• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.79-84
• /
• 2012

This study consist of two parts. One is development of a self-propelling vinyl remover which was already reported at the previous paper. This is the second part of the study. For the study, an attached vinyl remover was developed. It was consisted of connecting tractor to bucket, removing bucket from tractor, and the process was the tractor's assistance hydraulics. In the case of an attached vinyl remover, the vinyl was twisted 0.5times per 30~85cm length. The bobbin's diameter was 190mm and it's stable travelling speed was 1m/s. The revolution of the remover wheel was 90rpm to maintain the wheel's linear velocity. As seen at performance test at the field which had 950mm ridge intervals and 10 a area, the average working speed was 1m/s and the turning time was 20seconds. Therefore, the working performance was 24.5min/10a. The efficiency of used vinyl remover was 97% and working conditions were good.

• 한국정밀공학회지
• /
• 제13권6호
• /
• pp.52-58
• /
• 1996

This paper described on the effect of residual stocks in internal grinding of tungsten carbide materials in order to improve the grinding efficiency as well as grinding accuracy. Through the fundamental investigation is carried out for tungsten carbide materials using electroplated diamond wheel, the residual stock after grinding process is effective to the grinding efficiency. The obtained results are as follows: (1) Under the depth of cut(t) is constant and decreasing the workpiece velocity(Vw), the residual stock after grinding is increased, but the difference is little less than the difference by table speed. (2) Increasing the wheel velocity, the residual stock after grinding is decreased. Therefore in order to minimize the residual stock, the wheel velocity should be increased as far as possible. (3) The surface roughness and out-of roundness increased with depth of cut and table speed, and decreased with wheel velocity, but it may as well adopt as much as possible under the dimensional tolerance which is required for high efficiency grinding. (4) In order to remove residual stock, the spark-out grinding shoule be done, and it also can be improved about 20~25% throughout spark-out grinding, and the number of optimal spark-out times were within 10 times.

• International Journal of Automotive Technology
• /
• 제3권2호
• /
• pp.63-70
• /
• 2002

Future on-board vehicle control systems can be further improved through new types of mechatronic systems. In particular, these systems' capacities for interaction enhance safety, comfort and economic viability. The Automotive Engineering Department (fzd) of darmstadt University of Technology is engaged in research of the mechatronic vehicle corner, which consists of three subsystems: sensor tire, electrically actuated wheel brake and smart suspension. By intercommunication of these three systems, the brake controller receives direct, fast and permanent information about dynamic events in the tire contact area provided by the tire sensor as valuable control input. This allows to control operation conditions of each wheel brake. The information provided by the tire sensor for example help to distinguish between staightline driving and cornering as well as to determine $\mu$-split conditions. In conjunction with current information of dynamic wheel loads, tire pressures and friction tyre/road, the ideal brake force distribution can be achieved. Alike through integration of adaptive suspension bushings, elastokinematic behaviour and wheel positions can be adapted to manoeuver-oriented requirements.

• Journal of Biosystems Engineering
• /
• 제13권2호
• /
• pp.28-37
• /
• 1988

This study was conducted to construct the soil bin system and associated microcomputer-based data acquisition system which is to be used for the effective evaluation of wheel performance. The soil bin system consists of four main parts; soil bin, carriage drive system, test carriage and soil processing carriage. The test carriage was constructed to measure the five performance parameters of testing wheels; pulling forte, motion resistance, sinkage and rotational speed of test wheel, and speed of test carriage. The test wheel is powered by a hydraulic system up to 8 ps. Soil processing carriage was designed to provide uniform test soil condition across the toil bin, and reproduction of soil conditions found satisfiable. The data acquisition system consists of APPLE II PLUS microcomputer, strain amplifier, I/O interface, A/D converter, digital counter and various transducers. It takes about 0.86 seconds to measure a set of performance parameters and store on the floppy disk simultaneously. Series of experiment showed that this system can be used effectively for evaluating the wheel performance associated with soil.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.101-109
• /
• 1994

Recently, four-wheel steering systems have been developed and studied as one of the latest automotive technologies for improving the handling characteristics of a vehicle. In much of the proposed four-wheel steering systems, the side slip angle at the vehicle's center of gravity is maintained at zero. This approach allows the greater maneuverability at low speed by means of counter-phase rear steering and the improved stability at high speed through same-phase rear steering. In this paper, the effects of several four-wheel steering systems are studied and discussed on the responsiveness and stability of the vehicle by using the linear analysis. Especially, the effects of the cornering stiffnesses of both front and rear wheels are investigated on the yaw velocity gain and critical speed of the vehicle.

• 한국도로학회논문집
• /
• 제15권1호
• /
• pp.103-110
• /
• 2013

PURPOSES: The objective of this study is to analyze and evaluate the behavior of orthotropic steel bridge deck pavement using three-dimensional finite element analysis and full-scale wheel load testing. METHODS: Since the layer thickness and material properties used in the bridge deck pavement are different from its condition, it is very difficult to measure and access the behavior of bridge deck pavement in the field. To solve this problem, the full-scale wheel load testing was conducted on the PSMA/Mastic bridge deck pavement and the deflection of bridge deck and horizontal tensile strain on top of pavement were measured under the loading condition. Three-dimensional finite element analysis was conducted to predict the behavior of bridge deck pavement and the predicted deflection and tensile strain values are compared with measured values from the wheel loading testing. RESULTS: Test results showed that the predicted deflections are 10% lower than measured ones and the error between predicted and measured horizontal tensile strain values is less than 2% in the critical location. CONCLUSIONS: The fact indicates that the proposed the analysis is found to be accurate for estimating the behavior of bridge deck pavements.

• 한국결정학회지
• /
• 제15권2호
• /
• pp.78-82
• /
• 2004

벤젠 존재 하에서, DMF와 에탄올의 혼합 용매에서 zinc(II) nitrate $(Zn(NO_3)_2\;{\cdot}\;6H_2O)$와 $ATP(2-aminoterephthalate,\;H_2N-C_6H_3-1,4-(COO)_2)$의 용매열 반응으로 2차원 배위 고분자 [Zn(ATP) (DMF)] (1)이 얻어졌다 X-ray구조 결정 결과, 2개의 아연 금속과 4개의 ATP 리간드가 paddle-wheel유형의 2차 쌓음 단위들을 형성하고, 이것들은 ATP 리간드에 의해서 연결되어 2차원 4각 망을 이룬다는 것이 밝혀졌다. 아연 금속을 기준으로 각 4각형의 크기는 약$11.1\times11.1\;{\AA}$효이다. 고분자 1을 양질의 결정 상태로 얻기 위해서는 벤젠이 요구되었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1888-1893
• /
• 2011

Considering the dynamic performance and stability of railroad vehicles has begun to grab the attention because of developing the high speed train recently. A development based on an analysis of dynamics and verification has to be required to study the stability of vehicle performance. Several ways of analysis were using the look-up table to apply the wheel-rail contact characteristics quickly, whereas there is a constraint of the wheelset lateral displacement. In this study, an development of searching the wheel-rail contact position has been provided. The 2-point contact between wheel and rail during the driving condition can be calculated by numerical analysis. Moreover, a reliability is verified by comparing the result with a commercial program.

• 한국정밀공학회지
• /
• 제2권2호
• /
• pp.60-68
• /
• 1985

The Surface roughness is affected by the factors such as elements of grinding wheel, grinding conditions, and so on. Of all these factors, we studied surface roughness variation in accordance with grain size of grinding wheel and grinding depth of cut on the surface grinding. Tempered, annealed, quenched, and non-heat treated materials were used as specimen. The results obrained in these experiments are as follows: 1) The smaller the hardness is, the better the grinding surface roughness becomes. 2) Tempered materials after quenching shows the finest finished surface on grinding.

• 한국정밀공학회지
• /
• 제17권2호
• /
• pp.7-14
• /
• 2000

본 글은 1999년 5월 CASA/SME Blue Book에 Jim Jordan 그리고 Fred Michel이 “Next Generation Manufacturing”라는 제목으로 게재한 자료를 편자의 의도에 따라 재편집한 것입니다. CASA(Computer and Automated Systems Association)는 SME(Society of Manufacturing Engineers)에서 활동하고 있는 하나의 분과로서 CIM Enterprise Wheel을 만들어 내 유명한 곳이기도 합니다. 저자는 본 괌에서 앞으로 10여 년 간 펼쳐질 차세대 제조 시스템에서는 지식의 경영이 가장 중요한 요소라고 정의하고 있습니다. 그리고 차세대 제조 시스템의 운영전략으로는 기업통합, 인간자원의 지적이용, 지식의 개발 및 유지, NGM 프로세스 장비 및 기술의 채용을 들고 있습니다. 차세대 제조 시스템(1)은 전월호에서 소재되었습니다.