• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.602-610
• /
• 2012

The powders for the $Na_xWO_3$ (x= 1 and 0.75) sputtering targets were synthesized by the calcination in reductive atmosphere. Near single-phase $NaWO_3$ and single-phase $Na_{0.75}WO_3$ powder targets were prepared. By using the targets, thin films of each composition were deposited by rf magnetron sputtering on the $SiO_2$ (100 nm)/Si substrates and annealed by RTP (rapid thermal processing) for crystallization. In the case of the $NaWO_3$ composition, single-phase $Na_xWO_3$ thin films, where x was believed to be slightly less than 1, were fabricated accompanying the Na-diffusion into the substrates during RTP. However, in the case of the $Na_{0.75}WO_3$ thin film preparation, it was unable to make single-phase thin films. From the phase formation behaviors of both powders and thin films, it was revealed that $Na_xWO_3$ with nonstoichiometric composition of x, which was slightly less than 1, was favorable. The good electrical conduction properties were obtained from the single-phase $Na_xWO_3$ thin films. Their electrical resistivities were as low as $7.5{\times}10^{-4}{\Omega}{\cdot}cm$.

• Journal of the Korean Ceramic Society
• /
• v.44 no.9
• /
• pp.471-476
• /
• 2007

The hydration mechanism of the $3CaO{\cdot}Al_2O_3-CaSO_4{\cdot}2H_2O$ system in the presence of alkali sulfates has been investigated. The early hydration rate of $3CaO{\cdot}Al_2O_3$ was accelerated by the addition of $Na_2SO_4$ and $K_2SO_4$. This is closely related to the formation of syngenite $(CaSO_4{\cdot}K_2SO_4{\cdot}H_2O)$, and the U-phase added $K_2SO_4$ and $Na_SO_4$ in the $3CaO{\cdot}Al_2O_3-CaSO_4{\cdot}2H_2O$ system, respectively. The formation of the rigid syngenite and U-phase structure led to rapid setting and decreases the sulfate content in the liquid phase of the hydrating cement to the extent that it cannot adequately retard the hydration of $3CaO{\cdot}Al_2O_3$. In case of the alkali sulfate not added to the $3CaO{\cdot}Al_2O_3-CaSO_4{\cdot}2H_2O$ system, the ettringite was transformed to monosulfoaluminate immediately after the consumption of gypsum. However, when the alkali sulfates were added to this system, the ettringite did not transform to monosulfoaluminate immediately even though the gypsum was completely consumed. There was a stagnation period to transform to the monosufoaluminate after the consumption of gypsum because the syngenite and U-phase remained as the sulfate source.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.496-503
• /
• 2009

In this paper, a new three-phase interleaved isolated high efficiency boost dc-dc converter with active clamp is proposed. The converter is capable of increased power transfer due to its three-phase power configuration, and it reduces the rms current per phase, thus reducing conduction losses. Further, interleaved operation of three-phase boost converter reduces overall ripple current, which is imposed into fuel cells and realizes smaller sized filter components, increasing effective operating frequency and leading to higher power density. Each output current of three-phase boost converter is combined by the three-phase transformer and flows in the continuous conduction mode by the proposed three-phase PWM strategy. An efficiency of above 96% is mainly achieved by reducing conduction losses and switching losses are reduced by the action of active clamp branches, as well. The proposed converter and three-phase PWM strategy are analyzed, simulated and implemented in hardware. Experimental results are obtained on a 500 W prototype unit, with all of the design verified and analyzed.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.324-332
• /
• 1998

The grain growth characteristics of dual-phase (${\alpha}+{\gamma}$) containing high Cr-steel have investigate using ${\alpha}$-, ${\gamma}$-single phases and (${\alpha}+{\gamma}$)dual-phase of 12%Cr Steel. The heat treatment has performed at $1000-1200^{\circ}C$ for 1-100hr. The results are as follows : 1) The grain growth rate in (${\alpha}+{\gamma}$) dual phase was substantially slower than that of single grain. 2) The relation between mean grain radius $\bar{{\gamma}}$ and annealing time t is, in general, described as following equation : $$(\bar{{\gamma}})^n-(\bar{{\gamma}_o})^n=K_n{\cdot}t{\cdots}{\cdots}(1)$$ i) In the case of single phase of high Cr steel, Eq.(1) is described as $(\bar{{\gamma}})^2-(\bar{{\gamma}_o})^2=K_2{\cdot}t$ and the grain growth is controlled by boundary migration. ii) In dual phase, the grain growth needs diffusion of alloying elements because the chemical composition of ${\alpha}$- and ${\gamma}$- phases differs from each other. When the volume fraction of ${\alpha}$-, ${\gamma}$-phase was almost equal and ${\gamma}$-phase in the case of 80 and $90%{\gamma}$. Eq.(1) is described as $(\bar{{\gamma}})^3-(\bar{{\gamma}_o})^3=K_3{\cdot}t$ because the grain growth is controlled by volume diffusion iii) In the case of ${\gamma}$-rich phase (80 and $90%{\gamma}$), the grain growth of minor phase (10 and $20%{\alpha}$) is described as $(\bar{{\gamma}})^4-(\bar{{\gamma}_o})^4=K_4{\cdot}t$ because the boundary diffusion is predominent rather than volume diffusion.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.3
• /
• pp.213-218
• /
• 2020

In this study, we propose a control algorithm to reduce the unbalanced characteristics of a three-phase system power caused by the unbalanced load of the AC electric railway. Then, we verify its performance through the design of a power compensator and experiments applying it. Like electric railway systems, a Scott transformer is applied, and the load and single-phase back-to-back converters are connected to the M-phase and T-phase outputs. The back-to-back converter monitors the difference in active power between the unbalanced loads in real-time and compensates for the power by using bidirectional characteristics. The active power is performed through PI control in the synchronous coordinate system, and DC link overall voltage and voltage balancing control are controlled jointly by M-phase and T-phase converters to improve the responsiveness of the system. To verify the performance of the proposed power compensation device, an experiment was performed under the condition that M-phase 5 kW and T-phase 1 kW unbalanced load. As a result of the experiment, the unbalance rate of the three-phase current after the operation of the power compensator decreases by 58.66% from 65.04% to 6.38%, and the excellent performance of the power compensator proposed in this study is verified.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.768-775
• /
• 2022

Current MEP designs are mostly applied by 2D-based design methods and tend to focus on simple modeling or geometry information expression such as converting 2D-written drawings into 3D modeling without taking advantage of the strength of BIM application. To increase the demand for BIM-based MEP design, geometric information, and property information of each member of the 3D model must be conveniently linked from the phase of the Design Development (DD) to the phase of Construction Document (CD). To conveniently implement a detailed model at each phase, the detailed level of each member of the 3D model must be specific, and an automatic generation of objects at each phase and automatic detailing module for each LOD are required. However, South Korea's guidelines have comprehensive standards for the degree of MEP modeling details for each design phase, and the application of each design phase is ambiguous. Furthermore, in practice, detailed levels of each phase are input manually. Therefore, this paper summarized the detailed standards of MEP modeling for each design phase through interviews with MEP design companies and related literature research. In addition, items that enable auto-detailing with DYNAMO were selected using the checklist for each design phase, and the types of detailed methods were presented. Auto-detailing items considering the detailed level of each phase were classified by members. If a DYNAMO algorithm is produced that automates selected auto-detailing items in this paper, the time and costs required for modeling construction will be reduced, and the demand for MEP design will increase.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.355-359
• /
• 2000

This paper deal with the harmonic reduction technique in three-phase square-wave inverter system formed by single-phase inverter. To reduce the harmonics six single-phase inverters are used for forming multi-phase inverter and zig-zag connected output transformer for eliminating the harmonic 6(2k-1)$\pm$1 orders. And an ac filter is furnished at output side. Computer simulations show that the THD of the output voltage can be reduced immensely.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.307-310
• /
• 1999

This paper proposes a novel current control method of three-phase PWM rectifiers without phase current sensors. The features of this method are to reconstruct phase currents by using switching pattern of space vector modulation and to estimate phase currents by a predictive state observer for practical applications. Simulation results show that the performance of the proposed system is nearly the same as that of sensor-based system.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.8
• /
• pp.281-288
• /
• 1984

A new method of protecting 3-phase squirrel-cage induction motor aginst burning-out by unbalance operation is proposed. This paper studied various kinds of situations occurred by unbalance operating in 3-phase induction motor, and we provided the search coils in the slots of stator and rotor for the purpose of detecting electrical phenpmena during unbalance operation. Through experiments, we find that search coils in the slots of stator is effective method for protecting the induction motor from unbalance operating.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.222-227
• /
• 1997

Unbalanced source voltages due to unbalanced loads in the 3-phase power system is decomposed into positive, negative and zero sequence components. Also, assuming there is no neutural path in the system, the zero sequence component is not shown. Therefore, it is possible to compensate unbalanced source voltage by canceling the negative sequency component of the voltages of the source. In this paper, an algorithm compensating unbalanced source voltages by canceling the negative sequence component is presented and analysis of instantaneous voltage compensator using 3-phase PWM inverter is carried out through computer simulation.