• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.113-119
• /
• 2006

It is now established that more than two types of blended aggregate have beneficial effects on quality and supply of concrete in the long run. However, studies on blended aggregate have not widely been progressive and the evaluation method of its most favorable mixture proportion is still needed. Therefore this study investigated the most favorable mixture proportion through the physical experiment of fresh and hardened state's cement mortar, in response to three types of composite ratio, natural fine aggregate(Ns), crushed fine aggregate(Cs) and recycled fine aggregate(Rs). Test showed that increase of blending ratio of Ns and Cs improved fluidity of mot1ar. For the properties of compressive and flexural strength, mortar blending Ns and Cs properly, exhibited similar value to one using only Cs, while mortar mixing Rs showed lower strength value as less as 6% of control one. Mortar using only Rs exhibited the largest drying shrinkage value. In addition, even thought it is not a clear quantitative analysis, technical-imaging-skill presenting the most favorable mixture proportion 3-dimensionally is proposed in this research, in order to notify the proportion easily.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.1
• /
• pp.70-81
• /
• 2009

Statement of problem: The position and length of cantilever influence on the stress distribution of implants, superstructure and bone. In edentulous mandible, implant-supported cantilever prostheses that based 4 or 6 implants between mental foramens has been attempted. Excessive bite force loaded at cantilever prosthesis causes bone resorption and breakage of superstructure prosthesis around posterior implants. To complement the cantilever length of conventional prosthesis, In 1992, (McCartney) introduced "cantilever-rest-implant" and Malo reported "All-on-Four" in 2003. Purpose: Analyze and compare the stress distribution of conventional cantilever prostheses with rest implant and All-on-$Four^{TM}$ implant prostheses. Material and method: The external loads(300 N vertically, 75 N horizontally) are applied to first molar area. The stress value, stress distribution and aspect of stress dispersion are analyzed by three-dimensional finite element analysis program, ANSYS ver. 10.0. Results: 1. The rest implant and "All-on-Four" implant system are superior to conventional cantilever prostheses to reduce stress on the bone and the superstructure around implants. 2. The rest implant was of the greatest advantage to stress distribution on bone, implant and superstructure. 3. With same number of implants, distally tilted implants are preferred to conventional cantilever prostheses for reducing the length of cantilever.

• Applied Biological Chemistry
• /
• v.29 no.3
• /
• pp.318-323
• /
• 1986

We empolyed gel filtraction, polyacrylamide gel electrophoresis, amino acid autoanalyzer, thin layer chromatography for determining protein and lipid composition in walnut. The walnut contained 22.18% of crude protein and 64.23% of crude lipid. Glutamic acid (38.60%) was the major amino acid in soluble protein, followed by arginine and aspartic acid. The sodium dodecyl sulfate polyacrylamide gel electrophoresis analysis showed 12 band in soluble protein of walnut, and collection rate of main protein fraction purified by Sephadex G-150 was 60.67%. The molecular weight for the main protein was estimated to be 43,000. The lipid fraction obtained by silicic acid column chromatography were mainly composed of about 93.05% neutral lipid, whereas compound lipid was only 7.0% level. Among the neutral lipid by thin layer chromatography, triglyceride was 82.05%, sterol ester and free fatty acid were 3.86% and 4.80%, repectively. The predominant fatty acids of total and neutral lipids were linoleic acid $(64.48{\sim}69.98%)$ and oleic acid $(13.89{\sim}15.36%)$. The major fatty acids of triglyceride separated from neutral lipid were linolenic acid (69.98%).

• Korean Journal of Ecology and Environment
• /
• v.47 no.3
• /
• pp.167-175
• /
• 2014

This study was conducted to quantify a carbon budget of major vegetation types established in the campus of the National Institute of Ecology (NIE). Carbon budget was measured for Pinus thunbergii and Castanea crenata stands as the existing vegetation. Net Primary Productivity (NPP) was determined by applying allometric method and soil respiration was measured by EGM-4. Heterotrophic respiration was calculated as 55% of total respiration based on the existing results. Net Ecosystem Production (NEP) was determined by the difference between NPP and heterotrophic respiration (HR). NPPs of P. thunbergii and C. crenata stands were shown in $4.9ton\;C\;ha^{-1}yr^{-1}$ and $5.3ton\;C\;ha^{-1}yr^{-1}$, respectively. Heterotrophic respirations of P. thunbergii and C. crenata stands were shown in $2.4ton\;C\;ha^{-1}yr^{-1}$ and $3.5ton\;C\;ha^{-1}yr^{-1}$, respectively. NEPs of P. thunbergii and C. crenata stands were shown in $2.5ton\;C\;ha^{-1}yr^{-1}$ and $1.8ton\;C\;ha^{-1}yr^{-1}$, respectively. Carbon absorption capacity for the whole set of vegetation types established in the NIE was estimated by applying NEP indices obtained from current study and extrapolating NEP indices from existing studies. The value was shown in $147.6ton\;C\;ha^{-1}yr^{-1}$ and it was calculated as $541.2ton\;CO_2ha^{-1}yr^{-1}$ converted into $CO_2$. This function corresponds to 62% of carbon emission from energy that NIE uses for operation of various facilities including the glass domes known in Ecorium. This carbon offset capacity corresponds to about five times of them of the whole national territory of Korea and the representative rural area, Seocheongun. Considered the fact that ongoing climate change was originated from imbalance of carbon budget at the global level, it is expected that evaluation on carbon budget in the spatial dimension reflected land use pattern could provide us baseline information being required to solve fundamentally climate change problem.

• The korean journal of orthodontics
• /
• v.38 no.5
• /
• pp.304-313
• /
• 2008

Objective: The purpose of this study was to evaluate the stress distribution in bone and displacement distribution of the miniscrew according to the length and number of the miniscrews used for the fixation of miniplate, and the direction of orthodontic force. Methods: Four types of finite element models were designed to show various lengths (6 mm, 4 mm) and number (3, 2) of 2 mm diameter miniscrew used for the fixation of six holes for a curvilinear miniplate. A traction force of 4 N was applied at $0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$ to an imaginary axis connecting the two most distal unfixed holes of the miniplate. Results: The smaller the number of the miniscrew and the shorter the length of the miniscrew, the more the maximum von Mises stress in the bone and maximum displacement of the miniscrew increased. Most von Mises stress in the bone was absorbed in the cortical portion rather than in the cancellous portion. The more the angle of the applied force to the imaginary axis increased, the more the maximum von Mises stress in the bone and maximum displacement of the miniscrew increased. The maximum von Mises stress in the bone and maximum displacement of the miniscrew were measured around the most distal screw-fixed area. Condusions: The results suggest that the miniplate system should be positioned in the rigid cortical bone with 3 miniscrews of 2 mm diameter and 6 mm length, and its imaginary axis placed as parallel as possible to the direction of orthodontic force to obtain good primary stability.

• Journal of Wetlands Research
• /
• v.20 no.2
• /
• pp.155-160
• /
• 2018

We investigated to know the growth patterns of Aedes albopictus larva at the four different temperature conditions. Each of 120 individuals was placed into a $20m{\ell}$ vial and 12 sets (a set of 10 vials) were separated into 12 water tanks ($17{\times}24{\times}18cm^3$). Each water tank was composed of 3 the $1^{st}$ instar, 3 the $2^{nd}$ instar, 2 the $3^{rd}$ instar, and 2 the $4^{th}$ instar. Three sets of water tanks were placed under the four different incubator temperatures ($17^{\circ}C$, $21^{\circ}C$, $24^{\circ}C$, $28^{\circ}C$). We found that the eclosion rates were $20.00{\pm}5.77%$ at $21^{\circ}C$ and $3.33{\pm}3.33%$ at other temperatures. For the mosquito larva mortality rate, $1^{st}$ instar was $19.24{\pm}3.65%$, $2^{nd}$ instar was $16.48{\pm}3.25%$, $3^{rd}$ instar was $23.54{\pm}5.06%$, and $4^{th}$ instar was $40.74{\pm}7.08%$. The lowest mortality rate in growth stages according to temperature was $13.33{\pm}6.67%$ at $17^{\circ}C$ in $1^{st}$ instar larva, $7.41{\pm}7.41%$ at $21^{\circ}C$ at $2^{nd}$ instar larva, $10.74{\pm}6.43%$ at $24^{\circ}C$ in $3^{rd}$ instar larva, and $20.37{\pm}5.46%$ at $28^{\circ}C$ in $4^{th}$ instar larva. The survival period of mosquitoes in underwater were $26.33{\pm}0.67days$ at $17^{\circ}C$, $23.33{\pm}1.33days$ at $21^{\circ}C$, $20.00{\pm}2.52days$ at $24^{\circ}C$, and $11.67{\pm}1.20days$ at $28^{\circ}C$. From our results the most effective temperature to the normal growth of mosquito larva was $21^{\circ}C$, and the highest mortality rate was shown at the $4^{th}$ instar stage of larva growth. Our results would provide the basic data for the mosquito larva's growth pattern.

• Journal of Korean Ophthalmic Optics Society
• /
• v.10 no.3
• /
• pp.193-203
• /
• 2005

Highly c-axis oriented nanocrystalline ZnO thin films on silica glass substrates were prepared by spin coating-pyrolysis process with a zinc naphthenate precursor. Only the XRD intensity peak of (002) phase was observed for all samples. With an increase in heat treatment temperature, the peak intensity of (002) phase increases. No significant aggregation of particle was present. From scanning probe microscopy analyses, three-dimensional grain growth, which was thought to be due to inhomogeneous substrate surface and c-axis oriented grain growth of the ZnO phase, was independent on heal-treatment temperature. Highly homogeneous surface of the highly-oriented ZnO film was observed at $800^{\circ}C$. All the films exhibited a high transmittance (above 80%) in visible region except film heat treated at $1000^{\circ}C$, and showed a sharp fundamental absorption edge at about $0.38{\sim}0.40{\mu}m$. The estimated energy band gap for all the films were within the range previously reported for films and single crystal. ZnO films, consisting of densely packed grains with smooth surface morphology were obtained by heat treatment at $600^{\circ}C{\sim}800^{\circ}C$, expected to be ideal for practical application, such as transparent conductive film and optical device.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6447-6454
• /
• 2013

Seawater intake systems have significant problems due to seawater pollution, suspended solids, unstable intake and maintenance etc. An underground type seawater intake system was newly developed to overcome the existing weaknesses and was facilitated in Gyukpo port. In this study, to check the performance of the new system, the samples for water quality and the 3-D numerical modeling test were conducted. The five times test included the COD, total nitrogen, total phosphorus, pH, and suspended solid for the intake system. The analyses show that the COD, total nitrogen, total phosphorus, PH showedminor changes before and after. On the other hand, the change in suspended solids was significant and water was purified below 5 mg/l, first level fisheries water, after. The numerical model adopted the RNG $k-{\epsilon}$ algorithm and the CFX model based on the finite volume method. The porosity algorithm was used to reproduce filtered-sand, outer diameter, and thickness. The numerical results showed that the double pipe is advantageous in that it provides a uniform pressure between the inner and outer pipe for the flow to be stable. In addition, the use of multiple intake pipes did not interfere with the discharge reduction of 0.98 at the both intake pipes compared with the central intake pipe.

• Journal of the Korean Society for Railway
• /
• v.12 no.1
• /
• pp.31-38
• /
• 2009

The selection of the support system is an important design parameter in design and construction of the tunnel using the new Australian tunnel method. It is a common practice to select the support based on the rock mass grade, in which the rock mass is classified into five rock groups. The method is applicable if the characteristics of the rock mass are uniform in the direction of tunnel excavation. However, such case is seldom encountered in practice and not applicable when the properties vary along the longitudinal direction. This study performs comprehensive three dimensional finite difference analyses to investigate the ground deformation pattern for cases in which the rock mass properties change in the direction of the tunnel axis. The numerically calculated displacements at the tunnel crown show that the displacement is highly dependent on the stiffness contrast of the rock masses. The results strongly indicate the need to select the support type $0.5{\sim}1.0D$ before the rock mass boundary. The paper proposes a new guideline for selecting the support type based the results of the analyses.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.7-12
• /
• 2004

탄화규소 전력반도체 소자는 실리콘 전력반도체 소자에 비해 우수한 물질특성을 갖고 있어 성능 측면에서 뿐 만 아니라 전력변환장비의 크기를 획기적으로 줄일 수 있는 새로운 반도체 소자이다. 특히 unipolar 계열의 소자에서 괄목할 만한 특성을 보이고 있다. 현재 쇼트키 장벽 다이오드의 경우 5kV급, UMOSFET의 경우 3kV급의 소자까지 보고되고 있으며 반도체 물질 중에서 가장 활발히 연구가 진행되고 있는 분야 중의 하나이다. 단결정성장 분야에서도 3인치 급이 상용화 되었으며 4인치 크기의 웨이퍼의 상용화가 조만간 실현될 것으로 기대되고 있다. 이러한 기술적 발전을 토대로 600V, 1200V급 쇼트키 다이오드가 PFC boost 용으로 시판되고 있으나 아직은 다른 반도체 소자에 비해 미미한 실정이다. 현재에는 $250^{\circ}C$까지의 온도영역에서 실리콘 SOI(Silicon on Insulator) 소자가 주로 사용되고 있다. 그러나 $300^{\circ}C$를 넘는 온도 영역에서는 실리콘으로는 한계가 있고, 특히 SOI는 전력소자에 적용하기는 한계가 있어 주로 저전력 고온소자가 필요한 부분에 적용이 되고 있다. 따라서 전력용에 적합한 고온소자로 탄화규소 소자의 연구가 활발히 진행되고 있다. 현재의 추세로 보아 $200-300^{\circ}C$ 영역의 응용분야에서는 SOI와 탄화규소가 함께 적용될 것으로 예상되며, $300^{\circ}C$를 넘는 온도영역에서는 탄화규소 소자의 우월적 지위가 예상된다. 이러한 이유로 탄화규소 반도체소자의 응용 분야는 크게 확대될 것으로 예상되며 국가적 차원의 지원 및 육성이 요구되는 분야 중의 하나이다.t로 사용한 소자보다 발광 소광 현상이 적게 일어난 것에 기인하였다고 생각된다. 두 소자 모두 $40mA/cm^2$ 에서 이상적인 화이트 발란스와 같은(0.33,0.33)의 색좌표를 보였다.epsilon}_0=1345$의 빼어난 압전 및 유전특성과 $330^{\circ}C$의 높은 $T_c$를 보였고 그 조성의 vibration velocity는 약4.5 m/s로 나타났다.한 관심이 높아지고 있다. 그러나 고 자장 영상에서의 rf field 에 의한 SAR 증가는 중요한 제한 요소로 부각되고 있다. 나선주사영상은 SAR 문제가 근원적으로 발생하지 않고, EPI에 비하여 하드웨어 요구 조건이 낮아 고 자장에서의 고속영상방법으로 적합하다. 본 논문에서는 고차 shimming 을 통하여 불균일도를 개선하고, single shot 과 interleaving 을 적용한 multi-shot 나선주사영상 기법으로 $100{\times}100$에서 $256{\times}256$의 고해상도 영상을 얻어 고 자장에서 초고속영상기법으로 다양한 적용 가능성을 보였다. 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타나며 그 유의성이 움직임 보정 전에 비하여 낮음을 알 수 있었다. 결론: 뇌활성화 과제 수행시에 동반되는 피험자의 머리 움직임에 의하여 도파민 유리가 과대평가되었으며 이는 이 연구에서 제안한 영상정합을 이용한 움직임 보정기