• Journal of the Korean Wood Science and Technology
• /
• v.18 no.4
• /
• pp.26-40
• /
• 1990

The plane trees(Platanus occidentalis L.) have been grown in Korea very widely as ornamental garden or street trees but they have not been used as manufacturing materials The proportion of imported wood has been now over 85% of raw materials needed in the wood industry, and therefore, many of studies on the substitution of domestic wood for imported wood and on the increasing the utilization rate of domestic species have been attempted and considered as very important projects to solve. From a this point of view, this study was carried out to investigate solid wood bending properties of plane trees and then to develop their end-uses, and the size of specimens tested was $15\times15\times350mm$ for steaming treatment and they were dried to $15\pm1%$ before bending. The results obtained were as follows: 1. The optimum conditions for solid wood bending processing of Platanus occidentalis are showed in Table 7. 2. The minimum solid-bending radii of Platanus occidentalis were 40mm in steaming treatment. 3. The effect of knots, diagonal grain and decay on the degradation of bending processing properties were very severe. 4. The bending stress was setted successfully through $80^{\circ}C$-15hrs drying after bending and the spring back for 24hr-exposing time was only about 1%.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.248-253
• /
• 1998

Recently, the uses of Ceramic/metal bonded joints, resin/metal joints, adhesive joints, composite materials which are composed of dissimiliar materials have increased in various industry fields. Since the ceramic/metal bonded joints material is made at a high temperature, residual stress distributions due to differences in material properties were investigated by varying material parameters. The two dimensional finite element analysis was performed to study residual stress distribution in Si3N4/SM45C bonded joint with a copper interlayer between the silicon nitride(Si3N4) and the structural carbon steel(SM45C) and 4-point bending tests were carried out under room temperature. Fracture surface and crack propagation path were observed using scanning electron microscope and characteristics of its fracture was discussed.

• Journal of Power System Engineering
• /
• v.8 no.4
• /
• pp.44-48
• /
• 2004

For many years researchers have been attempting to establish the relations among the preparation history, structure and properties of ceramics. In this study, the strength property of $Al_2O_3$ ceramics with components and giudes of the textile machinery was investigated. The optimized conditions of ressureless sintering were investigated in order to obtain the maximum strength of $Al_2O_3$ ceramics for using at the textile machinery. As the sintering conditions, $1,400{\sim}1,700^{\circ}C$ of temperatures and $30{\sim}150$ minutes of times were applied. Three-point bending test was conducted on the sintered materials to obtain the strength property. From test results, the optimum sintering temperature has $1,600^{\circ}C$. And the optimum sintering time in $1,600^{\circ}C$ has about 100 minutes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.381-382
• /
• 2006

The mechanical behaviors of multi-layered foam core sandwich composite were investigated through a 3-point bending test. The sandwich specimens were obtained from sandwich panel consisting of aluminum faces and urethane foam core. Three types of sandwich specimens such as a single structure, a double structure and a triple structure were considered. The span of sandwich specimens were varied from 170mm to 350mm. According to the results, the flexural and shear properties of multi-layered sandwich composite were found to be higher than those of single-layered sandwich composite.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2006.05a
• /
• pp.24.1-24.1
• /
• 2006

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.715-718
• /
• 1998

In this work, bisphenol type vinyl ester was impregnated into the three-dimensional glass fabrics fabricated from different thickness changes. Their mechanical properties of the specimens have been investigated by three-point bending and flatwise compression tests. Also, interlaminar shear strength (ILSS) has been determined through short-beam test for the evaluation of interfacial adhesion at interfaces between fibers and matrix of the composites. The effect of thickness changes in three-dimensional glass fabric-reinforced composites have been described in this work.

• Journal of the Korean Society of Safety
• /
• v.30 no.3
• /
• pp.7-12
• /
• 2015

CFRP composites are used as primary structural members in various industrial fields because their specific strength and specific stiffness are excellent in comparison to conventional metals. Their usage is expanding to high added-value industrial fields because they are more than 50% lighter than metals, and have excellent heat resistance and wear resistance. However, when CFRP composites suffer impact damage, destruction of fiber and interface delamination occur. This causes an unexpected deterioration of strength, and for this reason it is very difficult to ensure the reliability of the excellent mechanical properties. Therefore, for the destruction mechanism in bending with impact damage, this study investigated the reinforcement data regarding various external loads by identifying the consequential strength deterioration. Specimens were damaged by impact with a steel ball propelled by air pressure. Decrease in bending strength caused by the tension and compression of the impact side, and depending on the lamination direction of fiber and interface inside the specimen. From the bending test it was found that the bending strength reduced when the impact energy increased. Especially in the case of compression on the impact side, as tensile stress occurred at the damage starting point, causing rapid failure and a substantially reduced failure strength.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.523-530
• /
• 2014

Machine material and structural strain are critical factors for appraising mechanical properties and safety. Particularly in three and four-point bending tests, which appraise the deflection and flexural strain of an object due to external force, measurements are made by the crosshead movement or deflection meter of a universal testing machine. The Digital Image Correlation (DIC) method is one of the non-contact measurement methods. It uses the image analyzing method that compares the reference image with the deformed image for measuring the displacement and strain of the objects caused by external force. Accordingly, the advantage of this method is that the object's surface roughness, shape, and temperature have little influence. However, its disadvantage is that it requires extensive time to compare the reference image with the deformed image for measuring the displacement and strain. In this study, an algorithm is developed for DIC that can improve the speed of image analysis for measuring the deflection and strain of an object caused by a three-point bending load. To implement this algorithm for improving the speed of image analysis, LabVIEW 2010 was used. Furthermore, to evaluate the accuracy of the developed fast correlation algorithm, the deflection of an aluminum specimen under a three-point bending load was measured by using the universal test machine and DIC measurement system.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.4
• /
• pp.26-34
• /
• 1989

This study was carried out to manufacture bark board from oak bark by new processes and to examine the physical and mechanical properties of the board. This process with no addition of adhesive used higher pressure and temperature than the conventional one and was applied with or without paraformaldehyde. The results are as follows: 1. The new manufacturing process allowed a good bark board with high absorption coefficient. 2. The best manufacturing process for the mechanical properties of bark board was paraformaldehyde 10%-$250^{\circ}C$-100kg/$cm^2$-3 minutes, (bending strength 40kg/$cm^2$, internal bonding strength 2kg/$cm^2$) and the best manufacturing process for both the mechanical properties of bark board and economic point of view was $250^{\circ}C$-100kg/$cm^2$-3 minutes (bending strength 28kg/$cm^2$, internal bonding strength 1.52kg/$cm^2$). 3. Bark board showed specific gravities from 0.94 to 1.03 and air dried moisture content 9.2% to 11.7%, but Bark board needed paraffin wax emusion treatment. 4. The absorption coefficient of bark boards had two peaks along with frequency; one in 200-400 cps, the other 1200-2000 cps. The former was low but the latter great.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.511-516
• /
• 1992

In this study, SiC powder and Si powder were used as the raw materials. Mixture was prepared with addition of Al2O3 and Fe2O3 at 0.1~0.5wt% respectively. After this step, the mixture was pressed and nitrided for 30 hrs at 140$0^{\circ}C$ under NH3-N2 atmosphere. Mechanical properties of sintered specimens were investigated from measurement of porosity, bulk density and three point bending test. nitration reaction extent was observed at the change of mass before and after reaction, and the microstructure and the change of $\alpha$-Si3N4 and $\beta$-Si3N4 were observed by XRD and SEM. In the current work, the results are as follows 1. When Fe2O3 added, the nitridation increased with the content of Fe2O3, and the bending strength was increased from 0.1 wt% to 0.3 wt%, and decreased to 0.5 wt%. 2. When Al2O3 added, the nitridation and the bending strength increased little by little with the content of Al2O3 3. The bending strength of the specimen added with Fe2O3 were higher than that with Al2O3. Because the specimens contained Fe2O3 had much more the whisker type crystal of Si3N4 contributing to strength than contained Al2O3.