. The medical records and wound photos of those 21 selected subjects were reviewed. Results: There were 13 male and 8 female patients and mean age was 58.76 years old. 13 of 21 subjects were survived and 8 died (38% mortality rate). The surgical treatments performed were I&D, fasciotomy, debridement, allograft, burring, STSG, flap, and amputation. The most common causes were burns in 9 subjects (6 contact burns) and cellulitis occurred on skins in 5 subjects. And other various causes were observed as fournier's gangrene, stab wound, intramuscular injection, tumor and bleu toe syndrome (toe necrosis). The infected areas were 11 feet and legs, 7 hips, 3 abdomen and trunk in 21 subjects. Of the 8 deaths, 3 were infected in feet and legs, 2 were infected in hips, and 2 were infected in abdomen and trunk. As for underlying diseases, 12 patients with hypertension or diabetes were the highest and others such as cancer and stroke were found. Conclusion: The only method to increase the survival rate is to 'suspect' the disease as much as possible and perform early extensive excision. It is advisable to treat the disease by the burn center to properly provide adequate and optimal wound management, infection control, medical care and nutritional supports.

• Analytical Science and Technology
• /
• v.19 no.3
• /
• pp.255-262
• /
• 2006

In this study, we attempted to evaluate the sorptive loss of VOC upon their contact with different material surfaces including clothing pieces. For the purpose of this study, we developed a method to evaluate such loss by employing a filter holder pack in the thermal desorption line of the GC/FID system. The calibration curves of different aromatic VOCs including benzene, toluene, and xylene were made by loading them at different quantities through the analytical line. A series of experiments were conducted repetitively to draw calibration data sets for all three materials covering glass fiber, cotton, and nylon. The results were then compared in terms of both material types and of VOC types. The extent of sorptive loss increased in a highly systematic manner across different materials such as glass fiber, cotton, and nylon. The patterns of sorptive loss also increased gradually across VOC type such toward in the direction of increasing molecular weights: benzene, toluene, and xylene. According to this experimental study, it is concluded that sorptive behavior of pollutint compounds like VOC can be controlled by the combined effects of both chemical properties and material characteristics.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.2
• /
• pp.63-68
• /
• 2024

With the increasing use of transparent displays and flexible devices, polymer substrates offering excellent flexibility and strength are in demand. Since polymers are sensitive to heat, precise temperature control during the process is necessary. The study proposes a temperature measurement system for the laser processing area within the polymer base, aiming to address the drawbacks of using these polymer bases in laser-based selective processing technology. It presents the possibility of optimizing the process conditions of the polymer substrate through local temperature change measurements in the laser processing area. We developed and implemented the PDPT (Photodiode-based Planck Thermometry) to measure temperature in the laser-processing area. PDPT is a non-destructive, contact-free system capable of real-time measurement of local temperature increases. We monitored the temperature fluctuations during the laser processing of the polymer substrate. The study shows that the proposed laser-based temperature measurement technology can measure real-time temperature during laser processing, facilitating optimal production conditions. Furthermore, we anticipate the application of this technology in various laser-based processes, including essential micro-laser processing and 3D printing.

• Journal of Animal Science and Technology
• /
• v.45 no.4
• /
• pp.649-658
• /
• 2003

Early introducing the ducks into the paddy field involves a variety of environmental changes such as new surroundings and contact with water, so that some free-ranged ducks show behavioral and physiological changes indicative of stress or die from not adapted for new circumstances. Moreover, the free-ranged ducks was tread on the rice plant, and required a great deal of labor and time for captured the ducks after finishing the introducing. The aim of the present study was to examine the effect of accustoming and imprinting of duckling on behavior patterns, body weight gain and yield of the rice plant in paddy fields. Three paddy plots were used as control (no imprinting and no contact with people), taming (imprinting and regular handling) and roughness (handling roughly and strike terror to ducks) plots. Right after introducing the ducks into the paddy field, eating and moving behaviour of taming plot ducks tended to be longer time spend than that of other treatments. However, eating and moving time tended to be longer in the control than that of other two treatments on the 2 weeks after. Flighting distance was not showed in the free-ranging period taming plot, but the control plot was significantly (P<0.05) longer than the roughness plot. The captured time of free-ranged ducks tended to be shorter in the order of taming, control and roughness plots. Body weight gains was not significant. The number of rice plants damaged by free-ranging ducks in the taming plot were significantly (P<0.05) less than that in the control plot, but the yield and yield components of the rice plant were not differ among 3 treatments. These results indicated that the imprinting or regular handling and related treatments of duckling was reducing badly damage of rice plants, captured time and labor of free-ranged ducks in paddy field, although the working behavior of ducks and yield ability of the rice plants were not affected.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.